I.S. EN 62137-1-2:2007
Current
The latest, up-to-date edition.
SURFACE MOUNTING TECHNOLOGY - ENVIRONMENTAL AND ENDURANCE TEST METHODS FOR SURFACE MOUNT SOLDER JOINT - PART 1-2: SHEAR STRENGTH TEST
Hardcopy , PDF
English
01-01-2007
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General remarks
5 Test equipment and materials
5.1 Shear test equipment
5.2 Pushing tool
5.3 Optical microscope
5.4 Scanning electron microscope (SEM)
5.5 Reflow soldering oven
5.6 Test substrate
5.7 Solder alloy
5.8 Solder paste
6 Mounting method
7 Test conditions
7.1 Test: Rapid change of temperature
7.2 Shear strength test
8 Test procedure
8.1 Test sequence
8.2 Pre-conditioning
8.3 Initial shear strength
8.4 Rapid change of temperature
8.5 Recovery
8.6 Intermediate/final shear strength
9 Items to be included in the test report
10 Items to be given in the product specification
Annex A (normative) - Shear strength test - Details
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding
European publications
Applies to leadless surface mounting components and surface mounting connectors to which pull test is not applicable. It is not applicable to multi-lead components and gull-wing leads.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| EN 62137-1-2:2007 | Identical |
| NF EN 62137-1-2 : 2014 | Identical |
| NBN EN 62137-1-2 : 2007 | Identical |
| IEC 62137-1-2:2007 | Identical |
| BS EN 62137-1-2:2007 | Identical |
| DIN EN 62137-1-2:2008-02 | Identical |
| IEC 61188-5-2:2003 | Printed boards and printed board assemblies - Design and use - Part 5-2: Attachment (land/joint) considerations - Discrete components |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 61190-1-2:2014 | Attachment materials for electronic assembly - Part 1-2: Requirements for soldering pastes for high-quality interconnects in electronics assembly |
| IEC 61249-2-7:2002 | Materials for printed boards and other interconnecting structures - Part 2-7: Reinforced base materials clad and unclad - Epoxide woven E-glass laminated sheet of defined flammability (vertical burning test), copper-clad |
| IEC 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| EN 61760-1:2006 | SURFACE MOUNTING TECHNOLOGY - PART 1: STANDARD METHOD FOR THE SPECIFICATION OF SURFACE MOUNTING COMPONENTS (SMDS) |
| IEC 61760-1:2006 | Surface mounting technology - Part 1: Standard method for the specification of surface mounting components (SMDs) |
| EN 61249-2-7:2002/corrigendum:2005 | MATERIALS FOR PRINTED BOARDS AND OTHER INTERCONNECTING STRUCTURES - PART 2-7: REINFORCED BASE MATERIALS CLAD AND UNCLAD - EPOXIDE WOVEN E-GLASS LAMINATED SHEET OF DEFINED FLAMMABILITY (VERTICAL BURNING TEST), COPPER-CLAD |
| EN 61188-5-2:2003 | Printed boards and printed board assemblies - Design and use - Part 5-2: Attachment (land/joint) considerations - Discrete components |
| IEC 60194:2015 | Printed board design, manufacture and assembly - Terms and definitions |
| IEC 61188-5-5:2007 | Printed boards and printed board assemblies - Design and use - Part 5-5: Attachment (land/joint) considerations - Components with gull-wing leads on four sides |
| EN 61190-1-3:2007/A1:2010 | ATTACHMENT MATERIALS FOR ELECTRONIC ASSEMBLY - PART 1-3: REQUIREMENTS FOR ELECTRONIC GRADE SOLDER ALLOYS AND FLUXED AND NON-FLUXED SOLID SOLDER FOR ELECTRONIC SOLDERING APPLICATIONS |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| EN 61190-1-2:2014 | Attachment materials for electronic assembly - Part 1-2: Requirements for soldering pastes for high-quality interconnects in electronics assembly |
| EN 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| EN 60194:2006 | Printed board design, manufacture and assembly - Terms and definitions |
| IEC 61190-1-3:2007+AMD1:2010 CSV | Attachment materials for electronic assembly - Part 1-3: Requirements for electronic grade solder alloys and fluxed and non-fluxed solid solders for electronic soldering applications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.