I.S. EN 61337-1:2005
Current
The latest, up-to-date edition.
FILTERS USING WAVEGUIDE TYPE DIELECTRIC RESONATORS - PART 1: GENERIC SPECIFICATION
Hardcopy , PDF
English
01-01-2005
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
1 General
1.1 Scope
1.2 Normative references
1.3 Order of precedence
2 Terminology and general requirements
2.1 General
2.2 Terms and definitions
2.3 Preferred ratings and characteristics
2.4 Marking
3 Quality assessment procedures
3.1 Primary stage of manufacture
3.2 Structurally similar components
3.3 Sub-contracting
3.4 Incorporated components
3.5 Manufacturer's approval
3.6 Approval procedures
3.7 Procedures for capability approval
3.8 Procedures for qualification approval
3.9 Test procedures
3.10 Screening requirements
3.11 Rework and repair work
3.12 Certified records of released lots
3.13 Validity of release
3.14 Release for delivery
3.15 Unchecked parameters
4 Test and measurement procedures
4.1 General
4.2 Test and measurement conditions
4.3 Visual inspection
4.4 Dimensions and gauging procedures
4.5 Electrical test procedures
4.6 Mechanical and environmental test procedures
Figures
Applicable to filters using waveguide type dielectric resonators of assessed quality using either capability approval or qualification approval procedures.
| DevelopmentNote |
Supersedes I.S. EN 171000. (02/2005) For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NF EN 61337-1 : 2005 | Identical |
| DIN EN 61337-1:2005-07 | Identical |
| IEC 61337-1:2004 | Identical |
| BS EN 61337-1:2004 | Identical |
| EN 61337-1:2004 | Identical |
| NBN EN 61337-1 : 2005 | Identical |
| HD 323.2.20 : 200S3 | BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST T - SOLDERING |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 60068-2-58:2015+AMD1:2017 CSV | Environmental testing - Part 2-58: Tests - Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD) |
| IEC 60068-2-27:2008 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| IEC 60068-2-20:2008 | Environmental testing - Part 2-20: Tests - Test T: Test methods for solderability and resistance to soldering heat of devices with leads |
| EN 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| IECQ 001002-3:2005 | IEC QUALITY ASSESSMENT SYSTEM FOR ELECTRONIC COMPONENTS (IECQ) - RULES OF PROCEDURE - PART 3: APPROVAL PROCEDURES |
| EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| IEC 60068-2-13:1983 | Basic environmental testing procedures - Part 2-13: Tests - Test M: Low air pressure |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| IECQ 001002-2:1998 | IEC QUALITY ASSESSMENT SYSTEM FOR ELECTRONIC COMPONENTS (IECQ) - RULES OF PROCEDURE - PART 2: DOCUMENTATION |
| EN 60068-2-7:1993 | Environmental testing - Part 2: Tests - Test Ga: Acceleration, steady state |
| EN 60068-2-27:2009 | Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock |
| EN 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| EN 60068-2-29:1993 | Environmental testing - Part 2: Tests - Test Eb and guidance: Bump |
| EN 60068-2-78:2013 | Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state |
| EN 60068-2-13:1999 | Environmental testing - Part 2: Tests - Test M: Low air pressure |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| IEC 60050-561:2014 | International Electrotechnical Vocabulary (IEV) - Part 561: Piezoelectric, dielectric and electrostatic devices and associated materials for frequency control, selection and detection |
| IEC 60068-2-29:1987 | Environmental testing. Part 2: Tests. Test Eb and guidance: Bump |
| IEC 60068-2-1:2007 | Environmental testing - Part 2-1: Tests - Test A: Cold |
| EN 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| EN 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| IEC 60068-2-30:2005 | Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.