I.S. EN 61243-3:2014
Current
The latest, up-to-date edition.
LIVE WORKING - VOLTAGE DETECTORS - PART 3: TWO-POLE LOW-VOLTAGE TYPE
Hardcopy , PDF
English
01-01-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Tests
6 Conformity assessment
7 Modifications
Annex A (informative) - Differences with IEC 61010
series
Annex B (normative) - Supplementary functions Phase
indication - Rotating field indication -
Continuity check
Annex C (normative) - Instructions for use
Annex D (normative) - General type test procedure
Annex E (normative) - Classification of defects and
associated requirements and tests
Annex F (informative) - In-service care and use
Annex G (informative) - Voltage detectors and the presence
of interference voltages
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Pertains to hand-held two-pole voltage detectors with their accessories (crocodile clips and detachable leads) to be used in contact with parts of electrical systems: - for a.c. voltages not exceeding 1000 V at nominal frequencies between 16 2/3 Hz and up to 500 Hz, and/or - for d.c. voltages not exceeding 1500 V.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
168
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| BS EN 61243-3:2014 | Identical |
| NBN EN 61243-3 : 2015 COR 2 2015 | Identical |
| EN 61243-3:2014/AC:2015 | Identical |
| UNE-EN 61243-3:2015 | Identical |
| DIN EN 61243-3 : 2015 | Identical |
| NF EN 61243-3 : 2015 | Identical |
| EN 61243-3:2014 | Identical |
| SN EN 61243-3:2014 | Identical |
| IEC 61477:2009 | Live working - Minimum requirements for the utilization of tools, devices and equipment |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| EN 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
| IEC TS 60479-1:2005+AMD1:2016 CSV | Effects of current on human beings and livestock - Part 1: Generalaspects |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO 354:2003 | Acoustics — Measurement of sound absorption in a reverberation room |
| IEC 60050-601:1985 | International Electrotechnical Vocabulary (IEV) - Part 601: Generation, transmission and distribution of electricity - General |
| EN 60695-10-2:2014 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| IEC 60304:1982 | Standard colours for insulation for low-frequency cables and wires |
| IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
| IEC 60942:2003 | Electroacoustics - Sound calibrators |
| IEC 60050-441:1984 | International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses |
| IEC 60743:2013 | Live working - Terminology for tools, devices and equipment |
| IEC 60068-2-31:2008 | Environmental testing - Part 2-31: Tests - Test Ec: Rough handling shocks, primarily for equipment-type specimens |
| EN 61318:2008 | Live working - Conformity assessment applicable to tools, devices and equipment |
| EN 60112 : 2003 AMD 1 2009 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| EN 61326-1:2013 | Electrical equipment for measurement, control and laboratory use - EMC requirements - Part 1: General requirements |
| IEC 60721-2-1:2013 | Classification of environmental conditions - Part 2-1: Environmental conditions appearing in nature - Temperature and humidity |
| IEC 61180-2:1994 | High-voltage test techniques for low-voltage equipment - Part 2: Test equipment |
| ISO/IEC Guide 51:2014 | Safety aspects — Guidelines for their inclusion in standards |
| EN ISO 354:2003 | Acoustics - Measurement of sound absorption in a reverberation room (ISO 354:2003) |
| EN 61672-1:2013 | Electroacoustics - Sound level meters - Part 1: Specifications |
| EN 61477:2009/corrigendum:2010 | LIVE WORKING - MINIMUM REQUIREMENTS FOR THE UTILIZATION OF TOOLS, DEVICES AND EQUIPMENT |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN 61010-031:2015 | Safety requirements for electrical equipment for measurement, control and laboratory use - Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| IEC GUIDE 104:2010 | The preparation of safety publications and the use of basic safety publications and group safety publications |
| IEC 61318:2007 | Live working - Conformity assessment applicable to tools, devices and equipment |
| EN 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| HD 402 : 200S2 | STANDARD COLOURS FOR INSULATION FOR LOW-FREQUENCY CABLES AND WIRES |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| IEC 60068-2-75:2014 | Environmental testing - Part 2-75: Tests - Test Eh: Hammer tests |
| IEC 60664-3:2016 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| IEC 61010-031:2015 RLV | Safety requirements for electrical equipment for measurement, control and laboratory use - Part 031: Safety requirements for hand-held probe assemblies for electrical measurement and test |
| EN 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| IEC 60050-651:2014 | International Electrotechnical Vocabulary (IEV) - Part 651: Live working |
| IEC 60695-10-2:2014 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| IEC 61180-1:1992 | High-voltage test techniques for low voltage equipment - Part 1: Definitions, test and procedure requirements |
| IEC 61557-7:2007 | Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 7: Phase sequence |
| EN 61010-1:2010 | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| ISO 3745:2012 | Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Precision methods for anechoic rooms and hemi-anechoic rooms |
| IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| EN 61557-7:2007 | Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 7: Phase sequence |
| IEC 61260:1995 | Electroacoustics - Octave-band and fractional-octave-band filters |
| EN 60942:2003 | Electroacoustics - Sound calibrators |
| IEC 61010-1:2010+AMD1:2016 CSV | Safety requirements for electrical equipment for measurement, control, and laboratory use - Part 1: General requirements |
| EN 61180-2:1994 | High-voltage test techniques for low-voltage equipment - Part 2: Test equipment |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| EN 60664-3:2017 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| EN 61260:1995/A1:2001 | ELECTROACOUSTICS - OCTAVE-BAND AND FRACTIONAL-OCTAVE-BAND FILTERS |
| EN 61180-1:1994 | High-voltage test techniques for low-voltage equipment - Part 1: Definitions, test and procedure requirements |
| EN 60068-2-31:2008 | ENVIRONMENTAL TESTING - PART 2-31: TESTS - TEST EC: ROUGH HANDLING SHOCKS, PRIMARILY FOR EQUIPMENT-TYPE SPECIMENS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.