I.S. EN 60893-2:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INSULATING MATERIALS - INDUSTRIAL RIGID LAMINATED SHEETS BASED ON THERMOSETTING RESINS FOR ELECTRICAL PURPOSES - PART 2: METHODS OF TEST
Hardcopy , PDF
11-01-2024
English
01-01-2004
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Conditioning of test specimens
4 Dimensions
4.1 Thickness
4.2 Flatness
5 Mechanical tests
5.1 Flexural strength
5.2 Modulus of elasticity in flexure
5.3 Compressive strength
5.4 Impact strength
5.5 Shear strength parallel to laminations
5.6 Tensile strength
6 Electrical tests
6.1 Electric strength and breakdown voltage
6.2 Permittivity and dissipation factor
6.3 Insulation resistance after immersion in water
6.4 Comparative and proof tracking indices
6.5 Tracking and erosion resistance
7 Thermal tests
7.1 Thermal endurance
7.2 Flammability
8 Other tests
8.1 Density
8.2 Water absorption
Annex A (informative) Modes of representation of capacitance
Annex B (informative) Liquids of known permittivity values
Annex ZA (normative) Normative references to international
publications with their corresponding
European publications
Bibliography
Explains methods of test for the materials defined in IEC 60893-1.
| DevelopmentNote |
For CENELEC adoptions of IEC publications, please check www.iec.ch to be sure that you have any corrigenda that may apply. (01/2017)
|
| DocumentType |
Standard
|
| Pages |
82
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 60893-2:2004 | Identical |
| UNE-EN 60893-2:2005 | Identical |
| SN EN 60893-2 : 1994 | Identical |
| NBN EN 60893-2 : 2005 | Identical |
| BS EN 60893-2:2004 | Identical |
| DIN EN 60893-2 : 2005 | Identical |
| IEC 60893-2:2003 | Identical |
| NF EN 60893-2 : 2004 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| EN ISO 62:2008 | Plastics - Determination of water absorption (ISO 62:2008) |
| EN 60216-1:2013 | Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results |
| IEC 60212:2010 | Standard conditions for use prior to and during the testing of solid electrical insulating materials |
| ISO 527-4:1997 | Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| EN ISO 527-4:1997 | Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotopic fibre-reinforced plastic composites (ISO 527-4:1997) |
| HD 437 : 200S1 | STANDARD CONDITIONS FOR USE PRIOR TO AND DURING THE TESTING OF SOLID ELECTRICAL INSULATING MATERIALS |
| IEC 60893-1:2004 | Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements |
| EN ISO 604:2003 | Plastics - Determination of compressive properties (ISO 604:2002) |
| EN ISO 179-1:2010 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
| EN 60112 : 2003 AMD 1 2009 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| IEC 60167:1964 | Methods of test for the determination of the insulation resistance of solid insulating materials |
| ISO 1183:1987 | Plastics Methods for determining the density and relative density of non-cellular plastics |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| HD 568 : 200S1 | METHODS OF TEST FOR THE DETERMINATION OF THE INSULATION RESISTANCE OF SOLID INSULATING MATERIALS |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| IEC TR 60893-4:2014 | Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 4: Typical values |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| ISO 604:2002 | Plastics — Determination of compressive properties |
| EN 60243-1:2013 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013) |
| ISO 3611:2010 | Geometrical product specifications (GPS) — Dimensional measuring equipment: Micrometers for external measurements — Design and metrological characteristics |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 62:2008 | Plastics Determination of water absorption |
| HD 380 : 200S2 | TEST METHODS FOR EVALUATING RESISTANCE TO TRACKING AND EROSION OF ELECTRICAL INSULATING MATERIALS USED UNDER SEVERE AMBIENT CONDITIONS |
| IEC 60587:2007 | Electrical insulating materials used under severe ambient conditions - Test methods for evaluating resistance to tracking and erosion |
| ISO 178:2010 | Plastics Determination of flexural properties |
| IEC 60216-1:2013 | Electrical insulating materials - Thermal endurance properties - Part 1: Ageing procedures and evaluation of test results |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
| EN 60893-1:2004 | Insulating materials - Industrial rigid laminated sheets based on thermosetting resins for electrical purposes - Part 1: Definitions, designations and general requirements |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.