I.S. EN 1916:2002
Current
The latest, up-to-date edition.
CONCRETE PIPES AND FITTINGS, UNREINFORCED, STEEL FIBRE AND REINFORCED
Hardcopy , PDF
English
01-01-2002
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 General requirements
5 Special requirements
6 Test methods for finished products
7 Conformity evaluation
8 Marking
Annex A (normative) - Test and calculation methods for
joint seals
Annex B (normative) - Structural calculations relative
to pipe jacking
Annex C (normative) - Test method for crushing strength
Annex D (normative) - Test method for longitudinal bending
moment resistance
Annex E (normative) - Test methods for watertightness
Annex F (normative) - Test method for water absorption
Annex G (normative) - Manufacturer's quality assurance system
Annex H (normative) - Sampling procedures for inspection of
finished products
Annex I (normative) - Sampling procedures for continuous
inspection of crushing strength and watertightness
(hydrostatic)
Annex J (normative) - Tasks for a product certification body
Annex K (normative) - Procedure for unreinforced concrete
pipes where routine (continuous) inspection of
crushing strength is primarily to minimum crushing load
Annex ZA (informative) - Clauses of this European Standard
addressing essential requirements or other provisions
of EU Directives
Bibliography
Defines performance requirements and test methods for precast concrete pipes and fittings, unreinforced, steel fibre and reinforced, with flexible joints (with seals either integrated in the units or supplied separately) and nominal sizes not exceeding DN 1750 for units with a circular bore or WN/HN 1200/1800 for units with an egg-shaped bore, for which the main intended use is the conveyance of sewage, rainwater and surface water under gravity or occasionally at low head of pressure, in pipelines that are generally buried.
| DocumentType |
Standard
|
| Pages |
117
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| BS EN 1916:2002 | Identical |
| NF EN 1916 : 2003 | Identical |
| EN 1916:2002 | Equivalent |
| BS EN 1916:2002 | Equivalent |
| NBN EN 1916 : 2002 COR 2008 | Identical |
| DIN EN 1916:2003-04 | Identical |
| NEN EN 1916 : 2002 C3 2008 | Identical |
| NS EN 1916 : 2002 AC 2008 | Identical |
| UNE-EN 1916:2008 | Identical |
| I.S. 6:2004 | CONCRETE SEWER PIPES |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| ISO/IEC Guide 62:1996 | General requirements for bodies operating assessment and certification/registration of quality systems |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| ISO 12491:1997 | Statistical methods for quality control of building materials and components |
| EN ISO 4288:1997 | Geometrical product specifications (GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture (ISO 4288:1996) |
| ISO 3951:1989 | Sampling procedures and charts for inspection by variables for percent nonconforming |
| EN 45011:1998 | General requirements for bodies operating product certification systems (ISO/IEC Guide 65:1996) |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| ISO 3384:2005 | Rubber, vulcanized or thermoplastic — Determination of stress relaxation in compression at ambient and at elevated temperatures |
| ISO 9001:2015 | Quality management systems — Requirements |
| ISO 4012:1978 | Concrete — Determination of compressive strength of test specimens |
| ISO 10544:1992 | Cold-reduced steel wire for the reinforcement of concrete and the manufacture of welded fabric |
| ISO/IEC Guide 65:1996 | General requirements for bodies operating product certification systems |
| EN 45012 : 1998 | GENERAL REQUIREMENTS FOR BODIES OPERATING ASSESSMENT AND CERTIFICATION/REGISTRATION OF QUALITY SYSTEMS |
Access your standards online with a subscription
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.
Important note : All end users must be registered with an Account prior to user licenses being assigned.