I.S. EN 1501-5:2011
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
REFUSE COLLECTION VEHICLES - GENERAL REQUIREMENTS AND SAFETY REQUIREMENTS - PART 5: LIFTING DEVICES FOR REFUSE COLLECTION VEHICLES
Available format(s)
Hardcopy , PDF
Superseded date
29-04-2021
Superseded by
Language(s)
English
Published date
01-01-2011
Publisher
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
6 Verification
7 Information for use
Annex A (normative) - Functional spaces, dimensions
and connections
Annex B (informative) - Types of special containers
and their pick-up systems
Annex C (normative) - Requirements for pin connections
and data sheets
Annex ZA (informative) - Relationship between this
Standard and the Essential Requirements of
EU Directive 2006/42/EC
Bibliography
Includes all significant hazards, hazardous situations and events relevant to lifting devices used for the emptying of designated waste containers into RCVs and their fitting onto the RCVs when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer throughout their foreseeable lifetime.
| DocumentType |
Standard
|
| Pages |
90
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 1501-5:2011 | Identical |
| ISO 13855:2010 | Safety of machinery Positioning of safeguards with respect to the approach speeds of parts of the human body |
| CEN Guide 414:2017 | Safety of machinery - Rules for the drafting and presentation of safety standards |
| EN 374-1:2003 | Protective gloves against chemicals and micro-organisms - Part 1: Terminology and performance requirements |
| EN 1501-2:2005+A1:2009 | Refuse collection vehicles and associated lifting devices - General requirements and safety requirements - Part 2: Side loaded refuse collection vehicles |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 13557:2003+A2:2008 | Cranes - Controls and control stations |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| EN 12574-1:2017 | Stationary waste containers - Part 1: Containers with a capacity up to 10 000 l with flat or dome lid(s), for trunnion, double trunnion or pocket lifting device - Dimensions and design |
| IEC 61984:2008 | Connectors - Safety requirements and tests |
| EN 13155:2003+A2:2009 | Cranes - Safety - Non-fixed load lifting attachments |
| EN 840-4:2012 | Mobile waste and recycling containers - Part 4: Containers with 4 wheels with a capacity up to 1 700 l with flat lid(s), for wide trunnion or BG- and/or wide comb lifting devices - Dimensions and design |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| ISO 15817:2012 | Earth-moving machinery — Safety requirements for remote operator control systems |
| EN 840-3:2012 | Mobile waste and recycling containers - Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices - Dimensions and design |
| EN 1501-4:2007 | Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 4: Noise test code for refuse collection vehicles |
| EN 61131-2:2007 | Programmable controllers - Part 2: Equipment requirements and tests |
| ISO 4413:2010 | Hydraulic fluid power General rules and safety requirements for systems and their components |
| EN ISO 14121-1:2007 | Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007) |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| EN 13135-2:2004+A1:2010 | Cranes - Equipment - Part 2: Non-electrotechnical equipment |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN 1501-3:2008 | Refuse collection vehicles and their associated lifting devices - General requirements and safety requirements - Part 3: Front loaded refuse collection vehicles |
| EN ISO 13857:2008 | Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| ISO 14121-1:2007 | Safety of machinery Risk assessment Part 1: Principles |
| ISO 11898-2:2016 | Road vehicles — Controller area network (CAN) — Part 2: High-speed medium access unit |
| EN 574:1996+A1:2008 | Safety of machinery - Two-hand control devices - Functional aspects - Principles for design |
| EN 1501-1:2011+A1:2015 | Refuse collection vehicles - General requirements and safety requirements - Part 1: Rear loaded refuse collection vehicles |
| EN 840-1:2012 | Mobile waste and recycling containers - Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices - Dimensions and design |
| EN ISO 13855:2010 | Safety of machinery - Positioning of safeguards with respect to the approach speeds of parts of the human body (ISO 13855:2010) |
| EN 13071-3:2011 | Stationary waste containers up to 5 000 l, top lifted and bottom emptied - Part 3: Recommended lifting connections |
| EN 13135-1:2003+A1:2010 | Cranes - Equipment - Part 1: Electrotechnical equipment |
| ISO 11898-1:2015 | Road vehicles — Controller area network (CAN) — Part 1: Data link layer and physical signalling |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 13309:2010 | Construction machinery - Electromagnetic compatibility of machines with internal power supply |
| EN ISO 4414:2010 | Pneumatic fluid power - General rules and safety requirements for systems and their components (ISO 4414:2010) |
| ISO 13849-2:2012 | Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
| ISO 13857:2008 | Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| ISO 11898-4:2004 | Road vehicles — Controller area network (CAN) — Part 4: Time-triggered communication |
| ISO 11898-3:2006 | Road vehicles Controller area network (CAN) Part 3: Low-speed, fault-tolerant, medium-dependent interface |
| EN ISO 13849-2:2012 | Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012) |
| EN ISO 6743-4:2015 | Lubricants, industrial oils and related products (class L) - Classification - Part 4: Family H (Hydraulic systems) (ISO 6743-4:2015) |
| IEC 61131-2:2017 | Industrial-process measurement and control - Programmable controllers - Part 2: Equipment requirements and tests |
| EN ISO 13849-1:2015 | Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015) |
| ISO 4414:2010 | Pneumatic fluid power General rules and safety requirements for systems and their components |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN 14803:2006 | Identification and/or determination of the quantity of waste |
| EN 840-2:2012 | Mobile waste and recycling containers - Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices - Dimensions and design |
| EN 61984:2009 | Connectors - Safety requirements and tests |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| EN ISO 4413:2010 | Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010) |
| ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
| ISO 3448:1992 | Industrial liquid lubricants — ISO viscosity classification |
| EN 840-5:2012 | Mobile waste and recycling containers - Part 5: Performance requirements and test methods |
| ISO 6743-4:2015 | Lubricants, industrial oils and related products (class L) Classification Part 4: Family H (Hydraulic systems) |
| ISO 7241-1:1987 | Hydraulic fluid power Quick-action couplings Part 1: Dimensions and requirements |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| ISO 11898-5:2007 | Road vehicles Controller area network (CAN) Part 5: High-speed medium access unit with low-power mode |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.