I.S. EN 14886:2008
Current
The latest, up-to-date edition.
PLASTICS AND RUBBER MACHINES - BANDKNIFE CUTTING MACHINES FOR BLOCK FOAMS - SAFETY REQUIREMENTS
Hardcopy , PDF
English
01-01-2008
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
4.1 General hazards on bandknife cutting machines
4.1.1 General
4.1.2 Mechanical hazards
4.1.3 Electrical hazards
4.1.4 Hazards due to failure of the control system
4.1.5 Hazards generated by noise
4.1.6 Fire hazard generated by flying sparks while grinding
the bandknife
4.1.7 Hazard due to inhalation of harmful dusts created by
cutting
4.2 Additional hazards or general hazards which require particular
protective measures on manual bandknife cutting machines
4.2.1 Vertical bandknife cutting machines
4.2.2 Tilting bandknife cutting machines
4.3 Additional hazards or general hazards which require particular
protective measures on automatic bandknife cutting machines
4.3.1 Bandknife cutting machines with turntable (carousel)
4.3.2 Vertical bandknife cutting machines with fixed table
and movable cutting unit
4.3.3 Horizontal bandknife cutting machines
4.3.4 Horizontal bandknife cutting machines for block trimming
4.3.5 Vertical bandknife cutting machines for block trimming
4.3.6 Contour cutting machines
4.3.7 Profile cutting and splitting machines
4.3.8 Compression cutting machines
4.3.9 Peeling machines
4.3.10 Cross-cutting machines
5 Safety requirements and/or protective measures
5.1 General requirements and/or measures for bandknife cutting
machines
5.1.1 General
5.1.2 Mechanical hazards
5.1.3 Electrical hazards
5.1.4 Hazards due to failure of the control system
5.1.5 Hazards generated by noise
5.1.6 Fire hazard generated by flying sparks while grinding
the bandknife
5.1.7 Hazard due to inhalation of harmful dusts created by
cutting
5.2 Additional requirements and/or measures for manual bandknife
cutting machines
5.2.1 Vertical bandknife cutting machines
5.2.2 Tilting bandknife cutting machines
5.3 Additional requirements and/or measures for automatic
bandknife cutting machines
5.3.1 Bandknife cutting machines with turntable (carousel)
5.3.2 Vertical bandknife cutting machines with fixed table
and movable cutting unit
5.3.3 Horizontal bandknife cutting machines
5.3.4 Horizontal bandknife cutting machines for block trimming
5.3.5 Vertical bandknife cutting machines for block trimming
5.3.6 Contour cutting machines
5.3.7 Profile cutting and splitting machines
5.3.8 Compression cutting machines
5.3.9 Peeling machines
5.3.10 Cross-cutting machines
6 Verification of safety requirements and/or protective measures
7 Information for use
7.1 Instruction handbook
7.1.1 General
7.1.2 General information for all bandknife cutting machines
7.1.3 Additional information for particular bandknife cutting
machines
7.2 Marking
Annex A (normative) Noise test code
A.1 Introduction
A.2 Determination of the A-weighted emission sound pressure
level at the operator's position
A.3 Determination of the A-weighted sound power level
A.4 Installation and mounting conditions for noise measurement
A.5 Operating conditions
A.6 Measurement uncertainty
A.7 Information to be recorded and reported
A.7.1 Information to be recorded
A.7.2 Information to be reported
A.8 Declaration and verification of noise emission values
Annex B (normative) Prohibition sign: "No access"
Annex ZA (informative) Relationship between this European Standard
and the Essential Requirements of EU Directive
98/37/EC
Annex ZB (informative) Relationship between this European Standard
and the Essential Requirements of EU Directive
2006/42/EC
Bibliography
Applicable to machines that are designed specifically to cut, split or peel block foams to commercially required shapes, using a single or double cut.
| DocumentType |
Standard
|
| Pages |
83
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Current
|
| Standards | Relationship |
| NEN EN 14886 : 2008 | Identical |
| EN 14886:2008 | Identical |
| UNI EN 14886 : 2008 | Identical |
| NF EN 14886 : 2008 | Identical |
| BS EN 14886:2008 | Identical |
| DIN EN 14886:2008-06 | Identical |
| EN 13236:2010+A1:2015 | Safety requirements for superabrasive products |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| ISO 11202:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| ISO 4871:1996 | Acoustics — Declaration and verification of noise emission values of machinery and equipment |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| EN 12413:2007+A1:2011 | Safety requirements for bonded abrasive products |
| IEC 61310-2:2007 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| ISO/TR 11688-1:1995 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| EN 61310-2:2008 | Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking |
| EN 811 : 1996 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE LOWER LIMBS |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
| EN ISO 13850:2015 | Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015) |
| EN ISO 11688-2:2000 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 2: Introduction to the physics of low-noise design (ISO/TR 11688-2:1998) |
| EN ISO 11201:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010) |
| ISO 3746:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| EN 61496-1:2013/AC:2015 | SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012) |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| ISO 12100-2:2003 | Safety of machinery Basic concepts, general principles for design Part 2: Technical principles |
| IEC 61496-1:2012 | Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests |
| EN 954-1 : 1996 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
| ISO 12100-1:2003 | Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology |
| ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| IEC 61310-1:2007 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN 1760-2:2001+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars |
| EN 1760-3:2004+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 3: General principles for the design and testing of pressure sensitive bumpers, plates, wires and similar devices |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| ISO/TR 11688-2:1998 | Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| ISO 11201:2010 | Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.