I.S. EN 13476-3:2007
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY (VINYL CHLORIDE) (PVC-U), POLYPROPYLENE (PP) AND POLYETHYLENE (PE) - PART 3: SPECIFICATIONS FOR PIPES AND FITTINGS WITH SMOOTH INTERNAL AND PROFILED EXTERNAL SURFACE AND THE SYSTEM, TYPE B
Available format(s)
Hardcopy , PDF
Superseded date
03-07-2020
Language(s)
English
Published date
01-01-2007
Publisher
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National Foreword
European foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Material
5 Designation of wall constructions and examples of typical
jointing methods
6 Appearance and colour
7 Geometrical characteristics
8 Physical characteristics
9 Mechanical characteristics
10 Performance requirements
11 Marking
Annex A (normative) - Compound/formulation PVC-U material
Annex B (normative) - Utilization of non-virgin PVC-U material
Annex C (normative) - Compound/Formulation PP material
Annex D (normative) - Utilization of non-virgin PP material
Annex E (normative) - Compound/Formulation PE material
Annex F (normative) - Utilization of non-virgin PE material
Annex G (normative) - Impact test at 23 degree C
Annex H (normative) - Impact test at -10 degree C
Annex I (normative) - Ring flexibility test at 20% diametric
deflection
Annex J (informative) - Survey of possible use of
reprocessed and recycled material
Annex K (normative) - Impact test for large diameter pipes
with structured wall
Bibliography
Describes the definitions and requirements for pipes, fittings and the system based on unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) structured-wall piping systems that are intended to be used for non-pressure underground drainage and sewerage systems.
| DocumentType |
Standard
|
| Pages |
48
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| Standards | Relationship |
| SN EN 13476-3 : 2007 + A1 2009 | Identical |
| ONORM EN 13476-3 : 2015 | Identical |
| NF EN 13476-3 : 2007 + A1 2009 | Identical |
| NS EN 13476-3 : 2007 + A1 2009 | Identical |
| UNI EN 13476-3 : 2009 | Identical |
| DIN EN 13476-3:2015-11 (Draft) | Identical |
| BS EN 13476-3 : 2007 | Identical |
| UNE-EN 13476-3:2007 | Identical |
| NBN EN 13476-3 : 2007 + A1 2009 | Identical |
| EN 13476-3:2018 | Identical |
| NEN EN 13476-3 : 2018 | Identical |
| ISO 580:2005 | Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating |
| EN ISO 3126:2005 | Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005) |
| ISO 2507-2:1995 | Thermoplastics pipes and fittings — Vicat softening temperature — Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and for high impact resistance poly (vinyl chloride) (PVC-HI) pipes |
| ISO 6259-2:1997 | Thermoplastics pipes Determination of tensile properties Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride) (PVC-HI) |
| EN ISO 13229:2011 | Thermoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value (ISO 13229:2010) |
| ISO 13259:2010 | Thermoplastics piping systems for underground non-pressure applications Test method for leaktightness of elastomeric sealing ring type joints |
| ISO 3451-1:2008 | Plastics Determination of ash Part 1: General methods |
| ISO 13229:2010 | Thermoplastics piping systems for non-pressure applications Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings Determination of the viscosity number and K-value |
| ISO 12091:1995 | Structured-wall thermoplastics pipes Oven test |
| EN ISO 9967:2016 | Thermoplastics pipes - Determination of creep ratio (ISO 9967:2016) |
| ISO 13263:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for impact strength |
| EN ISO 1158:1998 | Plastics - Vinyl chloride homopolymers and copolymers - Determination of chlorine content (ISO 1158:1998) |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 1133-1:2011 | Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method |
| ISO 11173:1994 | Thermoplastics pipes — Determination of resistance to external blows — Staircase method |
| ISO 2507-1:1995 | Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method |
| ISO 13265:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage — Joints for buried non-pressure applications — Test method for the long-term sealing performance of joints with elastomeric seals by estimating the sealing pressure |
| EN ISO 11173:2017 | Thermoplastics pipes - Determination of resistance to external blows - Staircase method (ISO 11173:1994) |
| ISO 3127:1994 | Thermoplastics pipes — Determination of resistance to external blows — Round-the-clock method |
| EN ISO 3451-1:2008 | Plastics - Determination of ash - Part 1: General methods (ISO 3451-1:2008) |
| EN ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) |
| EN 15346:2014 | Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates |
| EN ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006) |
| ISO 13968:2008 | Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility |
| EN ISO 6259-1:2015 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015) |
| EN 14680:2015 | Adhesives for non-pressure thermoplastics piping systems - Specifications |
| ISO 6259-1:2015 | Thermoplastics pipes Determination of tensile properties Part 1: General test method |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| EN ISO 9852:2017 | Unplasticized poly(vinyl chloride) (PVC-U) pipes - Dichloromethane resistance at specified temperature (DCMT) - Test method (ISO 9852:2007) |
| EN 476:2011 | General requirements for components used in drains and sewers |
| EN ISO 1133-1:2011 | Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011) |
| ISO 13260:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage Test method for resistance to combined temperature cycling and external loading |
| ISO 13262:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics spirally-formed structured-wall pipes Determination of the tensile strength of a seam |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN ISO 3127:2017 | Thermoplastics pipes - Determination of resistance to external blows - Round-the-clock method (ISO 3127:1994) |
| EN 14758-1:2012 | Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene with mineral modifiers (PP-MD) - Part 1: Specifications for pipes, fittings and the system |
| ISO 18373-1:2007 | Rigid PVC pipes Differential scanning calorimetry (DSC) method Part 1: Measurement of the processing temperature |
| ISO 1158:1998 | Plastics — Vinyl chloride homopolymers and copolymers — Determination of chlorine content |
| EN ISO 13968:2008 | Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility (ISO 13968:2008) |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| EN ISO 13967:2009 | Thermoplastics fittings - Determination of ring stiffness (ISO 13967:2009) |
| EN 12666-1:2005+A1:2011 | Plastics piping systems for non-pressure underground drainage and sewerage - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system |
| EN ISO 9969:2016 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016) |
| EN ISO 13262:2017 | Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam (ISO 13262:2010) |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 580:2005 | Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005) |
| EN ISO 13254:2017 | Thermoplastics piping systems for non-pressure applications - Test method for watertightness (ISO 13254:2010) |
| EN 1401-1:2009 | Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 9967:2016 | Thermoplastics pipes Determination of creep ratio |
| EN ISO 2505:2005 | Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005) |
| ISO 13967:2009 | Thermoplastics fittings Determination of ring stiffness |
| ISO 13257:2010 | Thermoplastics piping systems for non-pressure applications Test method for resistance to elevated temperature cycling |
| EN ISO 13257:2017 | Thermoplastics piping systems for non-pressure applications - Test method for resistance to elevated temperature cycling (ISO 13257:2010) |
| ISO 13254:2010 | Thermoplastics piping systems for non-pressure applications Test method for watertightness |
| ISO 13264:2010 | Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for mechanical strength or flexibility of fabricated fittings |
| ISO 9969:2016 | Thermoplastics pipes Determination of ring stiffness |
| EN 12099:1997 | Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
| ISO 9852:2007 | Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified temperature (DCMT) — Test method |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
| ISO 2505:2005 | Thermoplastics pipes — Longitudinal reversion — Test method and parameters |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.