I.S. EN 13411-5:2003
Withdrawn
A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.
TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 5: U-BOLT WIRE ROPE GRIPS
Hardcopy , PDF
18-12-2008
English
12-09-2003
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or measures
5.1 Materials
5.2 Mechanical properties
6 Verification of safety requirements
6.1 Qualification of personnel
6.2 Type testing
7 Information for use
7.1 Identification marking
7.2 Fitting instructions
7.3 Certificate
Annex A (informative) Specification for construction and sizes
for one design of grip - 1
A.1 General
A.2 Material
A.3 Dimensions
A.4 Fitting instructions
Annex B (informative) Specification for construction and sizes
for one design of grip - 2
B.1 General
B.2 Material
B.3 Dimensions
B.4 Fitting instructions
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
Gives the minimum requirements for U-bolt wire rope grips manufactured from ferrous materials and the safe behaviour of eye terminations secured by U-bolt wire rope grips for use as intended by the manufacturer.
| DevelopmentNote |
2003 Edition Re-Issued in December 2008 & incorporates AMD 1 2008. (01/2009)
|
| DocumentType |
Standard
|
| Pages |
23
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Withdrawn
|
| Standards | Relationship |
| UNE-EN 13411-5:2004 | Identical |
| BS EN 13411-5 : 2003 | Identical |
| NBN EN 13411-5 : 2003 + A1 2009 | Identical |
| NS EN 13411-5 : 2003 + A1 2008 | Identical |
| NF EN 13411-5 : 2003 + A1 2008 | Identical |
| UNI EN 13411-5 : 2009 | Identical |
| EN 13411-5:2003+A1:2008 | Identical |
| SN EN 13411-5 : 2003 + A1 2009 | Identical |
| NEN EN 13411-5 : 2003 + A1 2008 | Identical |
| DIN EN 13411-5:2009-02 | Identical |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| EN 12385-2:2002+A1:2008 | Steel wire ropes - Safety - Part 2: Definitions, designation and classification |
| EN 12385-1:2002+A1:2008 | Steel wire ropes - Safety - Part 1: General requirements |
| ISO 4042:1999 | Fasteners Electroplated coatings |
| EN ISO 4042:1999 | Fasteners - Electroplated coatings (ISO 4042:1999) |
| ISO 4759-1:2000 | Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C |
| EN 1562:2012 | Founding - Malleable cast irons |
| ISO 5922:2005 | Malleable cast iron |
| EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| ASTM A 563 : 2015 : REDLINE | Standard Specification for Carbon and Alloy Steel Nuts |
| EN 1677-1:2000+A1:2008 | Components for slings - Safety - Part 1: Forged steel components, Grade 8 |
| EN ISO 4759-1:2000 | Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts - Product grades A, B and C (ISO 4759-1:2000) |
| EN 22768-1:1993 | General tolerances - Part 1: Tolerances for linear and angular dimensions without individual tolerance indications (ISO 2768-1:1989) |
| EN 12329 : 2000 | CORROSION PROTECTION OF METALS - ELECTRODEPOSITED COATINGS OF ZINC WITH SUPPLEMENTARY TREATMENT ON IRON OR STEEL |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| ISO 7500-1:2015 | Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system |
| EN 292-2 : 91 AMD 1 95 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION |
| ISO 8062:1994 | Castings System of dimensional tolerances and machining allowances |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.