I.S. EN 10329:2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
STEEL TUBES AND FITTINGS FOR ONSHORE AND OFFSHORE PIPELINES - EXTERNAL FIELD JOINT COATINGS
Hardcopy , PDF
03-04-2016
English
01-01-2006
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Information to be supplied by the purchaser
4.1 Mandatory
4.2 Options to be indicated by the purchaser
5 Choice of coatings
5.1 Types of coating
5.2 Types of joint coatings depending on factory applied
tube coating
5.3 Documents
6 Application of the coating and general requirements
6.1 Preparation of the surface before coating
6.2 Conditions before application
6.3 Appearance of the coating
6.4 Testing
6.5 Additional mechanical protection
6.6 Repair
6.7 Qualification of the application procedure and the coater
6.8 Preliminary quality inspection
7 Coatings
7.1 Bituminous tapes, petrolatum tapes, plastic tapes or heat
shrinkable materials
7.2 Liquid epoxy resin or liquid polyurethane
7.3 Polypropylene
7.4 Epoxy powder
Annex A (normative) Inspection of thickness
A.1 General
A.2 Apparatus
A.3 Procedure
A.4 Results
Annex B (normative) Holiday detection test
B.1 General
B.2 Apparatus
B.3 Procedure
B.4 Results
Annex C (normative) Adhesion test - Resistance to removal
C.1 General
C.2 Apparatus
C.3 Procedure
C.4 Results
Annex D (normative) Peel strength test
D.1 Measurement of the peel strength on a coated sample
D.2 Measurement of the peel strength on large diameter
joint
D.3 Measurement of the peel strength with a spring balance
Annex E (normative) Test for assessing the degree of cure of the
epoxy coating by thermal analysis
E.1 General
E.2 Principle
E.3 Sampling
E.4 Procedure
E.5 Results
Annex F (normative) Cathodic disbondment test
F.1 General
F.2 Apparatus
F.3 Sampling
F.4 Procedure
F.5 Investigation procedure
F.6 Results
Annex G (normative) Impact test
G.1 General
G.2 Apparatus
G.3 Procedure
G.4 Results
Annex H (normative) Indentation test
H.1 General
H.2 Apparatus
H.3 Procedure
H.4 Results
Annex I (informative) Qualification of the application procedure
and the coater
I.1 General
I.2 Qualification of the procedure and the coater
I.3 Frequency of inspections
I.4 Retest
Bibliography
Describes the application and related testing of the corrosion protection coatings applied to steel surfaces left bare after the tubes and fittings (components) are joined by welding.
| DocumentType |
Standard
|
| Pages |
47
|
| PublisherName |
National Standards Authority of Ireland
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| EN 10329:2006 | Identical |
| UNI EN 10329 : 2006 | Identical |
| BS EN 10329 : 2005 | Identical |
| NS EN 10329 : 1ED 2006 | Identical |
| UNE-EN 10329:2008 | Identical |
| NEN EN 10329 : 2006 | Identical |
| NF EN 10329 : 2006 | Identical |
| SN EN 10329 : 2006 | Identical |
| NBN EN 10329 : 2006 | Identical |
| DIN EN 10329:2006-04 | Identical |
| ISO 2811-1:2016 | Paints and varnishes — Determination of density — Part 1: Pycnometer method |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| EN 10290:2002 | Steel tubes and fittings for onshore and offshore pipelines - External liquid applied polyurethane and polyurethane-modified coatings |
| EN 10288:2002 | Steel tubes and fittings for onshore and offshore pipelines - External two layer extruded polyethylene based coatings |
| ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings |
| ISO 2808:2007 | Paints and varnishes Determination of film thickness |
| EN 10289:2002 | Steel tubes and fittings for onshore and offshore pipelines - External liquid applied epoxy and epoxy-modified coatings |
| EN ISO 2811-1:2016 | Paints and varnishes - Determination of density - Part 1: Pycnometer method (ISO 2811-1:2016) |
| ISO 11357-2:2013 | Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height |
| EN ISO 8503-1:2012 | Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces (ISO 8503-1:2012) |
| ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 2815:2003 | Paints and varnishes Buchholz indentation test |
| EN 12068:1998 | Cold-rolled flat products made of high yield strength micro-alloyed steels for cold forming - General delivery conditions |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| EN ISO 2815:2003 | Paints and varnishes - Buchholz indentation test (ISO 2815:2003) |
| ISO 8503-1:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces |
| EN ISO 868:2003 | Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness) (ISO 868:2003) |
| EN ISO 8501-1:2007 | Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings (ISO 8501-1:2007) |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| EN 10310:2003 | Steel tubes and fittings for onshore and offshore pipelines - Internal and external polyamide powder based coatings |
| ISO 527-3:1995 | Plastics Determination of tensile properties Part 3: Test conditions for films and sheets |
| EN ISO 306:2013 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013) |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| EN ISO 2808:2007 | Paints and varnishes - Determination of film thickness (ISO 2808:2007) |
| ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.