EN ISO 21003-3:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Multilayer piping systems for hot and cold water installations inside buildings - Part 3: Fittings (ISO 21003-3:2008)
06-11-2021
01-07-2008
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Material characteristics
5.1 Plastics fitting materials specified in reference
product standards
5.2 Plastics fitting materials not specified in reference
product standards
5.3 Metallic fitting material
5.4 Influence on water intended for human consumption
6 General characteristics
6.1 Appearance
6.2 Opacity
7 Geometrical characteristics
7.1 General
7.2 Dimensions of sockets for socket weld, electrofusion
and solvent-cemented fittings
7.3 Dimensions of metallic fittings
8 Mechanical characteristics of plastics fittings (internal
pressure test)
8.1 General
8.2 Plastics fitting materials specified in reference
product standards
8.3 Plastics fitting materials not specified in reference
product standards
9 Physical and chemical characteristics of plastics fittings
9.1 Plastics fitting materials specified in reference
product standards
9.2 Plastics fitting materials not specified in reference
product standards
9.3 Sealing elements
10 Performance requirements
11 Marking
11.1 General requirements
11.2 Minimum required marking
Annex A (normative) - List of reference product standards
Bibliography
ISO 21003-3:2008 specifies the characteristics of fittings for multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or for heating systems — under specified design pressures and temperatures appropriate to the class of applicationIt also specifies the test parameters for the test methods referred to in this part of ISO 21003.ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. ISO 21003-3 is intended for use only in conjunction with all the other parts of ISO 21003.
| Committee |
CEN/TC 155
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| Standards | Relationship |
| UNE-EN ISO 21003-3:2009 | Identical |
| ONORM EN ISO 21003-3 : 2008 | Identical |
| UNI EN ISO 21003-3:2022 | Identical |
| I.S. EN ISO 21003-3:2008 | Identical |
| DIN EN ISO 21003-3:2008-11 | Identical |
| NF EN ISO 21003-3 : 2008 | Identical |
| UNI EN ISO 21003-3 : 2009 | Identical |
| NS EN ISO 21003-3 : 1ED 2008 | Identical |
| SS-EN ISO 21003-3 : 2008 | Identical |
| BS EN ISO 21003-3:2008 | Identical |
| NBN EN ISO 21003-3 : 2008 | Identical |
| PN EN ISO 21003-3 : 2009 | Identical |
| ISO 21003-3:2008 | Identical |
| NEN EN ISO 21003-3 : 2008 | Identical |
| SN EN ISO 21003-3:2008 | Identical |
| 11/30197617 DC : 0 | BS ISO 11855-5 - BUILDING ENVIRONMENT DESIGN - STANDARDS FOR THE DESIGN, CONSTRUCTION AND OPERATION OF RADIANT HEATING AND COOLING SYSTEMS - PART 5: INSTALLATION |
| 09/30202316 DC : 0 | BS EN 12514-4 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 4: SAFETY REQUIREMENTS AND TESTS - PIPINGS AND PARTS WITHIN PIPELINES |
| NF EN 1264-4 : 2010 | WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| I.S. EN 1264-4:2009 | WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| UNI EN 806-4 : 2010 | SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION |
| BS EN 806-4:2010 | Specifications for installations inside buildings conveying water for human consumption Installation |
| EN 1264-4:2009 | Water based surface embedded heating and cooling systems - Part 4: Installation |
| ISO/TS 21003-7:2008 | Multilayer piping systems for hot and cold water installations inside buildings Part 7: Guidance for the assessment of conformity |
| S.R. CEN ISO TS 21003-7:2008 | MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
| NF EN 806-4 : 2010 | SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION |
| DIN EN 1264-4:2009-11 | Water based surface embedded heating and cooling systems - Part 4: Installation |
| BS EN 1264-4:2009 | Water based surface embedded heating and cooling systems Installation |
| DIN EN 806-4:2010-06 | Specifications for installations inside buildings conveying water for human consumption - Part 4: Installation |
| DD CEN ISO/TS 21003-7 : 2008 | MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
| UNI EN 1264-4 : 2009 | WATER BASED SURFACE EMBEDDED HEATING AND COOLING SYSTEMS - PART 4: INSTALLATION |
| I.S. EN 806-4:2010 | SPECIFICATIONS FOR INSTALLATIONS INSIDE BUILDINGS CONVEYING WATER FOR HUMAN CONSUMPTION - PART 4: INSTALLATION |
| EN 806-4:2010 | Specifications for installations inside buildings conveying water for human consumption - Part 4: Installation |
| UNI CEN ISO/TS 21003-7 : 2010 | MULTILAYER PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS INSIDE BUILDINGS - PART 7: GUIDANCE FOR THE ASSESSMENT OF CONFORMITY |
| UNE-EN 1264-4:2010 | Water based surface embedded heating and cooling systems - Part 4: Installation |
| EN 1254-3:1998 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes |
| ISO 15874-3:2013 | Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 3: Fittings |
| ISO 15877-3:2009 | Plastics piping systems for hot and cold water installations — Chlorinated poly(vinyl chloride) (PVC-C) — Part 3: Fittings |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| BS 7291-2:2006 | Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for polybutylene (PB) pipes and associated fittings |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 21003-5:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 5: Fitness for purpose of the system |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 15876-3:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 3: Fittings |
| ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components |
| ISO 21003-2:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes |
| ISO 21003-1:2008 | Multilayer piping systems for hot and cold water installations inside buildings — Part 1: General |
| ISO 22391-3:2009 | Plastics piping systems for hot and cold water installations — Polyethylene of raised temperature resistance (PE-RT) — Part 3: Fittings |
| BS 7291-4:1990 | Thermoplastics pipes and associated fittings for hot and cold water for domestic purposes and heating installations in buildings Specification for chlorinated polyvinyl chloride (PVC-C) pipes and associated fittings and solvent cement |
| ISO/TS 21003-7:2008 | Multilayer piping systems for hot and cold water installations inside buildings Part 7: Guidance for the assessment of conformity |
| ISO 15875-3:2003 | Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 3: Fittings |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
| ISO 7686:2005 | Plastics pipes and fittings — Determination of opacity |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.