EN 62368-1:2014/AC:2017-03
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED)
Amendment of
Superseded date
16-02-2022
Superseded by
Published date
04-08-2014
Sorry this product is not available in your region.
INTRODUCTION
0 Principles of this product safety standard
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 General requirements
5 Electrically-caused injury
6 Electrically-caused fire
7 Injury caused by hazardous substances
8 Mechanically-caused injury
9 Thermal burn injury
10 Radiation
Annex A (informative) - Examples of equipment within
the scope of this standard
Annex B (normative) - Normal operating condition tests,
abnormal operating condition tests and single
fault condition tests
Annex C (normative) - UV radiation
Annex D (normative) - Test generators
Annex E (normative) - Test conditions for equipment containing
audio amplifiers
Annex F (normative) - Equipment markings, instructions, and
instructional safeguards
Annex G (normative) - Components
Annex H (normative) - Criteria for telephone ringing signals
Annex I (informative) - Overvoltage categories
Annex J (normative) - Insulated winding wires for use
without interleaved insulation
Annex K (normative) - Safety interlocks
Annex L (normative) - Disconnect devices
Annex M (normative) - Equipment containing batteries and
their protection circuits
Annex N (normative) - Electrochemical potentials (V)
Annex O (normative) - Measurement of creepage distances
and clearances
Annex P (normative) - Safeguards against conductive objects
Annex Q (normative) - Circuits intended for interconnection
with building wiring
Annex R (normative) - Limited short-circuit test
Annex S (normative) - Tests for resistance to heat and fire
Annex T (normative) - Mechanical strength tests
Annex U (normative) - Mechanical strength of CRTs and
protection against the effects of implosion
Annex V (normative) - Determination of accessible parts
Annex W (informative) - Comparison of terms introduced
in this standard
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
Annex ZB (normative) - Special National Conditions
Annex ZC (informative) - A-deviations
Annex ZD (informative) - IEC and CENELEC code designations
for flexible cords
Pertains to the safety of electrical and electronic equipment within the field of audio, video, information and communication technology, and business and office machines with a rated voltage not exceeding 600 V.
| Committee |
TC 108X
|
| DevelopmentNote |
Supersedes EN 60950-1. (06/2015) Supersedes EN 60065 which remains current and will be withdrawn on 20-06-2019. (04/2016)
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| DS EN 62368-1 : 2014 COR 2017 | Identical |
| VDE 0868-1 : 2016 AMD 11 2017 | Identical |
| CEI EN 62368-1 : 2016 | Identical |
| SN EN 62368-1:2014 | Identical |
| BS EN 62368-1 : 2014 | Identical |
| I.S. EN 62368-1:2014 | Identical |
| DIN EN 62368-1 : 2016 AMD 11 2017 | Identical |
| NEN EN IEC 62368-1 : 2014 C12 2017 | Identical |
| NBN EN 62368-1 : 2014 COR 2015 | Identical |
| NF EN 62368-1 : 2014 | Identical |
| UNE-EN 62368-1:2014/AC:2017-03 | Identical |
| PN EN 62368-1 : 2015 AC 2017 | Identical |
| EN 63002:2017 | Identification and communication interoperability method for external power supplies used with portable computing devices |
| EN 50332-3:2017 | Sound system equipment: headphones and earphones associated with personal music players - Maximum sound pressure level measurement methodology - Part 3: Measurement method for sound dose management |
| BS EN 60695-1-10:2017 | Fire hazard testing Guidance for assessing the fire hazard of electrotechnical products. General guidelines |
| EN 62949:2017 | Particular safety requirements for equipment to be connected to information and communication networks |
| BS EN 60065 : 2014 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014, MODIFIED) |
| EN 60950-22:2017 | Information technology equipment - Safety - Part 22: Equipment to be installed outdoors |
| EN 60695-1-10:2017 | Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines |
| EN 50332-2:2013 | Sound system equipment: Headphones and earphones associated with personal music players - Maximum sound pressure level measurement methodology - Part 2: Matching of sets with headphones if either or both are offered separately, or are offered as one package equipment but with standardised connectors between the two allowing to combine components of different manufacturers or different design |
| EN 300 132-1 : 2.0.1 DRAFT | ENVIRONMENTAL ENGINEERING (EE); POWER SUPPLY INTERFACE AT THE INPUT TO INFORMATION AND COMMUNICATION TECHNOLOGY (ICT) EQUIPMENT; PART 1: OPERATED BY ALTERNATING CURRENT (AC) SOURCE |
| PD CLC/TR 50656:2016 | SPD application in conjunction with Class II equipment |
| I.S. EN 62949:2017 | PARTICULAR SAFETY REQUIREMENTS FOR EQUIPMENT TO BE CONNECTED TO INFORMATION AND COMMUNICATION NETWORKS |
| 13/30281665 DC : 0 | BS EN 50332-2 - SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PORTABLE AUDIO EQUIPMENT - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY AND LIMIT CONSIDERATIONS - PART 2: MATCHING OF SETS WITH HEADPHONES IF EITHER OR BOTH ARE OFFERED SEPARATELY |
| BS EN 63002 : 2017 | IDENTIFICATION AND COMMUNICATION INTEROPERABILITY METHOD FOR EXTERNAL POWER SUPPLIES USED WITH PORTABLE COMPUTING DEVICES |
| BS EN 62949:2017 | Particular safety requirements for equipment to be connected to information and communication technology networks |
| BS EN 60940:2015 | Guidance information on the application of capacitors, resistors, inductors and complete filter units for electromagnetic interference suppression |
| EN IEC 61204-7:2018 | Low-voltage switch mode power supplies - Part 7: Safety requirements |
| I.S. EN 63002:2017 | IDENTIFICATION AND COMMUNICATION INTEROPERABILITY METHOD FOR EXTERNAL POWER SUPPLIES USED WITH PORTABLE COMPUTING DEVICES |
| I.S. EN 50131-1:2006 | ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 1: SYSTEM REQUIREMENTS |
| EN 60065:2014/AC:2017-01 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016) |
| 17/30350085 DC : DRAFT SEP 2017 | BS EN 50131-8 - ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 8: SECURITY FOG DEVICES |
| PREN 50332-2 : DRAFT 2013 | SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PORTABLE AUDIO EQUIPMENT - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY AND LIMIT CONSIDERATIONS - PART 2: MATCHING OF SETS WITH HEADPHONES IF EITHER OR BOTH ARE OFFERED SEPARATELY |
| BS EN 50332-3:2017 | Sound system equipment: headphones and earphones associated with personal music players. Maximum sound pressure level measurement methodology Measurement method for sound dose management |
| CEI EN 50332-3 : 1ED 2017 | SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PERSONAL MUSIC PLAYERS - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY - PART 3: MEASUREMENT METHOD FOR SOUND DOSE MANAGEMENT |
| I.S. EN 61643-11:2012 | LOW-VOLTAGE SURGE PROTECTIVE DEVICES - PART 11: SURGE PROTECTIVE DEVICES CONNECTED TO LOW-VOLTAGE POWER SYSTEMS - REQUIREMENTS AND TESTS METHODS |
| I.S. EN 50174-3:2013 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS |
| I.S. EN IEC 61204-7:2018 | LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS |
| I.S. EN 50332-3:2017 | SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PERSONAL MUSIC PLAYERS - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY - PART 3: MEASUREMENT METHOD FOR SOUND DOSE MANAGEMENT |
| EN 300 132-2 : 2.4.6 | ENVIRONMENTAL ENGINEERING (EE); POWER SUPPLY INTERFACE AT THE INPUT TO TELECOMMUNICATIONS AND DATACOM (ICT) EQUIPMENT; PART 2: OPERATED BY -48 V DIRECT CURRENT (DC) |
| UNE-EN 60065:2015 | Audio, video and similar electronic apparatus - Safety requirements |
| 16/30338723 DC : 0 | BS EN 61643-11:2012/A - LOW-VOLTAGE SURGE PROTECTIVE DEVICES - PART 11: SURGE PROTECTIVE DEVICES CONNECTED TO LOW-VOLTAGE POWER SYSTEMS - REQUIREMENTS AND TEST METHODS |
| BS EN 62911:2016 | Audio, video and information technology equipment. Routine electrical safety testing in production |
| BS EN 50332-2:2013 | Sound system equipment: Headphones and earphones associated with personal music players. Maximum sound pressure level measurement methodology Matching of sets with headphones if either or both are offered separately, or are offered as one package equipment but with standardised connectors between the two allowing to combine components of different manufacturers or different design |
| BS EN 60950-22:2017 | Information technology equipment. Safety Equipment to be installed outdoors |
| I.S. EN 60065:2014 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS |
| I.S. EN 62911:2016 | AUDIO, VIDEO AND INFORMATION TECHNOLOGY EQUIPMENT - ROUTINE ELECTRICAL SAFETY TESTING IN PRODUCTION |
| EN 50174-3:2013/A1:2017 | INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 3: INSTALLATION PLANNING AND PRACTICES OUTSIDE BUILDINGS |
| PREN 50131-8 : DRAFT 2017 | ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 8: SECURITY FOG DEVICES |
| 17/30361391 DC : 0 | BS EN 50174-2 - INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS |
| EN 62911:2016 | Audio, video and information technology equipment - Routine electrical safety testing in production |
| UNE-EN 60695-1-10:2017 | Fire hazard testing - Part 1-10: Guidance for assessing the fire hazard of electrotechnical products - General guidelines |
| TS 102 121 : 1.3.1 | ENVIRONMENTAL ENGINEERING (EE); POWER DISTRIBUTION TO TELECOMMUNICATIONS AND DATACOM (ICT) EQUIPMENT |
| CLC/TR 50656:2016 | SPD application in conjunction with Class II equipment |
| CEI EN 62949 : 1ED 2017 | PARTICULAR SAFETY REQUIREMENTS FOR EQUIPMENT TO BE CONNECTED TO INFORMATION AND COMMUNICATION NETWORKS |
| I.S. EN 60950-22:2017 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 22: EQUIPMENT TO BE INSTALLED OUTDOORS |
| BS EN 50131-1 : 2006 | ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 1: SYSTEM REQUIREMENTS |
| EN 50131-1:2006/A2:2017 | ALARM SYSTEMS - INTRUSION AND HOLD-UP SYSTEMS - PART 1: SYSTEM REQUIREMENTS |
| UNE-EN 50131-1:2008 | Alarm systems - Intrusion and hold-up systems -- Part 1: System requirements |
| I.S. EN IEC 60728-3:2018 | CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES - PART 3: ACTIVE WIDEBAND EQUIPMENT FOR CABLE NETWORKS (TA 5) |
| I.S. EN IEC 62684:2018 | INTEROPERABILITY SPECIFICATIONS OF COMMON EXTERNAL POWER SUPPLY (EPS) FOR USE WITH DATA-ENABLED MOBILE TELEPHONES |
| I.S. EN 50332-2:2013 | SOUND SYSTEM EQUIPMENT: HEADPHONES AND EARPHONES ASSOCIATED WITH PERSONAL MUSIC PLAYERS - MAXIMUM SOUND PRESSURE LEVEL MEASUREMENT METHODOLOGY - PART 2: MATCHING OF SETS WITH HEADPHONES IF EITHER OR BOTH ARE OFFERED SEPARATELY, OR ARE OFFERED AS ONE PACKAGE EQUIPMENT BUT WITH STANDARDISED CONNECTORS BETWEEN THE TWO ALLOWING TO COMBINE COMPONENTS OF DIFFERENT MANUFACTURERS |
| EN IEC 60728-3:2018 | Cable networks for television signals, sound signals and interactive services - Part 3: Active wideband equipment for cable networks (TA 5) |
| CEI EN 63002 : 1ED 2017 | IDENTIFICATION AND COMMUNICATION INTEROPERABILITY METHOD FOR EXTERNAL POWER SUPPLIES USED WITH PORTABLE COMPUTING DEVICES |
| EN IEC 62684:2018 | Interoperability specifications of common external power supply (EPS) for use with data-enabled mobile telephones |
| S.R. CLC/TR 50656:2016 | SPD APPLICATION IN CONJUNCTION WITH CLASS 2 EQUIPMENT |
| EN 60940:2015 | Guidance information on the application of capacitors, resistors, inductors and complete filter units for electromagnetic interference suppression |
| IEC 60695-11-20:2015 | Fire hazard testing - Part 11-20: Test flames - 500 W flame test method |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| EN 60999-2:2003 | Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm² up to 300 mm² (included) |
| IEC 60320-1:2015 | Appliance couplers for household and similar general purposes - Part 1: General requirements |
| ISO 4892-1:2016 | Plastics — Methods of exposure to laboratory light sources — Part 1: General guidance |
| IEC 60906-3:1994 | IEC System of plugs and socket-outlets for household and similar purposes - Part 3: SELV plugs and socket-outlets, 16 A 6V, 12 V, 24 V, 48 V, a.c. and d.c. |
| IEC 60728-11:2016 | Cable networks for television signals, sound signals and interactive services - Part 11: Safety |
| IEC 61643-321:2001 | Components for low-voltage surge protective devices - Part 321: Specifications for avalanche breakdown diode (ABD) |
| EN 60998-1:2004 | Connecting devices for low-voltage circuits for household and similar purposes - Part 1: General requirements |
| IEC 61558-2-1:2007 | Safety of power transformers, power supplies, reactors and similar products - Part 2-1: Particular requirements and tests for separating transformers and power supplies incorporating separating transformers for general applications |
| IEC 60825-2:2004+AMD1:2006+AMD2:2010 CSV | Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS) |
| IEC 60245-1:2003+AMD1:2007 CSV | Rubber insulated cables - Rated voltages up to and including 450/750 V - Part 1: General requirements |
| ISO 7010:2011 | Graphical symbols Safety colours and safety signs Registered safety signs |
| IEC 60998-1:2002 | Connecting devices for low-voltage circuits for household and similar purposes - Part 1: General requirements |
| IEC 60738-1:2006+AMD1:2009 CSV | Thermistors - Directly heated positive temperature coefficient -Part 1: Generic specification |
| IEC TS 60479-1:2005+AMD1:2016 CSV | Effects of current on human beings and livestock - Part 1: Generalaspects |
| IEC 62281:2016 | Safety of primary and secondary lithium cells and batteries during transport |
| IEC 60107-1:1997 | Methods of measurement on receivers for television broadcast transmissions - Part 1: General considerations - Measurements at radio and video frequencies |
| EN ISO 8256:2004 | Plastics - Determination of tensile-impact strength (ISO 8256:2004) |
| IEC 60664-4:2005 | Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress |
| IEC 61984:2008 | Connectors - Safety requirements and tests |
| EN 61558-2-16:2009/A1:2013 | SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1 100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS (IEC 61558-2-16:2009/A1:2013) |
| EN 61558-2-4:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-4: Particular requirements and tests for isolating transformers and power supply units incorporating isolating transformers |
| IEC 60384-14:2013+AMD1:2016 CSV | Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains |
| ISO 871:2006 | Plastics Determination of ignition temperature using a hot-air furnace |
| IEC 60896-11:2002 | Stationary lead-acid batteries - Part 11: Vented types - General requirements and methods of tests |
| EN 60825-1:2014/AC:2017-06 | SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014) |
| EN 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements |
| EN 61427:2005 | Secondary cells and batteries for photovoltaic energy systems (PVES) - General requirements and methods of test |
| EN 60825-12:2004 | Safety of laser products - Part 12: Safety of free space optical communication systems used for transmission of information |
| IEC 61427:2005 | Secondary cells and batteries for photovoltaic energy systems (PVES) - General requirements and methods of test |
| EN 60065:2014/AC:2017-01 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016) |
| EN 61643-331:2003 | Components for low-voltage surge protective devices - Part 331: Specification for metal oxide varistors (MOV) |
| EN ISO 4892-1:2016 | Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO 4892-1:2016) |
| EN 60085:2008 | Electrical insulation - Thermal evaluation and designation |
| ISO 3864-2:2016 | Graphical symbols — Safety colours and safety signs — Part 2: Design principles for product safety labels |
| EN 50491-3:2009 | General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) - Part 3: Electrical safety requirements |
| EN 60695-10-2:2014 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| IEC 61558-2-4:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-4: Particular requirements and tests for isolating transformers and power supply units incorporating isolating transformers |
| IEC 61293:1994 | Marking of electrical equipment with ratings related to electrical supply - Safety requirements |
| IEC TS 61201:2007 | Use of conventional touch voltage limits - Application guide |
| EN 61434:1996 | Secondary cells and batteries containing alkaline or other non-acid electrolytes - Guide to the designation of current in alkaline secondary cell and battery standards |
| EN 61558-1:2005/A1:2009 | SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS |
| EN 60332-2-2:2004 | Tests on electric and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable - Procedure for diffusion flame |
| IEC TR 60083:2015 | Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC |
| ISO 9773:1998 | Plastics — Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame ignition source |
| IEC 60332-1-3:2004+AMD1:2015 CSV | Tests on electric and optical fibre cables under fire conditions - Part 1-3: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for determination of flamingdroplets/particles |
| IEC TR 62471-2:2009 | Photobiological safety of lamps and lamp systems - Part 2: Guidance on manufacturing requirements relating to non-laser optical radiation safety |
| IEC 60169-3:1965 | Radio-frequency connectors - Part 3: Two-pin connector for twin balanced aerial feeders |
| EN 50360:2017 | Product standard to demonstrate the compliance of wireless communication devices, with the basic restrictions and exposure limit values related to human exposure to electromagnetic fields in the frequency range from 300 MHz to 6 GHz: devices used next to the ear |
| EN 60738-1:2006/A1:2009 | THERMISTORS - DIRECTLY HEATED POSITIVE TEMPERATURE COEFFICIENT - PART 1: GENERIC SPECIFICATION |
| IEC 60999-2:2003 | Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included) |
| IEC 60896-21:2004 | Stationary lead-acid batteries - Part 21: Valve regulated types - Methods of test |
| IEC 60269-2:2013+AMD1:2016 CSV | Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Examples of standardized systems of fuses A to K |
| EN 60950-1:2006/A2:2013 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED) |
| IEC 62151:2000 | Safety of equipment electrically connected to a telecommunication network |
| IEC 61558-2-16:2009+AMD1:2013 CSV | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units |
| IEC 60130-9:2011 | Connectors for frequencies below 3 MHz - Part 9: Circular connectors for radio and associated sound equipment |
| IEC 60332-2-2:2004 | Tests on electric and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable - Procedure for diffusion flame |
| IEC 60825-1:2014 | Safety of laser products - Part 1: Equipment classification and requirements |
| CFR 21(PTS800-1299) : 0 | FOOD AND DRUGS - FOOD AND DRUG ADMINISTRATION, CHAPTER 1 DEPARTMENT OF HEALTH AND HUMAN SERVICES - PARTS 800-1299 |
| EN 50566:2017 | Product standard to demonstrate the compliance of wireless communication devices with the basic restrictions and exposure limit values related to human exposure to electromagnetic fields in the frequency range from 30 MHz to 6 GHz: hand-held and body mounted devices in close proximity to the human body |
| EN 60027-1:2006/A2:2007 | LETTER SYMBOLS TO BE USED IN ELECTRICAL TECHNOLOGY - PART 1: GENERAL |
| EN 60691:2016 | Thermal-links - Requirements and application guide |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| IEC 60825-12:2004 | Safety of laser products - Part 12: Safety of free space optical communication systems used for transmission of information |
| EN 61056-1:2012 | General purpose lead-acid batteries (valve-regulated types) - Part 1: General requirements, functional characteristics - Methods of test |
| IEC 60227-2:1997+AMD1:2003 CSV | Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 2: Test methods |
| IEC 61810-1:2015 | Electromechanical elementary relays - Part 1: General and safety requirements |
| IEC 60950-22:2016 | Information technology equipment - Safety - Part 22: Equipment to be installed outdoors |
| IEC 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| IEC 60950-23:2005 | Information technology equipment - Safety - Part 23: Large data storage equipment |
| EN 60332-1-2:2004/A11:2016 | TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 1-2: TEST FOR VERTICAL FLAME PROPAGATION FOR A SINGLE INSULATED WIRE OR CABLE - PROCEDURE FOR 1 KW PRE-MIXED FLAME (IEC 60332-1-2:2004/A1:2015) |
| IEC 61643-21:2000+AMD1:2008+AMD2:2012 CSV | Low voltage surge protective devices - Part 21: Surge protective devices connected to telecommunications and signalling networks - Performance requirements and testing methods |
| IEC 60695-10-3:2016 | Fire hazard testing - Part 10-3: Abnormal heat - Mould stress relief distortion test |
| EN 60947-1:2007/A2:2014 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014) |
| EN 61643-321:2002 | Components for low-voltage surge protective devices - Part 321: Specifications for Avalanche Breakdown Diode (ABD) |
| IEC 60027-1:1992 | Letters symbols to be used in electrical technology - Part 1: General |
| IEC 60851-6:2012 | Winding wires - Test methods - Part 6: Thermal properties |
| IEC 60851-5:2008+AMD1:2011 CSV | Winding wires - Test methods - Part 5: Electrical properties |
| IEC 61643-311:2013 | Components for low-voltage surge protective devices - Part 311: Performance requirements and test circuits for gas discharge tubes (GDT) |
| EN 61056-2:2012 | General purpose lead-acid batteries (valve-regulated types) - Part 2: Dimensions, terminals and marking |
| IEC 61056-2:2012 | General purpose lead-acid batteries (valve-regulated types) - Part 2: Dimensions, terminals and marking |
| IEC 60227-1:2007 | Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V - Part 1: General requirements |
| IEC 60332-1-2:2004+AMD1:2015 CSV | Tests on electric and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame propagation for a single insulatedwire or cable - Procedure for 1 kW pre-mixed flame |
| EN 60112 : 2003 AMD 1 2009 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| EN 60747-5-5:2011/A1:2015 | SEMICONDUCTOR DEVICES - DISCRETE DEVICES - PART 5-5: OPTOELECTRONIC DEVICES - PHOTOCOUPLERS (IEC 60747-5-5:2007/A1:2013) |
| IEC 60999-1:1999 | Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included) |
| EN 60728-11:2017 | Cable networks for television signals, sound signals and interactive services - Part 11: Safety |
| IEC 60601-2-4:2010 | Medical electrical equipment - Part 2-4: Particular requirements for the basic safety and essential performance of cardiac defibrillators |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| IEC TR 62368-2:2015 | Audio/video, information and communication technology equipment - Part 2: Explanatory information related to IEC 62368-1 |
| IEC 60320-2-2:1998 | Appliance couplers for household and similar general purposes - Part 2-2: Interconnection couplers for household and similar equipment |
| ISO/IEC Guide 51:2014 | Safety aspects — Guidelines for their inclusion in standards |
| EN 61959:2004 | Secondary cells and batteries containing alkaline or other non-acid electrolytes - Mechanical tests for sealed portable secondary cells and batteries |
| IEC 61558-1:2017 | Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests |
| EN 50332-1:2013 | Sound system equipment: Headphones and earphones associated with personal music players - Maximum sound pressure level measurement methodology - Part 1: General method for "one package equipment" |
| ISO/IEC Guide 37:2012 | Instructions for use of products by consumers |
| EN 71-1:2014 | Safety of toys - Part 1: Mechanical and physical properties |
| IEC 61643-1:2005 | Low-voltage surge protective devices - Part 1: Surge protective devices connected to low-voltage power distribution systems - Requirements and tests |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| EN 61558-2-1:2007 | Safety of power transformers, power supplies, reactors and similar products - Part 2-1: Particular requirements and tests for separating transformers and power supplies incorporating separating transformers for general applications |
| IEC 60906-2:2011 | IEC system of plugs and socket-outlets for household and similar purposes - Part 2: Plugs and socket-outlets 15 A 125 V a.c. and 20 A 125 V a.c. |
| EN 60851-6:2012 | Winding wires - Test methods - Part 6: Thermal properties |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| EN ISO 179 : 1996 | PLASTICS - DETERMINATION OF CHARPY IMPACT STRENGTH |
| ISO 9772:2012 | Cellular plastics Determination of horizontal burning characteristics of small specimens subjected to a small flame |
| IEC 61058-1:2016 | Switches for appliances - Part 1: General requirements |
| IEC 60896-22:2004 | Stationary lead-acid batteries - Part 22: Valve regulated types - Requirements |
| IEC 60364-4-44:2007+AMD1:2015 CSV | Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances |
| IEC 60691:2015 | Thermal-links - Requirements and application guide |
| IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV | Low-voltage switchgear and controlgear - Part 1: General rules |
| IEC 61056-1:2012 | General purpose lead-acid batteries (valve-regulated types) - Part 1: General requirements, functional characteristics - Methods of test |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| EN 60695-10-3:2016 | Fire hazard testing - Part 10-3: Abnormal heat - Mould stress relief distortion test |
| IEC 61051-2:1991 | Varistors for use in electronic equipment - Part 2: Sectional specification for surge suppression varistors |
| EN 60896-11:2003 | Stationary lead-acid batteries - Part 11: Vented types - General requirements and methods of tests |
| EN 61032:1998 | Protection of persons and equipment by enclosures - Probes for verification |
| EN 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 61643-11:2011 | Low-voltage surge protective devices - Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods |
| IEC TS 60695-11-21:2005 | Fire hazard testing - Part 11-21: Test flames - 500 W vertical flame test method for tubular polymeric materials |
| IEC 60906-1:2009 | IEC system of plugs and socket-outlets for household and similar purposes - Part 1: Plugs and socket-outlets 16 A 250 V a.c. |
| EN 50332-2:2013 | Sound system equipment: Headphones and earphones associated with personal music players - Maximum sound pressure level measurement methodology - Part 2: Matching of sets with headphones if either or both are offered separately, or are offered as one package equipment but with standardised connectors between the two allowing to combine components of different manufacturers or different design |
| IEC 60851-3:2009+AMD1:2013 CSV | Winding wires - Test methods - Part 3: Mechanical properties |
| IEC 60664-5:2007 | Insulation coordination for equipment within low-voltage systems - Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm |
| EN 60130-9:2011 | Connectors for frequencies below 3 MHz - Part 9: Circular connectors for radio and associated sound equipment |
| ISO 4892-4:2013 | Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps |
| EN 60317-43:1997/A1:2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 43: AROMATIC POLYIMIDE TAPE WRAPPED ROUND COPPER WIRE, CLASS 240 |
| IEC 62471:2006 | Photobiological safety of lamps and lamp systems |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| EN 60950-22:2017 | Information technology equipment - Safety - Part 22: Equipment to be installed outdoors |
| HD 60269-2:2013 | Low-voltage fuses - Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application) - Examples of standardized systems of fuses A to K |
| EN 60068-2-78:2013 | Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| EN 61965:2003 | Mechanical safety of cathode ray tubes |
| ISO 4892-2:2013 | Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| EN 60086-4:2015 | Primary batteries - Part 4: Safety of lithium batteries |
| EN 50395 : 2005 AMD 1 2011 | ELECTRICAL TEST METHODS FOR LOW VOLTAGE ENERGY CABLES |
| EN 61058-1:2002/A2:2008 | SWITCHES FOR APPLIANCES - PART 1: GENERAL REQUIREMENTS |
| IEC 61965:2003 | Mechanical safety of cathode ray tubes |
| IEC 61434:1996 | Secondary cells and batteries containing alkaline or other non-acid electrolytes - Guide to designation of current in alkaline secondary cell and battery standards |
| IEC 60664-3:2016 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| EN 60999-1:2000 | Connecting devices - Electrical copper conductors - Safety requirements for screw-type and screwless-type clamping units - Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm² up to 35 mm² (included) |
| EN 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| EN 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| IEC 61643-331:2003 | Components for low-voltage surge protective devices - Part 331: Specification for metal oxide varistors (MOV) |
| IEC 60747-5-5:2007+AMD1:2013 CSV | Semiconductor devices - Discrete devices - Part 5-5: Optoelectronic devices - Photocouplers |
| IEC 60086-5:2016 | Primary batteries - Part 5: Safety of batteries with aqueous electrolyte |
| EN 61984:2009 | Connectors - Safety requirements and tests |
| IEC 60695-10-2:2014 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| IEC 61508-1:2010 | Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508) |
| IEC 60086-4:2014 | Primary batteries - Part 4: Safety of lithium batteries |
| EN 61293:1994 | Marking of electrical equipment with ratings related to electrical supply - Safety requirements |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| EN 60896-22:2004 | Stationary lead-acid batteries - Part 22: Valve regulated types - Requirements |
| IEC 60317-43:1997+AMD1:2010 CSV | Specifications for particular types of winding wires - Part 43: Aromatic polyimide type wrapped round copper wire, class 240 |
| EN 60107-1:1997 | Methods of measurement on receivers for television broadcast transmissions - Part 1: General considerations - Measurements at radio and video frequencies |
| IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| EN 60825-2:2004/A2:2010 | SAFETY OF LASER PRODUCTS - PART 2: SAFETY OF OPTICAL FIBRE COMMUNICATION SYSTEMS (OFCS) |
| EN 60664-5:2007 | Insulation coordination for equipment within low-voltage systems - Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm |
| IEC 61204-7:2016 EXV | LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS |
| EN 60695-11-5:2017 | Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance |
| IEC 61032:1997 | Protection of persons and equipment by enclosures - Probes for verification |
| IEC 61959:2004 | Secondary cells and batteries containing alkaline or other non-acid electrolytes - Mechanical tests for sealed portable secondary cells and batteries |
| IEC 60695-11-5:2016 | Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance |
| IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV | Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements |
| AS/NZS 3112:2017 | Approval and test specification - Plugs and socket-outlets |
| EN 60320-2-2:1998 | Appliance couplers for household and similar general purposes - Part 2-2: Interconnection couplers for household and similar equipment |
| EN 62471:2008 | Photobiological safety of lamps and lamp systems |
| EN 60950-23:2006/corrigendum:2008 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 23: LARGE DATA STORAGE EQUIPMENT |
| ISO 178:2010 | Plastics Determination of flexural properties |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| EN ISO 306:2013 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013) |
| EN ISO 7010 : 2012 AMD 7 2017 | GRAPHICAL SYMBOLS - SAFETY COLOURS AND SAFETY SIGNS - REGISTERED SAFETY SIGNS (ISO 7010:2011/AMD 7:2016) |
| EN 60896-21:2004 | Stationary lead-acid batteries - Part 21: Valve regulated types - Methods of test |
| EN ISO 4892-2:2013 | Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc lamps (ISO 4892-2:2013) |
| EN 60664-3:2017 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| EN 50396 : 2005 AMD 1 2011 | NON ELECTRICAL TEST METHODS FOR LOW VOLTAGE ENERGY CABLES |
| IEC 61051-1:2007 | Varistors for use in electronic equipment - Part 1: Generic specification |
| EN 60320-1:2015/AC:2016 | APPLIANCE COUPLERS FOR HOUSEHOLD AND SIMILAR GENERAL PURPOSES - PART 1: GENERAL REQUIREMENTS (IEC 60320-1:2015/COR1:2016) |
| IEC 62485-2:2010 | Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries |
| EN 61643-311:2013 | Components for low-voltage surge protective devices - Part 311: Performance requirements and test circuits for gas discharge tubes (GDT) |
| EN 60851-5:2008/A1:2011 | WINDING WIRES - TEST METHODS - PART 5: ELECTRICAL PROPERTIES (IEC 60851-5:2008) |
| EN 60332-1-3:2004/A1:2015 | TESTS ON ELECTRIC AND OPTICAL FIBRE CABLES UNDER FIRE CONDITIONS - PART 1-3: TEST FOR VERTICAL FLAME PROPAGATION FOR A SINGLE INSULATED WIRE OR CABLE - PROCEDURE FOR DETERMINATION OF FLAMING DROPLETS/PARTICLES (IEC 60332-1-3:2004/A1:2015) |
| IEC 60990:2016 | Methods of measurement of touch current and protective conductor current |
| EN 60601-2-4:2011 | Medical electrical equipment - Part 2-4: Particular requirements for the basic safety and essential performance of cardiac defibrillators |
| EN 60730-1:2016 | Automatic electrical controls - Part 1: General requirements |
| EN 60309-1:1999/A1:2007/AC:2014 | PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 1: GENERAL REQUIREMENTS (IEC 60309-1:1999/A2:2012) |
| IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
| EN 60990:2016 | Methods of measurement of touch current and protective conductor current |
| EN 62133:2013 | Secondary cells and batteries containing alkaline or other non-acid electrolytes - Safety requirements for portable sealed secondary cells, and for batteries made from them, for use in portable applications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.