EN 62040-4:2013
Current
The latest, up-to-date edition.
Uninterruptible power systems (UPS) - Part 4: Environmental aspects - Requirements and reporting
27-09-2013
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Process of declaring the environmental aspects
of a UPS
5 Requirements
Annex A (normative) - Declaration of essential
requirements
Annex B (informative) - Declaration for additional
requirements
Annex C (informative) - Environmental aspects under
consideration
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
IEC 62040-4:2013 specifies the process and requirements to declare the environmental aspects concerning uninterruptible power systems (UPS), with the goal of promoting reduction of any adverse environmental impact during a complete UPS life cycle. This product standard is harmonized with the applicable generic and horizontal environmental standards and contains additional details relevant to UPS. This standard applies to movable, stationary and fixed UPS that deliver single or three-phase fixed frequency a.c. output voltage not exceeding 1 000 V a.c. and that present, generally through a d.c. link, an energy storage system and specified in IEC 62040 product standards for UPS.
| Committee |
CLC/TC 22X
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Current
|
| Standards | Relationship |
| IEC 62040-4:2013 | Identical |
| NBN EN 62040-4 : 2013 | Identical |
| NF EN 62040-4 : 2014 | Identical |
| I.S. EN 62040-4:2013 | Identical |
| NEN EN IEC 62040-4 : 2013 | Identical |
| BS EN 62040-4:2013 | Identical |
| VDE 0558-540 : 2014 | Identical |
| SN EN 62040-4:2013 | Identical |
| UNE-EN 62040-4:2013 | Identical |
| PN EN 62040-4 : 2014 | Identical |
| DIN EN 62040-4 : 2014 | Identical |
| CEI EN 62040-4 : 2014 | Identical |
| PNE-FprEN 62040-4 | Identical |
| IEC GUIDE 109:2012 | Environmental aspects - Inclusion in electrotechnical product standards |
| ISO 15270:2008 | Plastics — Guidelines for the recovery and recycling of plastics waste |
| IEC PAS 62545:2008 | Environmental information on Electrical and Electronic Equipment (EIEEE) |
| IEC 62310-2:2006 | Static transfer systems (STS) - Part 2: Electromagnetic compatibility (EMC) requirements |
| IEC TR 62635:2012 | Guidelines for end-of-life information provided by manufacturers and recyclers and for recyclability rate calculation of electrical and electronic equipment |
| ISO 14024:1999 | Environmental labels and declarations Type I environmental labelling Principles and procedures |
| ISO 14064-1:2006 | Greenhouse gases Part 1: Specification with guidance at the organization level for quantification and reporting of greenhouse gas emissions and removals |
| IEC 62310-3:2008 | Static transfer systems (STS) - Part 3: Method for specifying performance and test requirements |
| IEC 62430:2009 | Environmentally conscious design for electrical and electronic products |
| IEC 62310-1:2005 | Static transfer systems (STS) - Part 1: General and safety requirements |
| IEC 62535:2008 | Insulating liquids - Test method for detection of potentially corrosive sulphur in used and unused insulating oil |
| IEC 62040-1:2017 EXV | UNINTERRUPTIBLE POWER SYSTEMS (UPS) - PART 1: SAFETY REQUIREMENTS |
| EN 62040-3:2011 | Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements |
| IEC 62040-2:2016 | Uninterruptible power systems (UPS) - Part 2: Electromagnetic compatibility (EMC) requirements |
| ISO/TR 14062:2002 | Environmental management Integrating environmental aspects into product design and development |
| IEC 62040-3:2011 | Uninterruptible power systems (UPS) - Part 3: Method of specifying the performance and test requirements |
| ISO 14001:2015 | Environmental management systems — Requirements with guidance for use |
| ISO 14020:2000 | Environmental labels and declarations — General principles |
| EN 62474:2012 | Material declaration for products of and for the electrotechnical industry |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| ISO 14025:2006 | Environmental labels and declarations — Type III environmental declarations — Principles and procedures |
| ISO 14040:2006 | Environmental management Life cycle assessment Principles and framework |
| IEC 62474:2012 | Material declaration for products of and for the electrotechnical industry |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.