EN 61811-11:2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Electromechanical elementary relays of assessed quality - Part 11: Blank detail specification - Relays for industrial application
01-03-2015
18-02-2003
1 General
1.1 Scope
1.2 Normative references
1.3 Front page of detail specification
2 Characteristic values of the relay
2.1 General data
2.2 Construction of IECQ type designation (ordering
information)
2.3 Coil data
2.4 Contact data
2.5 Terminals
2.6 Mounting
2.7 Environmental data
3 Qualification approval procedures
4 Quality conformance inspection
4.1 Formation of inspection lots
4.2 Intervals between group C tests
5 Marking of relay and package
5.1 Marking of the relay
5.2 Marking of package
5.3 Documentation
6 Annexes
7 Tests
7.1 Standard conditions for testing
7.2 Mounting of test items during test
7.3 General conditions for testing
8 Ordering information
Annex ZA (normative) Normative references to international
publications with their corresponding European publications
Is based on the generic specification EN 61811-1 and the sectional specification EN 61811-10 and selects from EN 61810-7 the appropriate test and measurement procedures to be used in detail specifications derived from this specification
| Committee |
CLC/SR 94
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NF EN 61811-11 : 2003 | Identical |
| IEC 61811-11:2002 | Identical |
| NBN EN 61811-11 : 2003 | Identical |
| NEN EN IEC 61811-11 : 2003 | Identical |
| I.S. EN 61811-11:2003 | Identical |
| PN EN 61811-11 : 2005 | Identical |
| SN EN 61811-11 : 2003 | Identical |
| BS EN 61811-11:2003 | Identical |
| DIN EN 61811-11:2003-08 | Identical |
| PNE-prEN 61811-11 | Identical |
| UNE-EN 61811-11:2003 | Identical |
| CEI EN 61811-11 : 2004 | Identical |
| EN 60255-23:1996 | Electrical relays - Part 23: Contact performance |
| IEC 60068-1:2013 | Environmental testing - Part 1: General and guidance |
| IEC 61810-5:1998 | Electromechanical non-specified time all-or-nothing relays - Part 5: Insulation coordination |
| IEC 61811-10:2002 | Electromechanical elementary relays of assessed quality - Part 10: Sectional specification - Relays for industrial application |
| IEC 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| EN 60068-1:2014 | Environmental testing - Part 1: General and guidance |
| IEC 60695-2-11:2014 | Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) |
| IEC 61810-1:2015 | Electromechanical elementary relays - Part 1: General and safety requirements |
| IEC 61810-7:2006 | Electromechanical elementary relays - Part 7: Test and measurement procedures |
| EN 61810-5 : 1998 | ELECTROMECHANICAL NON-SPECIFIED TIME ALL-OR-NOTHING RELAYS - INSULATION COORDINATION |
| IEC 60695-2-12:2010+AMD1:2014 CSV | Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods- Glow-wire flammability index (GWFI) test method for materials |
| IEC 60068-2-47:2005 | Environmental testing - Part 2-47: Test - Mounting of specimens for vibration, impact and similar dynamic tests |
| IEC 60068-2-10:2005 | Environmental testing - Part 2-10: Tests - Test J and guidance: Mould growth |
| EN 60068-2-21:2006 | Environmental testing - Part 2-21: Tests - Test U: Robustness of terminations and integral mounting devices |
| IEC 60062:2016 | Marking codes for resistors and capacitors |
| EN 60062:2016/AC:2016-12 | MARKING CODES FOR RESISTORS AND CAPACITORS (IEC 60062:2016/COR1:2016) |
| HD 323.2.10 : 200S3 | BASIC ENVIRONMENTAL TESTING PROCEDURES - TESTS - TEST J AND GUIDANCE: MOULD GROWTH |
| IEC 61811-1:2015 | Electromechanical telecom elementary relays of assessed quality - Part 1: Generic specification and blank detail specification |
| IEC 60255-23:1994 | Electrical relays - Part 23: Contact performance |
| EN 61811-10:2003 | Electromechanical elementary relays of assessed quality - Part 10: Sectional specification - Relays for industrial application |
| EN 60695-2-12:2010/A1:2014 | FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS (IEC 60695-2-12:2010/A1:2014) |
| EN 61811-1:2015 | Electromechanical telecom elementary relays of assessed quality - Part 1: Generic specification and blank detail specification |
| EN 60695-2-11:2014 | Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) (IEC 60695-2-11:2014) |
| EN 60068-2-47:2005 | Environmental testing - Part 2-47: Tests - Mounting of specimens for vibration, impact and similar dynamic tests |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.