EN 40-6:2002
Current
The latest, up-to-date edition.
Lighting columns - Part 6: Requirements for aluminium lighting columns
17-04-2002
Foreword
1 Scope
2 Normative references
3 Terms and Definitions
4 Materials
5 Dimensions
6 Design and design verification
7 Welding
8 Joints
9 Protection against mechanical impact
10 Internal finish and sharp edges
11 Corrosion protection
12 Marking
13 Conformity control
14 Acceptance criteria
15 Re-testing
16 Performance under vehicle impact - Passive safety
Annex A (informative) Corrosion protection for aluminium
lighting columns
Annex B (informative) Recommendations for storage and
installation
Annex C (normative) Initial type tests
Annex ZA (informative) Clauses of this European standard
addressing the provisions of the EU Construction
Products Directive
This European Standard specifies requirements for aluminium lighting columns. It includes materials and conformity control. It applies to post top columns not exceeding 20 m height for post top lanterns and to columns with brackets not exceeding 18 m height for side entry lanterns.This European Standard specifies performance related to the essential requirements of resistance to horizontal (wind) loads and performance under impact in support of the Essential Requirement No 4 Safety in use measured according to the corresponding test methods included in this European Standard or available in separate European Standards.It provides for the evaluation of conformity of the products to this European Standard.
| Committee |
CEN/TC 50
|
| DevelopmentNote |
Supersedes EN 40-3. Supersedes EN 40-4:1982 (01/2006)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| UNE-EN 40-6:2003 | Identical |
| NBN EN 40-6 : 2002 | Identical |
| NF EN 40-6 : 2002 | Identical |
| NEN EN 40-6 : 2002 | Identical |
| NS EN 40-6 : 2ED 2002 | Identical |
| I.S. EN 40-6:2002 | Identical |
| PN EN 40-6 : 2004 | Identical |
| SN EN 40-6 : 2002 | Identical |
| UNE 72406:1984 | Identical |
| UNI EN 40-6 : 2004 | Identical |
| BS EN 40-6:2002 | Identical |
| BS 5649-6:1982 | Identical |
| DIN EN 40-6:2002-09 | Identical |
| NFP 97 405 : 1980 | Identical |
| 17/30364350 DC : 0 | BS EN 12767 - PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS AND TEST METHODS |
| EN 12767:2007 | Passive safety of support structures for road equipment - Requirements, classification and test methods |
| 12/30260931 DC : 0 | BS EN 40-3-2 - LIGHTING COLUMNS - PART 3-2: DESIGN AND VERIFICATION - VERIFICATION BY TESTING |
| I.S. EN 12767:2007 | PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS, CLASSIFICATION AND TEST METHODS |
| DIN EN 12767:2008-01 | PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS, CLASSIFICATION AND TEST METHODS |
| UNE-EN 40-3-2:2013 | Lighting columns - Part 3-2: Design and verification - Verification by testing |
| I.S. EN 40-3-2:2013 | LIGHTING COLUMNS - PART 3-2: DESIGN AND VERIFICATION - VERIFICATION BY TESTING |
| PREN 12767 : DRAFT 2017 | PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS AND TEST METHODS |
| BS EN 40-3-2:2013 | Lighting columns Design and verification. Verification by testing |
| UNI EN 40-3-2 : 2013 | LIGHTING COLUMNS - PART 3-2: DESIGN AND VERIFICATION - VERIFICATION BY TESTING |
| PREN 40-3-2 : DRAFT 2012 | LIGHTING COLUMNS - DESIGN AND VERIFICATION - PART 3-2: VERIFICATION BY TESTING |
| 13/30286641 DC : 0 | BS EN 12767 - PASSIVE SAFETY OF SUPPORT STRUCTURES FOR ROAD EQUIPMENT - REQUIREMENTS AND TEST METHODS |
| DIN EN 40-3-2:2013-06 | LIGHTING COLUMNS - PART 3-2: DESIGN AND VERIFICATION - VERIFICATION BY TESTING |
| EN 40-3-2:2013 | Lighting columns - Part 3-2: Design and verification - Verification by testing |
| BS EN 12767:2007 | Passive safety of support structures for road equipment. Requirements, classification and test methods |
| EN 40-3-1:2013 | Lighting columns - Part 3-1: Design and verification - Specification for characteristic loads |
| EN 288-1:1992/A1:1997 | SPECIFICATION AND QUALIFICATION OF WELDING PROCEDURES FOR METALLIC MATERIALS - GENERAL RULES FOR FUSION WELDING |
| EN 40-3-2:2013 | Lighting columns - Part 3-2: Design and verification - Verification by testing |
| EN 485-3:2003 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 3: Tolerances on dimensions and form for hot-rolled products |
| EN 485-4:1993 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 4: Tolerances on shape and dimensions for cold-rolled products |
| 89/106/EEC : 1988 | COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS |
| EN 288-4:1992/A1:1997 | SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - WELDING PROCEDURES FOR THE ARC WELDING OF ALUMINIUM AND ITS ALLOYS |
| EN 1011-1:2009 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| EN 755-8:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form |
| EN 50102:1995/corrigendum Jul. 2002 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES FOR ELECTRICAL EQUIPMENT AGAINST EXTERNAL MECHANICAL IMPACTS (IK CODE) |
| EN 10025:1990/A1:1993 | HOT ROLLED PRODUCTS OF NON-ALLOY STRUCTURAL STEELS - TECHNICAL DELIVERY CONDITIONS |
| EN 755-7:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 7: Seamless tubes, tolerances on dimensions and form |
| EN 288-2:1992/A1:1997 | SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - PART 2: WELDING PROCEDURE SPECIFICATION FOR ARC WELDING |
| EN 40-1:1991 | Lighting columns - Part 1: Definitions and terms |
| EN 1706:2010 | Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties |
| EN 12767:2007 | Passive safety of support structures for road equipment - Requirements, classification and test methods |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 288-8 : 1995 | SPECIFICATION AND APPROVAL OF WELDING PROCEDURES FOR METALLIC MATERIALS - PART 8: APPROVAL BY A PRE-PRODUCTION WELDING TEST |
| EN 571-1:1997 | Non destructive testing - Penetrant testing - Part 1: General principles |
| EN 970:1997 | Non-destructive examination of fusion welds - Visual examination |
| PREN 40-3-3 : DRAFT 2012 | LIGHTING COLUMNS - PART 3-3: DESIGN AND VERIFICATION - VERIFICATION BY CALCULATION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.