EN 16905-5:2017

European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Part load conditions in cooling mode
5 Part load conditions in heating mode
6 Calculation methods for reference SPER[c]
7 Calculation methods for reference SPER[h]
Annex A (normative) - Determination of reference
        annual cooling/heating demands and
        determination of hours for active mode,
        thermostat off, standby, off mode and
        crankcase heater mode for reference
        SAEF[C] and SAEF[h] calculation
Annex B (informative) - Calculation example for
        reference SGUE[c], SAEF[c],
        SEHREgas[c], SEHREelec[c] and SPER[c]
Annex C (informative) - Calculation example for
        reference SGUE[h], SAEF[h], SEHREgas[h],
        SEHREelec[h] and SPER[h]
Annex D (informative) - Adaption of water temperature
        for fixed capacity
Annex E (informative) - Compensation method for air
        to water and water to water units
Annex ZA (informative) - Relationship between this
         European Standard and the ecodesign
         requirements of Commission Regulation
         (EU) No 813/2013 aimed to be covered
Annex ZB (informative) - Relationship between this
         European Standard and the energy
         labelling requirements of Commission
         Delegated Regulation (EU) No 811/2013
         aimed to be covered
Bibliography

1.1Scope of FprEN 16905 seriesThis European Standard specifies the requirements, test methods and test conditions for the rating and performance calculation of air conditioners and heat pumps using either air, water or brine as heat transfer media, with gas-fired endothermic engine driven compressors when used for space heating, cooling and refrigeration, hereafter referred to as “GEHP appliance”.This European Standard only applies to appliances with a maximum heat input (based on net calorific value) not exceeding 70 kW at standard rating conditions.This European Standard only applies to appliances under categories I2H, I2E, I2Er, I2R, I2E(S)B, I2L, I2LL, I2ELL, I2E(R)B, I2ESi, I2E(R), I3P, I3B, I3B/P, II2H3+, II2Er3+, II2H3B/P, II2L3B/P, II2E3B/P, II2ELL3B/P, II2L3P, II2H3P, II2E3P and II2Er3P according to EN 437.This European Standard only applies to appliances having:a)gas fired endothermic engines under the control of fully automatic control systems;b)closed system refrigerant circuits in which the refrigerant does not come into direct contact with the fluid to be cooled or heated;c)where the temperature of the heat transfer fluid of the heating system (heating water circuit) does not exceed 105 °C during normal operation;d)where the maximum operating pressure in the:1)heating water circuit (if installed) does not exceed 6 bar,2)domestic hot water circuit (if installed) does not exceed 10 bar.This European Standard applies to appliances only when used for space heating or space cooling or for refrigeration, with or without heat recovery.The appliances having their condenser cooled by air and by the evaporation of external additional water are not covered by this European Standard.Packaged units, single split and multisplit systems are covered by this European Standard. Single duct and double duct units are covered by this European Standard.The above appliances can have one or more primary or secondary functions.This European Standard is applicable to appliances that are intended to be type tested. Requirements for appliances that are not type tested would need to be subject to further consideration.In the case of packaged units (consisting of several parts), this European Standard applies only to those designed and supplied as a complete package.NOTEAll the symbols given in this text are used regardless of the language used.1.2Scope of FprEN 16905 5This part of the FprEN 16905 series specifies the calculation of seasonal performance factor for gas-fired endothermic engine driven heat pumps for heating and/or cooling mode including the engine heat recovery.