• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

DIN ISO 7919-2:2010-06

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON ROTATING SHAFTS - PART 2: LAND-BASED STEAM TURBINES AND GENERATORS IN EXCESS OF 50 MW WITH NORMAL OPERATING SPEEDS OF 1500 R/MIN, 1800 R/MIN, 3000 R/MIN AND 3600 R/MIN

Available format(s)

Hardcopy , PDF

Superseded date

01-01-2018

Language(s)

English

Published date

01-01-2010

£77.97
Excluding VAT

Foreword
Introduction
1 Scope
2 Normative references
3 Measurement procedure
4 Evaluation criteria
Annex A (normative) Evaluation zones boundaries
Annex B (informative) Evaluation zone boundary values
        and bearing clearance
Bibliography

Specifies provisions for evaluating the severity of in-situ, broad-band shaft vibration measured radial (i.e. transverse) to the shaft axis at, or close to, the main bearings. These are in terms of: - vibration under normal steady-state operating conditions; - vibration during other (non-steady-state) conditions when transient changes are taking place, including run up or run down, initial loading and load changes; - changes in vibration which can occur during normal steady-state operation.

DocumentType
Standard
Pages
17
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded
SupersededBy

Standards Relationship
ISO 7919-2:2009 Identical

DIN ISO 10816-7:2009-08 MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 7: ROTODYNAMIC PUMPS FOR INDUSTRIAL APPLICATIONS, INCLUDING MEASUREMENTS ON ROTATING SHAFTS
DIN ISO 11342:1999-05 MECHANICAL VIBRATION - METHODS AND CRITERIA FOR THE MECHANICAL BALANCING OF FLEXIBLE ROTORS
DIN ISO 13373-3:2015-12 CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - VIBRATION CONDITION MONITORING - PART 3: GUIDELINES FOR VIBRATION DIAGNOSIS (ISO 13373-3:2015)
VDI 3840:2004-05 Vibration analysis for machine sets
VDI 3839 Blatt 5:2001-09 Instructions on measuring and interpreting the vibration of machines - Typical vibration patterns with electrical machines
VDI 3840:2004-05 VIBRATION ANALYSIS FOR MACHINE SETS
VDI 2038 Blatt 1:2012-06 Serviceability of structures under dynamic loads - Methods of analysis and evaluation in structural dynamics - Basics, methods, procedures and loads
VDI 3839 Blatt 1:2001-03 Instructions on measuring and interpreting the vibrations of machines - General principles
DIN ISO 17359:2011-09 CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - GENERAL GUIDELINES
DIN ISO 18436-2:2014-11 CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - REQUIREMENTS FOR QUALIFICATION AND ASSESSMENT OF PERSONNEL - PART 2: VIBRATION CONDITION MONITORING AND DIAGNOSTICS (ISO 18436-2:2014)
DIN ISO 20816-1:2015-12 (Draft) MECHANICAL VIBRATION - MEASUREMENT AND EVALUATION OF MACHINE VIBRATION - PART 1: GENERAL GUIDELINES (ISO 20816-1:2016)
DIN ISO 21940-12:2016-09 MECHANICAL VIBRATION - ROTOR BALANCING - PART 12: PROCEDURES AND TOLERANCES FOR ROTORS WITH FLEXIBLE BEHAVIOUR (ISO 21940-12:2016)
DIN ISO 11342 E : 1999 MECHANICAL VIBRATION - METHODS AND CRITERIA FOR THE MECHANICAL BALANCING OF FLEXIBLE ROTORS
DIN ISO 10817-1:1999-11 ROTATING SHAFT VIBRATION MEASURING SYSTEMS - PART 1: RELATIVE AND ABSOLUTE SENSING OF RADIAL VIBRATION

DIN ISO 7919-4:2010-06 MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON ROTATING SHAFTS - PART 4: GAS TURBINE SETS WITH FLUID-FILM BEARINGS (ISO 7919-4:2009 + AMD.1:2017)
ISO 10816-4:2009 Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 4: Gas turbine sets with fluid-film bearings
ISO 13373-1:2002 Condition monitoring and diagnostics of machines — Vibration condition monitoring — Part 1: General procedures
DIN ISO 10816-7:2009-08 MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON NON-ROTATING PARTS - PART 7: ROTODYNAMIC PUMPS FOR INDUSTRIAL APPLICATIONS, INCLUDING MEASUREMENTS ON ROTATING SHAFTS
DIN ISO 7919-5:2005-10 MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON ROTATING SHAFTS - PART 5: MACHINE SETS IN HYDRAULIC POWER GENERATING AND PUMPING PLANTS
DIN ISO 7919-1:1997-08 MECHANICAL VIBRATION OF NON-RECIPROCATING MACHINES - MEASUREMENTS ON ROTATING SHAFTS AND EVALUATION - PART 1: GENERAL GUIDELINES
ISO 10816-2:2009 Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600 r/min
ISO 10814:1996 Mechanical vibration Susceptibility and sensitivity of machines to unbalance
ISO 7919-1:1996 Mechanical vibration of non-reciprocating machines Measurements on rotating shafts and evaluation criteria Part 1: General guidelines
ISO 10816-5:2000 Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 5: Machine sets in hydraulic power generating and pumping plants
ISO 13373-2:2016 Condition monitoring and diagnostics of machines Vibration condition monitoring Part 2: Processing, analysis and presentation of vibration data
ISO 2041:2009 Mechanical vibration, shock and condition monitoring Vocabulary
DIN ISO 13373-2:2006-01 CONDITION MONITORING AND DIAGNOSTICS OF MACHINES - VIBRATION CONDITION MONITORING - PART 2: PROCESSING, ANALYSIS AND PRESENTATION OF VIBRATION DATA (ISO 13373-2:2016)
DIN ISO 10817-1:1999-11 ROTATING SHAFT VIBRATION MEASURING SYSTEMS - PART 1: RELATIVE AND ABSOLUTE SENSING OF RADIAL VIBRATION
ISO 10816-1:1995 Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 1: General guidelines
DIN ISO 7919-3:2009-08 MECHANICAL VIBRATION - EVALUATION OF MACHINE VIBRATION BY MEASUREMENTS ON ROTATING SHAFTS - PART 3: COUPLED INDUSTRIAL MACHINES (ISO 7919-3:2009 + AMD.1:2017)
ISO 10816-7:2009 Mechanical vibration Evaluation of machine vibration by measurements on non-rotating parts Part 7: Rotodynamic pumps for industrial applications, including measurements on rotating shafts
ISO 10817-1:1998 Rotating shaft vibration measuring systems Part 1: Relative and absolute sensing of radial vibration
ISO 5348:1998 Mechanical vibration and shock Mechanical mounting of accelerometers

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.