DIN EN ISO 8637:2014-03
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
CARDIOVASCULAR IMPLANTS AND EXTRACORPOREAL SYSTEMS - HAEMODIALYSERS, HAEMODIAFILTERS, HAEMOFILTERS AND HAEMOCONCENTRATORS (ISO 8637:2010, INCLUDING AMENDMENT 1:2013-04-01)
Hardcopy , PDF
07-03-2021
German, English
01-03-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Test methods
6 Labelling
Bibliography
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 93/42/EEC on medical devices
This standard is included in DIN Handbook 227/2.
| Committee |
TC 150
|
| DevelopmentNote |
Supersedes DIN EN 1283. (03/2014)
|
| DocumentType |
Standard
|
| Pages |
30
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| ISO 8637:2010 | Identical |
| EN ISO 8637:2014 | Identical |
| PREN ISO 8637 : DRAFT 2013 | Identical |
| DIN EN ISO 7199:2015-06 (Draft) | CARDIOVASCULAR IMPLANTS AND ARTIFICIAL ORGANS - BLOOD-GAS EXCHANGERS (OXYGENATORS) (ISO 7199:2016) |
| DIN HDBK 227/2 : 5ED 2016 | MEDIZINISCHE EINMALPRODUKTE - BAND 2: HAEMODIALYSE, DRAINAGEN UND KATHETER, HANDSCHUHE, KONDOME SOWIE INKONTINENZ- UND OSTOMIEHILFEN |
| ISO 11137-1:2006 | Sterilization of health care products Radiation Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices |
| ISO 10993-4:2017 | Biological evaluation of medical devices — Part 4: Selection of tests for interactions with blood |
| ISO 15223-2:2010 | Medical devices — Symbols to be used with medical device labels, labelling, and information to be supplied — Part 2: Symbol development, selection and validation |
| DIN EN ISO 10993-7:2009-02 | Biological evaluation of medical devices - Part 7: Ethylene oxide sterilization residuals (ISO 10993-7:2008) |
| ISO/TS 17665-2:2009 | Sterilization of health care products — Moist heat — Part 2: Guidance on the application of ISO 17665-1 |
| ISO 8638:2010 | Cardiovascular implants and extracorporeal systems Extracorporeal blood circuit for haemodialysers, haemodiafilters and haemofilters |
| DIN EN ISO 10993-11:2015-12 (Draft) | BIOLOGICAL EVALUATION OF MEDICAL DEVICES - PART 11: TESTS FOR SYSTEMIC TOXICITY |
| ISO 14937:2009 | Sterilization of health care products General requirements for characterization of a sterilizing agent and the development, validation and routine control of a sterilization process for medical devices |
| ISO 11135-1:2007 | Sterilization of health care products Ethylene oxide Part 1: Requirements for development, validation and routine control of a sterilization process for medical devices |
| ISO 10993-11:2017 | Biological evaluation of medical devices — Part 11: Tests for systemic toxicity |
| ISO 11137-3:2017 | Sterilization of health care products — Radiation — Part 3: Guidance on dosimetric aspects of development, validation and routine control |
| DIN EN ISO 10993-4:2016-02 (Draft) | BIOLOGICAL EVALUATION OF MEDICAL DEVICES - PART 4: SELECTION OF TESTS FOR INTERACTIONS WITH BLOOD (ISO 10993-4:2017) |
| ISO 10993-7:2008 | Biological evaluation of medical devices Part 7: Ethylene oxide sterilization residuals |
| ISO 11137-2:2013 | Sterilization of health care products — Radiation — Part 2: Establishing the sterilization dose |
| ISO 10993-1:2009 | Biological evaluation of medical devices Part 1: Evaluation and testing within a risk management process |
| ISO/TS 11135-2:2008 | Sterilization of health care products Ethylene oxide Part 2: Guidance on the application of ISO 11135-1 |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| ISO 594-2:1998 | Conical fittings with 6 % (Luer) taper for syringes, needles and certain other medical equipment Part 2: Lock fittings |
| ISO 15223-1:2016 | Medical devices Symbols to be used with medical device labels, labelling and information to be supplied Part 1: General requirements |
| ISO 17665-1:2006 | Sterilization of health care products — Moist heat — Part 1: Requirements for the development, validation and routine control of a sterilization process for medical devices |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.