DIN EN ISO 14373:2015-06
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels (ISO 14373:2015)
Available format(s)
Hardcopy , PDF
Superseded date
01-04-2024
Superseded by
Language(s)
German, English
Published date
01-06-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Materials
6 Surface conditions
7 Edge conditions, form of component, and weld
spacing
8 Electrodes
9 Weld assessment
10 Weld quality requirements
11 Multi-weld arrays
Annex A (informative) - Recommendations for spot
welding equipment
Annex B (informative) - Typical spot welding conditions
Annex C (informative) - Partial list of steel types applicable
to this International Standard
Bibliography
This standard is included in DIN Handbook 312.
| DocumentType |
Standard
|
| Pages |
23
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| BS EN ISO 14373:2015 | Identical |
| NEN EN ISO 14373 : 2015 | Identical |
| ISO 14373:2015 | Identical |
| EN ISO 14373:2015 | Identical |
| UNI EN ISO 14373 : 2008 | Identical |
| NBN EN ISO 14373 : 2015 | Identical |
| I.S. EN ISO 14373:2015 | Identical |
| SN EN ISO 14373:2015 | Identical |
| NF EN ISO 14373 : 2015 | Identical |
| NS EN ISO 14373 : 2015 | Identical |
| ONORM EN ISO 14373 : 2015 | Identical |
| DIN ISO 16338:2014-08 | WELDING FOR AEROSPACE APPLICATIONS - RESISTANCE SPOT AND SEAM WELDING (ISO 16338:2017) |
| DIN DVS HDBK 312/1 : 3ED 2010 | SCHWEISSTECHNIK 9 - WIDERSTANDSSCHWEISSEN - AUSBILDUNG, GRUNDLAGEN, VERFAHREN UND WERKSTOFFE |
| DIN EN ISO 18278-1:2015-08 | Resistance welding - Weldability - Part 1: General requirements for the evaluation of weldability for resistance spot, seam and projection welding of metallic materials (ISO 18278-1:2015) |
| DIN DVS HDBK 312 : 4ED 2017 | |
| DIN EN ISO 18278-2:2016-09 | RESISTANCE WELDING - WELDABILITY - PART 2: EVALUATION PROCEDURES FOR WELDABILITY IN SPOT WELDING (ISO 18278-2:2016) |
| DIN EN ISO 18595:2007-12 | Resistance welding - Spot welding of aluminium and aluminium alloys - Weldability, welding and testing (ISO 18595:2007); German version EN ISO 18595:2007 |
| DIN EN ISO 14270:2002-04 | RESISTANCE WELDING - DESTRUCTIVE TESTING OF WELDS - SPECIMEN DIMENSIONS AND PROCEDURE FOR MECHANIZED PEEL TESTING RESISTANCE SPOT, SEAM AND EMBOSSED PROJECTION WELDS (ISO 14270:2016) |
| ISO 5182:2016 | Resistance welding Materials for electrodes and ancillary equipment |
| DIN EN ISO 18278-1:2015-08 | Resistance welding - Weldability - Part 1: General requirements for the evaluation of weldability for resistance spot, seam and projection welding of metallic materials (ISO 18278-1:2015) |
| DIN EN ISO 15614-12:2014-10 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 12: Spot, seam and projection welding (ISO 15614-12:2014); German version EN ISO 15614-12:2014 |
| ISO 14270:2016 | Resistance welding Destructive testing of welds Specimen dimensions and procedure for mechanized peel testing resistance spot, seam and embossed projection welds |
| ISO 10447:2015 | Resistance welding — Testing of welds — Peel and chisel testing of resistance spot and projection welds |
| ISO 5830:1984 | Resistance spot welding Male electrode caps |
| ISO 3574:2012 | Cold-reduced carbon steel sheet of commercial and drawing qualities |
| DIN EN ISO 10447:2015-05 | Resistance welding - Testing of welds - Peel and chisel testing of resistance spot and projection welds (ISO 10447:2015) |
| DIN EN ISO 14329:2003-12 | Resistance welding - Destructive tests of welds - Failure types and geometric measurements for resistance spot, seam and projection welds (ISO 14329:2003); German version EN ISO 14329:2003 |
| DIN ISO 669:2001-06 | RESISTANCE WELDING - RESISTANCE WELDING EQUIPMENT - MECHANICAL AND ELECTRICAL REQUIREMENTS |
| DIN EN ISO 15609-5:2012-03 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 5: Resistance welding (ISO 15609-5:2011) |
| ISO 3573:2012 | Hot-rolled carbon steel sheet of commercial and drawing qualities |
| DIN ISO 5184:1984-04 | STRAIGHT RESISTANCE SPOT WELDING ELECTRODES |
| ISO 9364:2011 | Continuous hot-dip 55 % aluminium/zinc alloy-coated steel sheet of commercial, drawing and structural qualities |
| ISO 4998:2014 | Continuous hot-dip zinc-coated and zinc-iron alloy-coated carbon steel sheet of structural quality |
| ISO 5002:2013 | Hot-rolled and cold-reduced electrolytic zinc-coated carbon steel sheet of commercial and drawing qualities |
| DIN EN ISO 5821:2010-04 | Resistance welding - Spot welding electrode caps (ISO 5821:2009) |
| DIN EN ISO 18278-2:2016-09 | RESISTANCE WELDING - WELDABILITY - PART 2: EVALUATION PROCEDURES FOR WELDABILITY IN SPOT WELDING (ISO 18278-2:2016) |
| ISO 15614-12:2014 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 12: Spot, seam and projection welding |
| ISO 669:2016 | Resistance welding Resistance welding equipment Mechanical and electrical requirements |
| ISO 14329:2003 | Resistance welding Destructive tests of welds Failure types and geometric measurements for resistance spot, seam and projection welds |
| DIN EN ISO 5182:2015-03 (Draft) | RESISTANCE WELDING - MATERIALS FOR ELECTRODES AND ANCILLARY EQUIPMENT (ISO 5182:2016) |
| ISO 15609-5:2011 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 5: Resistance welding |
| DIN EN ISO 17677-1:2010-01 | RESISTANCE WELDING - VOCABULARY - PART 1: SPOT, PROJECTION AND SEAM WELDING |
| ISO 3575:2016 | Continuous hot-dip zinc-coated and zinc-iron alloy-coated carbon steel sheet of commercial and drawing qualities |
| ISO 4950-2:1995 | High yield strength flat steel products — Part 2: Products supplied in the normalized or controlled rolled condition |
| ISO 4950-1:1995 | High yield strength flat steel products — Part 1: General requirements |
| ISO 5000:2011 | Continuous hot-dip aluminium-silicon-coated cold-reduced carbon steel sheet of commercial and drawing qualities |
| ISO 5184:1979 | Straight resistance spot welding electrodes |
| ISO 17677-1:2009 | Resistance welding Vocabulary Part 1: Spot, projection and seam welding |
| ISO 18278-1:2015 | Resistance welding Weldability Part 1: General requirements for the evaluation of weldability for resistance spot, seam and projection welding of metallic materials |
| ISO 5821:2009 | Resistance welding — Spot welding electrode caps |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.