DIN EN 1090-2:2015-07 (Draft)
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES
Available format(s)
Hardcopy , PDF
Superseded date
21-09-2018
Superseded by
Language(s)
German
Published date
01-01-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Vorwort
Einleitung
1 Anwendungsbereich
2 Normative Verweisungen
2.1 Allgemeines
2.2 Konstruktionsmaterialien
2.3 Bearbeitung
2.4 Schweissen
2.5 Prüfungen
2.6 Montage
2.7 Korrosionsschutz
2.8 Toleranzen
2.9 Verschiedenes
3 Begriffe
4 Ausführungsunterlagen und Dokumentation
4.1 Ausführungsunterlagen
4.2 Herstellerdokumentation
5 Konstruktionsmaterialien
5.1 Allgemeines
5.2 Identifizierbarkeit, Prüfbescheinigungen
und Rückverfolgbarkeit
5.3 Vorprodukte für den Stahlbau
5.4 Stahlguss
5.5 Schweisszusätze
5.6 Mechanische Verbindungsmittel
5.7 Bolzen und Kopfbolzen
5.8 Vergussmaterial
5.9 Dehnfugen bei Brücken
5.10 Hochfeste Zugglieder, Stäbe und
Endverbindungen
5.11 Lager
6 Vorbereitung und Zusammenbau
6.1 Allgemeines
6.2 Identifizierbarkeit
6.3 Handhabung und Lagerung
6.4 Schneiden
6.5 Formgebung
6.6 Lochen
6.7 Ausschnitte
6.8 Oberflächen von Kontaktstössen
6.9 Zusammenbau
6.10 Überprüfung des Zusammenbaus
7 Schweissen
7.1 Allgemeines
7.2 Schweissplan
7.3 Schweissprozesse
7.4 Qualifizierung des Schweissverfahrens
und des Schweisspersonals
7.5 Vorbereitung und Ausführung von
Schweissarbeiten
7.6 Abnahmekriterien
7.7 Schweissen von nichtrostenden Stählen
8 Mechanische Verbindungsmittel
8.1 Allgemeines
8.2 Einsatz von Garnituren
8.3 Anziehen nicht planmässig vorgespannter
Schrauben
8.4 Vorbereitung von Kontaktflächen für
gleitfeste Verbindungen
8.5 Anziehen planmässig vorgespannter Schrauben
8.6 Passschrauben
8.7 Nieten
8.8 Befestigung dünnwandiger Bauteile
8.9 Einsatz besonderer Verbindungsmittel und
Befestigungsverfahren
8.10 Verschleiss und Fressen bei nichtrostenden
Stählen
9 Montage
9.1 Allgemeines
9.2 Baustellenbedingungen
9.3 Montageverfahren
9.4 Vermessung
9.5 Abstützungen, Verankerungen und Lager
9.6 Montage und Baustellenarbeiten
10 Oberflächenschutz
10.1 Allgemeines
10.2 Vorbereitung von Stahloberflächen
10.3 Wetterfeste Stähle
10.4 Kontaktkorrosion
10.5 Verzinken
10.6 Fugenabdichtung
10.7 Oberflächen in Kontakt mit Beton
10.8 Unzugängliche Oberflächen
10.9 Reparaturen nach dem Schneiden oder
Schweissen
10.10 Reinigung nach der Montage
11 Geometrische Toleranzen
11.1 Toleranzkategorien
11.2 Grundlegende Toleranzen
11.3 Ergänzende Toleranzen
12 Kontrolle, Prüfung und Korrekturmassnahmen
12.1 Allgemeines
12.3 Herstellung: Abmasse von hergestellten Bauteilen
12.4 Schweissen
12.5 Mechanische Verbindungsmittel
12.6 Oberflächenschutz und Korrosionsschutz
12.7 Montage
Anhang A (normativ) Zusatzangaben, Liste festzulegender
Auswahlmöglichkeiten und auf die
Ausführungsklassen bezogene Anforderungen
Anhang B (informativ) Leitfaden zur Bestimmung der
Ausführungsklassen
Anhang C (informativ) Checkliste für den Inhalt
eines Qualitätsmanagementplans
Anhang D (normativ) Geometrische Toleranzen
Anhang E (informativ) Geschweisste Hohlprofilverbindungen
Anhang F (normativ) Korrosionsschutz
Anhang G (normativ) Prüfung zur Bestimmung der
Haftreibungszahl
Anhang H (normativ) Prüfung zur Bestimmung des
Anziehdrehmoments bei planmässig
vorgespannten Schrauben unter Baustellenbedingungen
Anhang J (normativ) Einsatz von Scheiben mit direkten
Kraftanzeigern
Anhang K (informativ) Sechskant-Injektions-Schrauben
Anhang L (informativ) Flussdiagramm zur Erstellung und
Verwendung einer WPS
Anhang M (normativ) Sequentielles Verfahren zur
Kontrolle von Verbindungsmitteln
Literaturhinweise
This standard is included in DIN Handbook 93, DIN DVS Handbook 191 and DIN HANDBOOK 69/1.
| DevelopmentNote |
Supersedes DIN V ENV 1090-1, DIN V ENV 1090-2, DIN V ENV 1090-3, DIN V ENV 1090-4, DIN V ENV 1090-5 and DIN V ENV 1090-6. (12/2008) DRAFT 2016 issued in December 2016. (12/2016)
|
| DocumentType |
Draft
|
| Pages |
399
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN 1090-2:2008+A1:2011 | Identical |
| DIN 21530-2:2016-09 | MINE SUPPORT - PART 2: DIMENSIONS, DESIGNATION AND STATICAL VALUES |
| DIN HDBK 93 : 10ED 2016 | STAHLBAUARBEITEN VOB/STLB-BAU - VOB TEIL C: ATV DIN 18299, ATV DIN 18335 |
| I.S. EN 50341-2-4:2016 | OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 2-4: NATIONAL NORMATIVE ASPECTS (NNA) FOR GERMANY (BASED ON EN 50341-1:2012) |
| DIN 18335:2016-09 | GERMAN CONSTRUCTION CONTRACT PROCEDURES (VOB) - PART C: GENERAL TECHNICAL SPECIFICATIONS IN CONSTRUCTION CONTRACTS (ATV) - STEEL CONSTRUCTION WORKS |
| DIN 18516-1:2010-06 | Cladding for external walls, ventilated at rear - Part 1: Requirements, principles of testing |
| VDI 2230 Blatt 1:2003-02 | Systematic calculation of high duty bolted joints - Joints with one cylindrical bolt |
| VDI 3576:2011-03 | Rails for crane systems - Rail connections, rail beddings, rail fastenings, tolerances for crane tracks |
| KTA 3401.2 : 2016(R2017) | STEEL CONTAINMENT VESSELS - PART 2: ANALYSIS AND DESIGN |
| BS EN 50341-2-4:2016 | Overhead electrical lines exceeding AC 1 kV National Normative Aspects (NNA) for Germany (based on EN 50341-1:2012) |
| DIN 18360:2019-09 | German construction contract procedures (VOB) - Part C: General technical specifications in construction contracts (ATV) - Metal construction works |
| DIN 56950-1:2012-05 | ENTERTAINMENT TECHNOLOGY - MACHINERY INSTALLATIONS - PART 1: SAFETY REQUIREMENTS AND INSPECTIONS |
| EN 50341-2-4:2016 | Overhead electrical lines exceeding AC 1 kV - Part 2-4: National Normative Aspects (NNA) for Germany (based on EN 50341-1:2012) |
| DIN 21530-3:2016-09 | MINE SUPPORT - PART 3: REQUIREMENTS |
| DIN 18360:2016-09 | GERMAN CONSTRUCTION CONTRACT PROCEDURES (VOB) - PART C: GENERAL TECHNICAL SPECIFICATIONS IN CONSTRUCTION CONTRACTS (ATV) - METALWORK |
| Z151-17 | Concrete pumps and placing booms |
| DIN HDBK 69/1 : 13ED 2015 | |
| DIN 19704-2:2014-11 | HYDRAULIC STEEL STRUCTURES - PART 2: DESIGN AND MANUFACTURING |
| KTA 3205.2 : 2015 COR 2016 | COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS - PART 2: COMPONENT SUPPORT STRUCTURES WITH NON-INTEGRAL CONNECTIONS FOR PRESSURE AND ACTIVITY-RETAINING COMPONENTS IN SYSTEMS OUTSIDE THE PRIMARY CIRCUIT |
| EN ISO 1479:2011 | Hexagon head tapping screws (ISO 1479:2011) |
| ISO 10511:2012 | Prevailing torque type hexagon thin nuts (with non-metallic insert) |
| ISO 9018:2015 | Destructive tests on welds in metallic materials Tensile test on cruciform and lapped joints |
| ISO/TR 20172:2009 | Welding Grouping systems for materials European materials |
| EN ISO 15609-5:2011 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 5: Resistance welding (ISO 15609-5:2011, Corrected version 2011-12-01) |
| ISO 14555:2017 | Welding — Arc stud welding of metallic materials |
| EN ISO 16432:2007 | Resistance welding - Procedure for projection welding of uncoated and coated low carbon steels using embossed projection(s) (ISO 16432:2006) |
| EN ISO 9692-1:2013 | Welding and allied processes - Types of joint preparation - Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels (ISO 9692-1:2013) |
| EN 14399-8:2007 | High-strength structural bolting assemblies for preloading - Part 8: System HV - Hexagon fit bolt and nut assemblies |
| EN 10162:2003 | Cold rolled steel sections - Technical delivery conditions - Dimensional and cross-sectional tolerances |
| ISO 14341:2010 | Welding consumables Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels Classification |
| ISO 2063:2005 | Thermal spraying Metallic and other inorganic coatings Zinc, aluminium and their alloys |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| ISO 14373:2015 | Resistance welding — Procedure for spot welding of uncoated and coated low carbon steels |
| ISO/TR 3834-6:2007 | Quality requirements for fusion welding of metallic materials — Part 6: Guidelines on implementing ISO 3834 |
| ISO 7090:2000 | Plain washers, chamfered Normal series Product grade A |
| ISO 19840:2012 | Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Measurement of, and acceptance criteria for, the thickness of dry films on rough surfaces |
| EN ISO 5817:2014 | Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2014) |
| EN 1337-6:2004 | Structural bearings - Part 6: Rocker bearings |
| EN ISO 10511:2012 | Prevailing torque type hexagon thin nuts (with non-metallic insert) (ISO 10511:2012) |
| EN 10048:1996 | Hot rolled narrow steel strip - Tolerances on dimensions and shape |
| EN 10051:2010 | Continuously hot-rolled strip and plate/sheet cut from wide strip of non-alloy and alloy steels - Tolerances on dimensions and shape |
| EN ISO 15614-11:2002 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 11: Electron and laser beam welding (ISO 15614-11:2002) |
| ISO 15480:1999 | Hexagon washer head drilling screws with tapping screw thread |
| EN ISO 9445-2:2010 | Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part 2: Wide strip and plate/sheet (ISO 9445-2:2009) |
| EN ISO 7049:2011 | Cross-recessed pan head tapping screws (ISO 7049:2011) |
| EN 508-3:2008 | Roofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 3: Stainless steel |
| ISO 1479:2011 | Hexagon head tapping screws |
| EN ISO 7091:2000 | Plain washers - Normal series - Product grade C (ISO 7091:2000) |
| EN ISO 6789:2003 | Assembly tools for screws and nuts - Hand torque tools - Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure (ISO 6789:2003) |
| EN ISO 7040:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) - Property classes 5, 8 and 10 (ISO 7040:2012) |
| ISO 14343:2017 | Welding consumables — Wire electrodes, strip electrodes, wires and rods for arc welding of stainless and heat resisting steels — Classification |
| ISO 15980:2002 | Open end blind rivets with break pull mandrel and countersunk head — St/St |
| EN 12385-1:2002+A1:2008 | Steel wire ropes - Safety - Part 1: General requirements |
| EN 10140:2006 | Cold rolled narrow steel strip - Tolerances on dimensions and shape |
| ISO 13920:1996 | Welding — General tolerances for welded constructions — Dimensions for lengths and angles — Shape and position |
| EN 10079:2007 | Definition of steel products |
| EN 14399-3:2015 | High-strength structural bolting assemblies for preloading - Part 3: System HR - Hexagon bolt and nut assemblies |
| EN 10025-4:2004 | Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels |
| ISO 10684:2004 | Fasteners — Hot dip galvanized coatings |
| ISO 21670:2014 | Fasteners — Hexagon weld nuts with flange |
| EN ISO 7093-2:2000 | Plain washers - Large series - Part 2: Product grade C (ISO 7093-2:2000) |
| ISO 7042:2012 | Prevailing torque type all-metal hexagon high nuts — Property classes 5, 8, 10 and 12 |
| ISO 4042:1999 | Fasteners Electroplated coatings |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| ISO 15614-13:2012 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 13: Upset (resistance butt) and flash welding |
| EN 10149-1:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General technical delivery conditions |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| ISO 17633:2010 | Welding consumables — Tubular cored electrodes and rods for gas shielded and non-gas shielded metal arc welding of stainless and heat-resisting steels — Classification |
| EN 15048-1:2016 | Non-preloaded structural bolting assemblies - Part 1: General requirements |
| EN ISO 4042:1999 | Fasteners - Electroplated coatings (ISO 4042:1999) |
| ISO 15614-11:2002 | Specification and qualification of welding procedures for metallic materials Welding procedure test Part 11: Electron and laser beam welding |
| EN ISO 7092:2000 | Plain washers - Small series - Product grade A (ISO 7092:2000) |
| EN ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials - Qualification based on pre-production welding test (ISO 15613:2004) |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| ISO 15620:2000 | Welding Friction welding of metallic materials |
| ISO 15983:2002 | Open end blind rivets with break pull mandrel and protruding head — A2/A2 |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| ISO 10447:2015 | Resistance welding — Testing of welds — Peel and chisel testing of resistance spot and projection welds |
| EN ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials - Qualification by adoption of a standard welding procedure (ISO 15612:2004) |
| EN 10268:2006+A1:2013 | Cold rolled steel flat products with high yield strength for cold forming - Technical delivery conditions |
| EN 10056-2:1993 | Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions |
| ISO 14713-1:2017 | Zinc coatings — Guidelines and recommendations for the protection against corrosion of iron and steel in structures — Part 1: General principles of design and corrosion resistance |
| ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on tested welding consumables |
| ISO 8503-2:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure |
| EN 756:2004 | Welding consumables - Solid wires, solid wire-flux and tubular cored electrode-flux combinations for submerged arc welding of non alloy and fine grain steels - Classification |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| EN 10244-2:2009 | Steel wire and wire products - Non-ferrous metallic coatings on steel wire - Part 2: Zinc or zinc alloy coatings |
| EN ISO 15620:2000 | Welding - Friction welding of metallic materials (ISO 15620:2000) |
| ISO 15979:2002 | Open end blind rivets with break pull mandrel and protruding head — St/St |
| EN ISO 7042:2012 | Prevailing torque type all-metal hexagon high nuts - Property classes 5, 8, 10 and 12 (ISO 7042:2012) |
| EN ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles - Specifications and test methods (ISO 1461:2009) |
| ISO 2808:2007 | Paints and varnishes Determination of film thickness |
| EN ISO 1481:2011 | Slotted pan head tapping screws (ISO 1481:2011) |
| ISO/TR 15608:2017 | Welding — Guidelines for a metallic materials grouping system |
| ISO 2320:2015 | Fasteners Prevailing torque steel nuts Functional properties |
| EN ISO 7090:2000 | Plain washers, chamfered - Normal series - Product grade A (ISO 7090:2000) |
| EN 10279:2000 | Hot rolled steel channels - Tolerances on shape, dimensions and mass |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| ISO 2560:2009 | Welding consumables Covered electrodes for manual metal arc welding of non-alloy and fine grain steels Classification |
| EN ISO 9445-1:2010 | Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part 1: Narrow strip and cut lengths (ISO 9445-1:2009) |
| EN ISO 15979:2002 | Open end blind rivets with break pull mandrel and protruding head - St/St (ISO 15979:2002) |
| ISO 15984:2002 | Open end blind rivets with break pull mandrel and countersunk head — A2/A2 |
| ISO 10509:2012 | Hexagon flange head tapping screws |
| EN 1011-1:2009 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| EN 10149-2:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Technical delivery conditions for thermomechanically rolled steels |
| ISO 14731:2006 | Welding coordination Tasks and responsibilities |
| EN 10034:1993 | Structural steel I and H sections - Tolerances on shape and dimensions |
| EN ISO 7719:2012 | Prevailing torque type all-metal hexagon regular nuts - Property classes 5, 8 and 10 (ISO 7719:2012) |
| ISO 7049:2011 | Cross-recessed pan head tapping screws |
| ISO 18276:2017 | Welding consumables — Tubular cored electrodes for gas-shielded and non-gas-shielded metal arc welding of high strength steels — Classification |
| ISO 7976-2:1989 | Tolerances for building — Methods of measurement of buildings and building products — Part 2: Position of measuring points |
| EN 10264-4:2012 | Steel wire and wire products - Steel wire for ropes - Part 4: Stainless steel wire |
| EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
| EN 1337-2:2004 | Structural bearings - Part 2: Sliding elements |
| EN 10346:2015 | Continuously hot-dip coated steel flat products for cold forming - Technical delivery conditions |
| ISO/TR 17663:2001 | Welding Guidelines for quality requirements for heat treatment in connection with welding and allied processes |
| EN ISO 7093-1:2000 | Plain washers - Large series - Part 1: Product grade A (ISO 7093-1:2000) |
| ISO 1461:2009 | Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods |
| PREN 10138-3 : DRAFT 2000 | PRESTRESSING STEELS - PART 3: STRAND |
| EN ISO 16834:2012 | Welding consumables - Wire electrodes, wires, rods and deposits for gas shielded arc welding of high strength steels - Classification (ISO 16834:2012) |
| EN ISO 18276:2017 | Welding consumables - Tubular cored electrodes for gas-shielded and non-gas-shielded metal arc welding of high strength steels - Classification (ISO 18276:2017) |
| EN ISO 15976:2002 | Closed end blind rivets with break pull mandrel and protrudiing head - St/St (ISO 15976:2002) |
| EN 10139:2016 | Cold rolled uncoated low carbon steel narrow strip for cold forming - Technical delivery conditions |
| ISO 3443-2:1979 | Tolerances for building — Part 2: Statistical basis for predicting fit between components having a normal distribution of sizes |
| EN 10080:2005 | Steel for the reinforcement of concrete - Weldable reinforcing steel - General |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| ISO 9013:2017 | Thermal cutting — Classification of thermal cuts — Geometrical product specification and quality tolerances |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| EN ISO 9018:2015 | Destructive tests on welds in metallic materials - Tensile test on cruciform and lapped joints (ISO 9018:2015) |
| EN 10131:2006 | Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| ISO 10005:2005 | Quality management systems Guidelines for quality plans |
| EN 10024:1995 | Hot rolled taper flange I sections - Tolerances on shape and dimensions |
| EN 10210-1:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| EN 1337-8:2007 | Structural bearings - Part 8: Guide Bearings and Restraint Bearings |
| EN 1090-1:2009+A1:2011 | Execution of steel structures and aluminium structures - Part 1: Requirements for conformity assessment of structural components |
| ISO 3834:1978 | Welding — Factors to be considered when assessing firms using welding as a prime means of fabrication |
| EN ISO 1127:1996 | Stainless steel tubes - Dimensions, tolerances and conventional masses per unit length (ISO 1127:1992) |
| ISO 15612:2004 | Specification and qualification of welding procedures for metallic materials Qualification by adoption of a standard welding procedure |
| ISO 5817:2014 | Welding — Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) — Quality levels for imperfections |
| EN ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on previous welding experience (ISO 15611:2003) |
| EN 10163-2:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats |
| EN 1337-11:1997 | Structural bearings - Part 11: Transport, storage and installation |
| ISO 9692-1:2013 | Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels |
| EN ISO 17652-2:2003 | Welding - Test for shop primers in relation to welding and allied processes - Part 2: Welding properties of shop primers (ISO 17652-2:2003) |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| EN ISO 14373:2015 | Resistance welding - Procedure for spot welding of uncoated and coated low carbon steels (ISO 14373:2015) |
| EN 10060:2003 | Hot rolled round steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 1: Arc welding |
| EN 10169:2010+A1:2012 | Continuously organic coated (coil coated) steel flat products - Technical delivery conditions |
| EN ISO 13920:1996 | Welding - General tolerances for welded constructions - Dimensions for lengths and angles - Shape and position (ISO 13920:1996) |
| EN 13438:2013 | Paints and varnishes - Powder organic coatings for hot dip galvanised or sherardised steel products for construction purposes |
| ISO 15611:2003 | Specification and qualification of welding procedures for metallic materials — Qualification based on previous welding experience |
| EN 10219-1:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| ISO 1481:2011 | Slotted pan head tapping screws |
| ISO 16834:2012 | Welding consumables — Wire electrodes, wires, rods and deposits for gas shielded arc welding of high strength steels — Classification |
| EN 10143:2006 | Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape |
| ISO 7089:2000 | Plain washers Normal series Product grade A |
| ISO 16432:2006 | Resistance welding Procedure for projection welding of uncoated and coated low carbon steels using embossed projection(s) |
| ISO 9445-2:2009 | Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 2: Wide strip and plate/sheet |
| EN ISO 14341:2011 | Welding consumables - Wire electrodes and weld deposits for gas shielded metal arc welding of non alloy and fine grain steels - Classification (ISO 14341:2010) |
| EN 10264-3:2012 | Steel wire and wire products - Steel wire for ropes - Part 3: Round and shaped non alloyed steel wire for high duty applications |
| EN 10021:2006 | General technical delivery conditions for steel products |
| EN 13001-1:2015 | Cranes - General design - Part 1: General principles and requirements |
| ISO 4463-1:1989 | Measurement methods for building — Setting-out and measurement — Part 1: Planning and organization, measuring procedures, acceptance criteria |
| ISO 7719:2012 | Prevailing torque type all-metal hexagon regular nuts — Property classes 5, 8 and 10 |
| EN 1559-2:2014 | Founding - Technical conditions of delivery - Part 2: Additional requirements for steel castings |
| ISO 7091:2000 | Plain washers Normal series Product grade C |
| EN 10017:2004 | Steel rod for drawing and/or cold rolling - Dimensions and tolerances |
| CEN ISO/TR 3834-6:2007 | Quality requirements for fusion welding of metallic materials - Part 6: Guidelines on implementing ISO 3834 (ISO/TR 3834-6:2007) |
| EN ISO 2560:2009 | Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and fine grain steels - Classification (ISO 2560:2009) |
| EN ISO 2320:2015 | Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015) |
| EN ISO 21670:2014 | Fasteners - Hexagon weld nuts with flange (ISO 21670:2014) |
| ISO 7092:2000 | Plain washers Small series Product grade A |
| EN ISO 10513:2012 | Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread - Property classes 8, 10 and 12 (ISO 10513:2012) |
| EN 1559-1:2011 | Founding - Technical conditions of delivery - Part 1: General |
| EN ISO 8503-1:2012 | Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces (ISO 8503-1:2012) |
| ISO 10513:2012 | Prevailing torque type all-metal hexagon high nuts with metric fine pitch thread — Property classes 8, 10 and 12 |
| EN ISO 14713-1:2017 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 1: General principles of design and corrosion resistance (ISO 14713-1:2017) |
| EN 14399-6:2015 | High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers |
| EN ISO 8503-2:2012 | Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure (ISO 8503-2:2012) |
| ISO 10512:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread — Property classes 6, 8 and 10 |
| ISO 17632:2015 | Welding consumables Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels Classification |
| ISO 7040:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) — Property classes 5, 8 and 10 |
| EN 10025-5:2004 | Hot rolled products of structural steels - Part 5: Technical delivery conditions for structural steels with improved atmospheric corrosion resistance |
| EN 10163-3:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections |
| EN ISO 14343:2017 | Welding consumables - Wire electrodes, strip electrodes, wires and rods for arc welding of stainless and heat resisting steels - Classification (ISO 14343:2017) |
| EN 1337-3:2005 | Structural bearings - Part 3: Elastomeric bearings |
| EN 13411-4:2011 | Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing |
| EN 760:1996 | Welding consumables - Fluxes for submerged arc welding - Classification |
| EN ISO 14731:2006 | Welding coordination - Tasks and responsibilities (ISO 14731:2006) |
| EN 14399-1:2015 | High-strength structural bolting assemblies for preloading - Part 1: General requirements |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 12062:1997/A2:2003 | NON-DESTRUCTIVE EXAMINATION OF WELDS - GENERAL RULES FOR METALLIC MATERIALS |
| EN 1993-3-2:2006 | Eurocode 3 - Design of steel structures - Part 3-2: Towers, masts and chimneys - Chimneys |
| EN ISO 17632:2015 | Welding consumables - Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloy and fine grain steels - Classification (ISO 17632:2015) |
| ISO 4997:2015 | Cold-reduced carbon steel sheet of structural quality |
| EN 1600:1997 | Welding consumables - Covered electrodes for manual arc welding of stainless and heat resisting steels - Classification |
| EN ISO 15609-1:2004 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 1: Arc welding (ISO 15609-1:2004) |
| EN 14399-4:2015 | High-strength structural bolting assemblies for preloading - Part 4: System HV - Hexagon bolt and nut assemblies |
| EN ISO 2063:2005 | Thermal spraying - Metallic and other inorganic coatings - Zinc, aluminium and their alloys (ISO 2063:2005) |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| EN ISO 16433:2007 | Resistance welding - Procedure for seam welding of uncoated and coated low carbon steels (ISO 16433:2006) |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| ISO 14554-1:2013 | Quality requirements for welding — Resistance welding of metallic materials — Part 1: Comprehensive quality requirements |
| ISO 17652-2:2003 | Welding — Test for shop primers in relation to welding and allied processes — Part 2: Welding properties of shop primers |
| EN 10025-6:2004+A1:2009 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| EN 1713:1998/A2:2003 | NON-DESTRUCTIVE TESTING OF WELDS - ULTRASONIC TESTING - CHARACTERIZATION OF INDICATIONS IN WELDS |
| ISO 14175:2008 | Welding consumables — Gases and gas mixtures for fusion welding and allied processes |
| ISO 7976-1:1989 | Tolerances for building — Methods of measurement of buildings and building products — Part 1: Methods and instruments |
| ISO 15609-5:2011 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 5: Resistance welding |
| ISO 8503-1:2012 | Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces |
| EN ISO 15614-13:2012 | Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 13: Upset (resistance butt) and flash welding (ISO 15614-13:2012) |
| EN 10020:2000 | Definition and classification of grades of steel |
| ISO 6789:2003 | Assembly tools for screws and nuts Hand torque tools Requirements and test methods for design conformance testing, quality conformance testing and recalibration procedure |
| ISO 15976:2002 | Closed end blind rivets with break pull mandrel and protruding head — St/St |
| EN 10219-2:2006 | Cold formed welded structural hollow sections of non-alloy and fine grain steels - Part 2: Tolerances, dimensions and sectional properties |
| ISO 3443-1:1979 | Tolerances for building — Part 1: Basic principles for evaluation and specification |
| EN 12385-10:2003+A1:2008 | Steel wire ropes - Safety - Part 10: Spiral ropes for general structural applications |
| EN 14399-7:2007 | High-strength structural bolting assemblies for preloading - Part 7: System HR - Countersunk head bolt and nut assemblies |
| EN 10061:2003 | Hot rolled hexagon steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| EN 10059:2003 | Hot rolled square steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| EN 1337-7:2004 | Structural bearings - Part 7: Spherical and cylindrical PTFE bearings |
| CEN/TR 10347:2006 | Guidance for forming of structural steels in processing |
| ISO 16433:2006 | Resistance welding Procedure for seam welding of uncoated and coated low carbon steels |
| ISO 9692-2:1998 | Welding and allied processes — Joint preparation — Part 2: Submerged arc welding of steels |
| EN ISO 15609-4:2009 | Specification and qualification of welding procedures for metallic materials - Welding procedure specification - Part 4: Laser beam welding (ISO 15609-4:2009) |
| EN ISO 15980:2002 | Open end blind rivets with break pull mandrel and countersunk head - St/St (ISO 15980:2002) |
| ISO 7093-2:2000 | Plain washers Large series Part 2: Product grade C |
| EN 14399-5:2015 | High-strength structural bolting assemblies for preloading - Part 5: Plain washers |
| EN 14295 : 2003 | WELDING CONSUMABLES - WIRE AND TUBULAR CORED ELECTRODES AND ELECTRODE-FLUX COMBINATIONS FOR SUBMERGED ARC WELDING OF HIGH STRENGTH STEELS - CLASSIFICATION |
| ISO 15613:2004 | Specification and qualification of welding procedures for metallic materials Qualification based on pre-production welding test |
| ISO 4063:2009 | Welding and allied processes — Nomenclature of processes and reference numbers |
| EN ISO 15480:1999 | Hexagon washer head drilling screws with tapping screw thread (ISO 15480:1999) |
| EN ISO 636:2017 | Welding consumables - Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels - Classification (ISO 636:2017) |
| ISO 14713-2:2009 | Zinc coatings Guidelines and recommendations for the protection against corrosion of iron and steel in structures Part 2: Hot dip galvanizing |
| EN 10055:1995 | Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions |
| EN ISO 14555:2017 | Welding - Arc stud welding of metallic materials (ISO 14555:2017) |
| EN ISO 15610:2003 | Specification and qualification of welding procedures for metallic materials - Qualification based on tested welding consumables (ISO 15610:2003) |
| ISO 3443-3:1987 | Tolerances for building — Part 3: Procedures for selecting target size and predicting fit |
| EN ISO 9013:2017 | Thermal cutting - Classification of thermal cuts - Geometrical product specification and quality tolerances (ISO 9013:2017) |
| EN 571-1:1997 | Non destructive testing - Penetrant testing - Part 1: General principles |
| ISO 9445-1:2009 | Continuously cold-rolled stainless steel Tolerances on dimensions and form Part 1: Narrow strip and cut lengths |
| EN 1418:1997 | Welding personnel - Approval testing of welding operators for fusion welding and resistance weld setters for fully mechanized and automatic welding of metallic materials |
| EN ISO 7089:2000 | Plain washers - Normal series - Product grade A (ISO 7089:2000) |
| EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
| ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts |
| ISO 13916:2017 | Welding — Measurement of preheating temperature, interpass temperature and preheat maintenance temperature |
| EN 970:1997 | Non-destructive examination of fusion welds - Visual examination |
| ISO 1803:1997 | Building construction Tolerances Expression of dimensional accuracy Principles and terminology |
| EN ISO 15984:2002 | Open end blind rivets with break pull mandrel and countersunk head - A2/A2 (ISO 15984:2002) |
| EN 1290:1998/A2:2003 | NON-DESTRUCTIVE EXAMINATION OF WELDS - MAGNETIC PARTICLE EXAMINATION OF WELDS |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| EN 1337-5:2005 | Structural bearings - Part 5: Pot bearings |
| ISO 2859-5:2005 | Sampling procedures for inspection by attributes — Part 5: System of sequential sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection |
| EN ISO 15983:2002 | Open end blind rivets with break pull mandrel and protruding head - A2/A2 (ISO 15983:2002) |
| ISO 15609-4:2009 | Specification and qualification of welding procedures for metallic materials Welding procedure specification Part 4: Laser beam welding |
| ISO 636:2017 | Welding consumables — Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine-grain steels — Classification |
| EN 13670:2009 | Execution of concrete structures |
| EN 15311:2007 | Thermal spraying - Components with thermally sprayed coatings - Technical supply conditions |
| EN ISO 10512:2012 | Prevailing torque type hexagon regular nuts (with non-metallic insert) with metric fine pitch thread - Property classes 6, 8 and 10 (ISO 10512:2012) |
| EN 14616:2004 | Thermal spraying - Recommendations for thermal spraying |
| EN 10149-3:2013 | Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Technical delivery conditions for normalized or normalized rolled steels |
| EN ISO 9000:2015 | Quality management systems - Fundamentals and vocabulary (ISO 9000:2015) |
| EN 757:1997 | Welding consumables - Covered electrodes for manual metal arc welding of high strength steels - Classification |
| EN ISO 10447:2015 | Resistance welding - Testing of welds - Peel and chisel testing of resistance spot and projection welds (ISO 10447:2015) |
| EN 13479:2017 | Welding consumables - General product standard for filler metals and fluxes for fusion welding of metallic materials |
| EN ISO 2808:2007 | Paints and varnishes - Determination of film thickness (ISO 2808:2007) |
| EN 508-1:2014 | Roofing and cladding products from metal sheet - Specification for self-supporting of steel, aluminium or stainless steel sheet - Part 1: Steel |
| EN 14399-2:2015 | High-strength structural bolting assemblies for preloading - Part 2: Suitability for preloading |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 1127:1992 | Stainless steel tubes Dimensions, tolerances and conventional masses per unit length |
| ISO 7093-1:2000 | Plain washers Large series Part 1: Product grade A |
| EN ISO 14713-2:2009 | Zinc coatings - Guidelines and recommendations for the protection against corrosion of iron and steel in structures - Part 2: Hot dip galvanizing (ISO 14713-2:2009) |
| EN ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009) |
| EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
| EN ISO 14175:2008 | Welding consumables - Gases and gas mixtures for fusion welding and allied processes (ISO 14175:2008) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.