DIN EN 10225:2009-10
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
WELDABLE STRUCTURAL STEELS FOR FIXED OFFSHORE STRUCTURES - TECHNICAL DELIVERY CONDITIONS
Hardcopy , PDF
07-03-2021
DIN EN 10225-1:2019-11
DIN EN 10225-3:2019-11
DIN EN 10225-4:2019-11
DIN EN 10225-2:2019-11
English
01-01-2009
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Vorwort
1 Anwendungsbereich
2 Normative Verweisungen
3 Begriffe
4 Bestellangaben
5 Masse, Masse und Grenzabmasse
6 Einteilung und Bezeichnung
7 Herstellungsverfahren
8 Anforderungen
9 Prüfung
10 Probenahme
11 Prüfverfahren
12 Kennzeichnung, Bündelung und
Oberflächenschutz
13 Zusätzliche Anforderungen
Anhang A (normativ) Lage der Probenabschnitte
für den Zugversuch und den
Kerbschlagbiegeversuch
Anhang B (normativ) Lage der Proben für den
Zugversuch, wenn nicht beide gewalzten
Oberflächen beibehalten werden können
Anhang C (normativ, wenn die zusätzliche Anforderung
2 vom Käufer verlangt wird) Einzelheiten zum
Herstellungsverfahren, die vom Hersteller bei
Stählen der Gruppen 2 und 3 angegeben
werden müssen
Anhang D (normativ, wenn die zusätzliche Anforderung
16 vom Käufer verlangt wird) Kaltumformbarkeit
für Stahlbleche der Gruppen 2 und 3
Anhang E (normativ, wenn die zusätzliche Anforderung
18 vom Käufer verlangt wird) Prüfung der
Schweisseignung bei Stählen der Gruppen 2 und
3 und mechanische Prüfung von
Stumpfnahtschweissungen
Anhang F (normativ, wenn die zusätzliche Anforderung
18 vom Käufer verlangt wird) Schweisseignungsprüfung
bei Stählen der Gruppen 2 und 3 -Auftragsschweissung
Anhang G (normativ, wenn die zusätzliche Anforderung 18 vom
Käufer verlangt wird) Schweisseignungsprüfung bei
Stählen der Gruppen 2 und 3 - CTS-Versuche
Literaturhinweise
This Standard is included in DIN Handbook 402 E. Describes requirements for weldable structural steels to be used in the fabrication of fixed offshore structures in the form of plates up to and including 150 mm thick.
| DevelopmentNote |
Supersedes SEW 085 (11/2003)
|
| DocumentType |
Standard
|
| Pages |
78
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NF EN 10225 : 2009 | Identical |
| SN EN 10225 : 2009 | Identical |
| NS EN 10225 : 2009 | Identical |
| EN 10225:2009 | Identical |
| UNI EN 10225 : 2009 | Identical |
| NBN EN 10225 : 2009 | Identical |
| BS EN 10225:2009 | Identical |
| UNE-EN 10225:2010 | Identical |
| I.S. EN 10225:2009 | Identical |
| NEN EN 10225 : 2009 | Identical |
| DIN 71501:1992-05 | OVAL FLANGES FOR MOTOR VEHICLES |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| EN ISO 12737:2010 | Metallic materials - Determination of plane-strain fracture toughness (ISO 12737:2010) |
| EN ISO 14284:2002 | Steel and iron - Sampling and preparation of samples for the determination of chemical composition (ISO 14284:1996) |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| EN 10052:1993 | Vocabulary of heat treatment terms for ferrous products |
| EN 10079:2007 | Definition of steel products |
| EN 10025-4:2004 | Hot rolled products of structural steels - Part 4: Technical delivery conditions for thermomechanical rolled weldable fine grain structural steels |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| EN 10029:2010 | Hot-rolled steel plates 3 mm thick or above - Tolerances on dimensions and shape |
| EN 10056-2:1993 | Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions |
| EN 10164:2004 | Steel products with improved deformation properties perpendicular to the surface of the product - Technical delivery conditions |
| EN 10246-12:2000 | Non-destructive testing of steel tubes - Part 12: Magnetic particle inspection of seamless and welded ferromagnetic steel tubes for the detection of surface imperfections |
| EN 10279:2000 | Hot rolled steel channels - Tolerances on shape, dimensions and mass |
| EN 10256:2000 | Non-destructive testing of steel tubes - Qualification and competence of level 1 and 2 non-destructive testing personnel |
| EN ISO 6947:2011 | Welding and allied processes - Welding positions (ISO 6947:2011) |
| EN 1011-1:2009 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| EN 10034:1993 | Structural steel I and H sections - Tolerances on shape and dimensions |
| EN ISO 4063:2010 | Welding and allied processes - Nomenclature of processes and reference numbers (ISO 4063:2009, Corrected version 2010-03-01) |
| EN ISO 2566-1:1999 | Steel - Conversion of elongation values - Part 1: Carbon and low alloy steels (ISO 2566-1:1984) |
| ISO 12737:2010 | Metallic materials Determination of plane-strain fracture toughness |
| EN 895:1995 | Destructive tests on welds in metallic materials - Transverse tensile test |
| EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
| EN 473:2008 | Non-destructive testing - Qualification and certification of NDT personnel - General principles |
| EN 10024:1995 | Hot rolled taper flange I sections - Tolerances on shape and dimensions |
| EN 10210-1:2006 | Hot finished structural hollow sections of non-alloy and fine grain steels - Part 1: Technical delivery conditions |
| EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
| EN ISO 9934-1:2016 | Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2016) |
| EN 10306:2001 | Iron and steel - Ultrasonic testing of H beams with parallel flanges and IPE beams |
| EN 10163-2:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 2: Plate and wide flats |
| ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
| DIN 1026-1:2009-09 | Hot rolled steel channels - Part 1: Taper flange steel channels - Dimensions, masses and sectional properties |
| EN 10246-7:2005 | Non-destructive testing of steel tubes - Part 7: Automatic full peripheral ultrasonic testing of seamless and welded (except submerged arc welded) tubes for the detection of longitudinal imperfections |
| EN 10021:2006 | General technical delivery conditions for steel products |
| BS 7363:1990 | Method for bead-on-plate (BOP) test for welds |
| ISO 2566-1:1984 | Steel Conversion of elongation values Part 1: Carbon and low alloy steels |
| ISO 9934-1:2016 | Non-destructive testing — Magnetic particle testing — Part 1: General principles |
| EN 10163-3:2004 | Delivery requirements for surface condition of hot-rolled steel plates, wide flats and sections - Part 3: Sections |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 10246-3:1999 | Non-destructive testing of steel tubes - Part 3: Automatic eddy current testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of imperfections |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| ISO 8492:2013 | Metallic materials Tube Flattening test |
| EN 10025-6:2004+A1:2009 | Hot rolled products of structural steels - Part 6: Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition |
| EN 10020:2000 | Definition and classification of grades of steel |
| EN ISO 8492:2013 | Metallic materials - Tube - Flattening test (ISO 8492:2013) |
| EN 10246-15:2000 | Non-destructive testing of steel tubes - Part 15: Automatic ultrasonic testing of strip/plate used in the manufacture of welded steel tubes for the detection of laminar imperfections |
| EN 10246-14:1999 | Non-destructive testing of steel tubes - Part 14: Automatic ultrasonic testing of seamless and welded (except submerged arc-welded) steel tubes for the detection of laminar imperfections |
| ISO 4063:2009 | Welding and allied processes — Nomenclature of processes and reference numbers |
| EN 10055:1995 | Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions |
| EN 571-1:1997 | Non destructive testing - Penetrant testing - Part 1: General principles |
| EN 10160:1999 | Ultrasonic testing of steel flat product of thickness equal or greater than 6 mm (reflection method) |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| EN 10067:1996 | Hot rolled bulb flats - Dimensions and tolerances on shape, dimensions and mass |
| ISO 14284:1996 | Steel and iron — Sampling and preparation of samples for the determination of chemical composition |
| EN 10246-8:1999 | Non-destructive testing of steel tubes - Part 8: Automatic ultrasonic testing of the weld seam of electric welded steel tubes for the detection of longitudinal imperfections |
| ISO 6947:2011 | Welding and allied processes Welding positions |
| EN 10246-5 : 1999 | NON-DESTRUCTIVE TESTING OF STEEL TUBES - PART 5: AUTOMATIC FULL PERIPHERAL MAGNETIC TRANSDUCER/FLUX LEAKAGE TESTING OF SEAMLESS AND WELDED (EXCEPT SUBMERGED ARC WELDED) FERROMAGNETIC STEEL TUBES FOR THE DETECTION OF LONGITUDINAL IMPERFECTIONS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.