DEFSTAN 80-16/4(2006) : 2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
PAINT REMOVER, DICHLOROMETHANE, WATER RINSABLE TYPE - TYPE 1: HIGH VISCOSITY (BRUSHING) TYPE 2: LOW VISCOSITY (SPRAYING)
Hardcopy , PDF
15-04-2011
English
01-01-2006
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Introduction
1 Scope
2 Warning
3 Normative References
4 Description
5 Information to be Supplied by the Purchaser
6 Keeping Qualities
7 Quality Assurance
8 Product Conformity Certification
9 Containers and Marking of Containers
10 Composition
11 Testing
11.1 Test Conditions
11.2 Condition
11.3 Test Requirements
Annex A - Determination of Viscosity
Annex B - Determination of Rate of Evaporation
Annex C - Determination of Freedom from Corrosive Action
Annex D - Determination of Paint Removing Power
Annex E - Determination of Flammability
Annex F - Determination of Water Rinsability
Annex G - Determination of Stress Corrosion Cracking
Annex H - Determination of Resistance to Hydrogen Embrittlement
Describes a requirement for Product Conformity Certification (PCC).
| DevelopmentNote |
Supersedes DEFSTAN 80-16/3(2002) (09/2006)
|
| DocumentType |
Standard
|
| Pages |
20
|
| PublisherName |
UK Ministry of Defence Standards
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| BS EN ISO 1514:2004 | Paints and varnishes. Standard panels for testing |
| BS EN ISO 1518:2001 | Paints and varnishes. Scratch test |
| DEFSTAN 03-19/3(2005) : 2005 | ELECTRO-DEPOSITION OF CADMIUM |
| BS EN ISO 3696:1995 | Water for analytical laboratory use. Specification and test methods |
| BS 2X 34:1998 | Specification for two component polyurethane finish for aerospace purposes |
| BS EN 23270:1991 | Specification for temperatures and humidities for conditioning and testing paints, varnishes and their raw materials |
| BS EN 2832:1993 | Hydrogen embrittlement of steels. Notched specimen test |
| BS 2L 97:1971 | Specification for plate of aluminium-copper-magnesium-manganese alloy (solution treated, controlled stretched and aged at room temperature) (Cu 4.4, Mg 1.5, Mn 0.6) |
| BS EN 10130:2006 | Cold rolled low carbon steel flat products for cold forming. Technical delivery conditions |
| BS EN 1652:1998 | Copper and copper alloys. Plate, sheet, strip and circles for general purposes |
| BS 2L 500:1973 | Procedure for inspection and testing of wrought magnesium-base alloys |
| DEFSTAN 03-2/4(2005) : 2005 | CLEANING AND PREPARATION OF METAL SURFACES |
| BS L 168:1978 | Specification for bars and extruded sections of aluminium-copper-magnesium-silicon-manganese alloy (solution treated and artificially aged) (not exceeding 200 mm diameter or minor sectional dimension) (Cu 4.4, Mg 0.5, Si 0.7, Mn 0.8) |
| BS EN ISO/IEC 17050-1:2010 | Conformity assessment. Suppliers declaration of conformity General requirements |
| BS 2X 33:1998 | Specification for two component epoxy primer for aerospace purposes |
| DEFSTAN 91-16/2(1982) : 1982 | WAX, PARAFFIN, ORDINARY WAX, PARAFFIN, LF QUALITY WAX, PARAFFIN, SPECIAL |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.