DEFSTAN 02-711/2(2006) : 2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
DETERMINATION OF THE SMOKE INDEX OF THE PRODUCTS OF COMBUSTION FROM SMALL SPECIMENS OF MATERIALS
Hardcopy , PDF
03-02-2012
English
01-01-2006
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Warning
3 Normative References
4 Principle
5 Definitions
6 General description of the test method
7 Apparatus and ancillary equipment
7.1 General
7.2 Test chamber (inc. Figure 1 - multi-jet burner)
8 Test specimens
8.1 Applicability
8.2 Number of test specimens
8.3 Dimensions of test specimens
8.4 Form of test specimens
8.5 Mounting of test specimens
8.6 Conditioning of test specimens
9 Safety of operators
10 Setting-up and calibration procedures
10.1 Chamber wall temperature
10.2 Multi-jet burner set-up
10.3 Test environment
10.4 Determination of percentage light transmission
corresponding to D[s] = 792
11 Test procedure
12 Calculation
12.1 Calculation of specific optical density
12.2 Upper limit on specific optical density
12.3 Correction of results
12.4 Calculation of Smoke Index
13 Test report
Annex A - Informative References
Annex B - Form of test specimens
Annex C - Preparation of test specimens - Paint
C.1 Preparation of test specimens
Annex D - Preparation of test specimens - Tubes and pipes
D.1 Materials available as flat sheet
D.2 Materials only available as tube or pipe
D.2.1 Flat specimens cut from tube or pipe
D.2.2 Specimens cut from tube or pipe samples
D.2.2.1 Outer diameter <= 25 mm
D.2.2.2 Outer diameter > 25 mm
Annex E - Preparation of test specimens - Insulated wires
E.1 Preparation of test specimens
Provides the requirements for one of a series of test methods for determining the fine characteristics of materials.
| DevelopmentNote |
Supersedes DEFSTAN 02-711/1(2000) (05/2006)
|
| DocumentType |
Standard
|
| Pages |
30
|
| PublisherName |
UK Ministry of Defence Standards
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| DEFSTAN 80-134/4(2008) : 2008 | PAINT SYSTEM, ANTI-SLIP FOR SHIPS DECKING, MULTI-PACK - TYPE 1: MEDIUM TEXTURE (HANGAR DECKS, WEATHER DECKS) - TYPE 2: ROUGH TEXTURE (FLIGHT DECKS) |
| DEFSTAN 02-137/2(2007) : 2007 | REQUIREMENTS FOR FOAM COMPONENTS FOR CUSHIONS AND UPHOLSTERY |
| DEFSTAN 02-881 SUPP001/1(2011) : 2011 | LOW FIRE HAZARD CABLE CONDUIT SYSTEMS FOR USE ON SHIPS - SUPPLEMENT 1: PLIABLE CONDUIT SYSTEMS |
| DEFSTAN 02-129/2(2007) : 2007 | REQUIREMENTS FOR SOFT FURNISHINGS AND UPHOLSTERY FABRICS |
| DEFSTAN 47-32/2(2011) : 2011 | RUBBER HOSE AND HOSE ASSEMBLIES FOR FLUID POWER SYSTEMS |
| DEFSTAN 02-130/1(2007) : 2007 | REQUIREMENTS FOR DECORATIVE LININGS AND COMPOSITE BULKHEADS |
| DEFSTAN 07-247(PT1)/2(2006) : 2006 | THE SELECTION OF MATERIALS ON THE BASIS OF THEIR FIRE CHARACTERISTICS - PART 1: SELECTION OF MATERIALS ON THE BASIS OF THEIR FIRE CHARACTERISTICS |
| DEFSTAN 02-802/1(2008) : 2008 | REQUIREMENTS FOR MINERAL WOOL PRODUCTS FOR ACOUSTIC AND THERMAL INSULATION |
| DEFSTAN 61-12(PT0)/3(2011) : 2011 | WIRES, CORDS AND CABLES ELECTRICAL METRIC UNITS - PART 0: GENERAL REQUIREMENTS AND TEST METHODS GENERIC SPECIFICATION |
| MIL-DTL-24640 Revision C:2011 | CABLES, LIGHTWEIGHT, LOW SMOKE, ELECTRIC, FOR SHIPBOARD USE, GENERAL SPECIFICATION FOR |
| DEFSTAN 61-12(PT0)/2(2006) : 2006 | WIRES, CORDS AND CABLES, ELECTRICAL - PART 0: GENERAL REQUIREMENTS AND TEST METHODS - GENERAL SPECIFICATION |
| DEFSTAN 07-247(PT1)/3(2009) : 2009 | THE SELECTION OF MATERIALS ON THE BASIS OF THEIR FIRE CHARACTERISTICS - PART 1: SELECTION OF MATERIALS ON THE BASIS OF THEIR FIRE CHARACTERISTICS |
| DEFSTAN 02-806/2(2010) : 2010 | REQUIREMENTS FOR CERAMIC PRODUCTS FOR THERMAL INSULATION APPLICATIONS: CERAMIC ROPE AND CERAMIC BLANKET |
| DEFSTAN 02-167/4(2011) : 2011 | REQUIREMENT FOR RESIN FOR USE IN SHIPS, BOATS, CRAFT AND CRAFT STRUCTURES |
| DEFSTAN 02-167/3(2007) : 2007 | REQUIREMENTS FOR RESIN FOR USE IN SHIPS, BOATS, CRAFT AND CRAFT STRUCTURES |
| DEFSTAN 02-805/1(2010) : 2010 | REQUIREMENTS FOR VAPOUR BARRIER COATINGS AND PROPRIETARY FLEXIBLE MASTIC SEALERS FOR USE ON INSULATION MATERIALS |
| DEFSTAN 02-851/2(2007) : 2007 | REQUIREMENTS FOR CARPETS - TUFTED CONSTRUCTION |
| DEFSTAN 02-803/1(2010) : 2010 | REQUIREMENTS FOR POLYMER FOAMS FOR THERMAL INSULATION |
| DEFSTAN 02-165/2(2010) : 2010 | REQUIREMENTS FOR SPRING INTERIOR MATTRESSES FOR USE IN SURFACE SHIPS AND SUBMARINES |
| DEFSTAN 02-804/1(2008) : 2008 | REQUIREMENTS FOR CORK PRODUCTS FOR THERMAL INSULATION |
| DEFSTAN 02-881/1(2011) : 2011 | LOW FIRE HAZARD CABLE CONDUIT SYSTEMS FOR USE ON SHIPS |
| DEFSTAN 02-526/2(2008) : 2008 | REQUIREMENTS FOR CABLES ELECTRIC, ELASTOMERIC, LIMITED FIRE HAZARD SHEATHED FOR GENERAL SERVICES |
| DEFSTAN 02-510/1(2006) : 2006 | REQUIREMENTS FOR CABLE GLANDS IN BULKHEADS AND DECKS OF SURFACE SHIPS |
| BS EN ISO 1514:2004 | Paints and varnishes. Standard panels for testing |
| BS 4G 198-3:1999 | Sleeves and moulded components for aircraft electric cables and equipment wires Specification for heat-shrinkable sleeving for binding, insulation, and identification |
| BS EN ISO 13943:2017 | Fire safety. Vocabulary |
| BS EN ISO 5659-2:2017 | Plastics. Smoke generation Determination of optical density by a single-chamber test |
| BS 6401:1983 | Method for measurement, in the laboratory, of the specific optical density of smoke generated by materials |
| DEFSTAN 61-12(PT10)/1(1974) : 1974 | WIRES, CORDS, AND CABLES, ELECTRICAL - METRIC UNITS - PART 10: PVC INSULATED CABLES FOR ROAD VEHICLES |
| DEFSTAN 61-12(PT0)/1(1992) : 1992 | WIRES CORDS AND CABLES ELECTRICAL - METRIC UNITS - PART 0: GENERAL REQUIREMENTS AND TEST METHODS FOR QUALIFICATION APPROVAL - GENERIC SPECIFICATION |
| STANAG 4602 : 2004 | FIRE ASSESSMENT OF MATERIALS |
| BS G 198-5:1997 | Sleeves and moulded components for aircraft electric cables and equipment wires Specification for heat shrinkable moulded shapes |
| ASTM E 662 : 2017-02 | TEST METHOD FOR SPECIFIC OPTICAL DENSITY OF SMOKE GENERATED BY SOLID MATERIALS |
| DEFSTAN 07-247/1(2000) : 2000 | SELECTION OF MATERIALS ON THE BASIS OF THEIR FIRE CHARACTERISTICS - CATEGORY 2 |
| BS EN ISO 291:2008 | Plastics. Standard atmospheres for conditioning and testing |
| AFAP-2 : 2010 | NATO REACTION-TO-FIRE TESTS FOR MATERIALS - SMOKE GENERATION |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.