• Shopping Cart
    There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

DD IEC/TS 60695-11-3:2004

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by

Fire hazard testing Test flames. 500 W flames. Apparatus and confirmational test methods

Available format(s)

Hardcopy , PDF

Superseded date

30-11-2012

Superseded by

BS EN 60695-11-3:2012

Language(s)

English

Published date

24-06-2004

£232.00
Excluding VAT

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Method A - Production of a standardized 500 W nominal
   test flame based on existing hardware
   4.1 Requirements
   4.2 Apparatus and fuel
        4.2.1 Burner
        4.2.2 Flowmeter
        4.2.3 Manometer
        4.2.4 Control valve
        4.2.5 Copper block
        4.2.6 Thermocouple
        4.2.7 Temperature/time indicating/recording and
               timing devices
        4.2.8 Fuel gas
        4.2.9 Laboratory fumehood/chamber
   4.3 Production of test flame
   4.4 Confirmation of the test flame
        4.4.1 Principle
        4.4.2 Procedure
        4.4.3 Verification
5 Method B (withdrawn)
6 Method C - Production of a standardized 500 W nominal
   test flame based based on non-adjustable hardware
   6.1 Requirements
   6.2 Apparatus and fuel
        6.2.1 Burner
        6.2.2 Flowmeters
        6.2.3 Manometer
        6.2.4 Control valves
        6.2.5 Copper block
        6.2.6 Thermocouple
        6.2.7 Temperature/time indicating/recording and
               timing devices
        6.2.8 Fuel gas
        6.2.9 Air supply
        6.2.10 Laboratory fumehood/chamber
   6.3 Production of test flame
   6.4 Confirmation of the test flame
        6.4.1 Principle
        6.4.2 Procedure
        6.4.3 Verification
7 Method D (withdrawn)
8 Classification and designation
Annex A (informative) Test method A arrangement
Annex B (withdrawn)
Annex C (normative) Test method C arrangement
Annex D (withdrawn)
Annex E (informative) Recommended arrangements for the
                       use of the test flames
Annex F (informative) Test arrangements for tests on equipment
Annex G (informative) Test arrangements for tests on material
Annex H (informative) Access to equipment manufacturers and
                       suppliers
Bibliography

Provides detailed requirements for the production of a 500 W nominal, pre-mixed type test flame. The approximate overall height is 125 mm.

Committee
GEL/89
DocumentType
Standard
Pages
36
PublisherName
British Standards Institution
RevisionOf
Status
Superseded
SupersededBy

Provides detailed requirements for the production of a 500 W nominal, pre-mixed type test flame. The approximate overall height is 125 mm. Two test flames are described: Method A may only be produced using methane whereas method C may be produced using either methane or propane. The main changes with respect to the previous edition are described below: - The introduction has been revised, - Test methods B and D have been withdrawn. Test methods A and C have been retained with their original letter designation, - Normative reference ISO 1337 has been withdrawn without a replacement by ISO/TC 26. The callout Cu-ETP UNS 11000 is the replacement for all references to ISO 1337. It is taken from ASTM B187-00 and describes high conductivity electrolytic copper, - A new Annex H has been added which provides access to equipment manufacturers and suppliers,- Alignment with other publications in the IEC 60695-11 series has been made, where appropriate. Has the status of a basic safety publication in accordance with IEC Guide 104.

Standards Relationship
IEC TS 60695-11-3:2004 Identical

IEC 60695-11-4:2011 Fire hazard testing - Part 11-4: Test flames - 50 W flame - Apparatus and confirmational test method
IEC 60695-1-30:2017 Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines
IEC 60695-1-1:1999 Fire hazard testing - Part 1-1: Guidance for assessing the fire hazard of electrotechnical products - General guidelines
IEC 60695-4:2012 Fire hazard testing - Part 4: Terminology concerning fire tests for electrotechnical products
ISO 13943:2017 Fire safety — Vocabulary
IEC 60695-11-2:2017 Fire hazard testing - Part 11-2: Test flames - 1 kW pre-mixed flame - Apparatus, confirmatory test arrangement and guidance
ISO/IEC Guide 51:2014 Safety aspects — Guidelines for their inclusion in standards
IEC GUIDE 104:2010 The preparation of safety publications and the use of basic safety publications and group safety publications
IEC 60584-1:2013 Thermocouples - Part 1: EMF specifications and tolerances

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.