CEI EN 60099-5 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SURGE ARRESTERS - PART 5: SELECTION AND APPLICATION RECOMMENDATIONS
Hardcopy , PDF
22-03-2019
English
01-01-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 General principles for the application of surge arresters
5 Surge arrester fundamentals and applications issues
6 Insulation coordination and surge arrester applications
7 Surge arresters for special applications
8 Asset management of surge arresters
Annex A (informative) - Determination of temporary
overvoltages due to earth faults
Annex B (informative) - Current practice
Annex C (informative) - Arrester modelling techniques for
studies involving insulation coordination and
energy requirements
Annex D (informative) - Diagnostic indicators of metal-oxide
surge arresters in service
Annex E (informative) - Typical data needed from arrester
manufacturers for proper selection of surge arresters
Annex F (informative) - Typical maximum residual voltages
for metal-oxide arresters without gaps according
to IEC 60099-4
Annex G (informative) - Steepness reduction of incoming
surge with additional line terminal surge capacitance
Annex H (informative) - End of life and replacement of old
gapped SiC-arresters
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding
European publications
Gives information, guidance, and recommendations for the selection and application of surge arresters to be used in three-phase systems with nominal voltages above 1 kV.
| Committee |
CT 37
|
| DevelopmentNote |
Classificazione CEI 37-3. (08/2001)
|
| DocumentType |
Standard
|
| Pages |
152
|
| PublisherName |
Comitato Elettrotecnico Italiano
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| IEC 60099-5:2013 | Identical |
| EN 60099-5:2013 | Identical |
| IEC 62271-200:2011 | High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV |
| EN 62271-1:2017 | High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear |
| IEC 60099-4:2014 | Surge arresters - Part 4: Metal-oxide surge arresters without gaps for a.c. systems |
| IEC TR 60071-4:2004 | Insulation co-ordination - Part 4: Computational guide to insulation co-ordination and modelling of electrical networks |
| IEC TS 60815-2:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 2: Ceramic and glass insulators for a.c. systems |
| EN 62271-203:2012 | High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV |
| IEC TR 62271-300:2006 | High-voltage switchgear and controlgear - Part 300: Seismic qualification of alternating current circuit-breakers |
| EN 60099-4:2014 | Surge arresters - Part 4: Metal-oxide surge arresters without gaps for a.c. systems |
| IEC 60099-6:2002 | Surge arresters - Part 6: Surge arresters containing both series and parallel gapped structures - Rated 52 kV and less |
| EN 60507:2014 | Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems |
| IEC 62271-203:2011 | High-voltage switchgear and controlgear - Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV |
| EN 60071-1:2006/A1:2010 | INSULATION CO-ORDINATION - PART 1: DEFINITIONS, PRINCIPLES AND RULES |
| IEC 62271-1:2017 | High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear |
| IEC 60071-2:1996 | Insulation co-ordination - Part 2: Application guide |
| IEC 60099-8:2017 | Surge arresters - Part 8: Metal-oxide surge arresters with external series gap (EGLA) for overhead transmission and distribution lines of a.c. systems above 1 kV |
| EN 60071-2:1997 | Insulation co-ordination - Part 2: Application guide |
| IEC 60507:2013 | Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems |
| IEC 60071-1:2006+AMD1:2010 CSV | Insulation co-ordination - Part 1: Definitions, principles and rules |
| IEC TS 60815-1:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 1: Definitions, information and general principles |
| EN 62271-200:2012/AC:2015 | HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 200: AC METAL-ENCLOSED SWITCHGEAR AND CONTROLGEAR FOR RATED VOLTAGES ABOVE 1 KV AND UP TO AND INCLUDING 52 KV (IEC 62271-200:2011) |
| IEC TS 60815-3:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 3: Polymer insulators for a.c. systems |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.