BS EN ISO 9445:2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Continuously cold-rolled stainless steel narrow strip, wide strip, plate/sheet and cut lengths. Tolerances on dimensions and form
Hardcopy , PDF
31-03-2010
English
31-08-2006
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative reference
3 Terms and definitions
4 Information to be supplied by the purchaser
5 Type of delivery and delivery condition
6 Preferred thicknesses
7 Tolerances on thickness
8 Tolerances on width
9 Preferred coil inner diameters for cold-rolled products
10 Tolerances on length
11 Tolerances on edge camber
12 Tolerances on squareness
13 Tolerances on flatness
14 Edge waviness tolerances for cold-rolled strip
15 Form of coils
16 Ordered format for plate/sheet and cut lengths
17 Measurement of thickness
18 Measurement of width
19 Measurement of length
20 Measurement of edge camber
21 Measurement of squareness
22 Measurement of flatness and waviness
Describes the tolerances on dimensions and form for continuously cold-rolled stainless steel narrow strip, in thicknesses of up to and including 3 mm and in rolling widths of less than 600 mm. It also applies to cut lengths taken from such strip.
| Committee |
ISE/105
|
| DevelopmentNote |
Supersedes BS EN 10258 and BS EN 10259. (08/2006)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| I.S. EN ISO 9445:2006 | Identical |
| UNE-EN ISO 9445:2008 | Identical |
| DIN EN ISO 9445:2006-05 | Identical |
| UNI EN ISO 9445 : 2007 | Identical |
| SN EN ISO 9445 : 2006 | Identical |
| NF EN ISO 9445 : 2006 | Identical |
| ISO 9445:2002 | Identical |
| EN ISO 9445:2006 | Identical |
| NBN EN ISO 9445 : 2006 | Identical |
| NEN EN ISO 9445 : 2006 | Identical |
| NS EN ISO 9445 : 2006 | Identical |
| DEFSTAN 02-121(PT1)/3(2010) : 2010 | REQUIREMENTS FOR GALLEYS AND ASSOCIATED SPACES - PART 1: COMMON REQUIREMENTS |
| DEFSTAN 02-128/2(2008) : 2008 | FURNITURE AND ASSOCIATED EQUIPMENT REQUIREMENTS FOR HM SHIPS |
| DEFSTAN 02-900(PT0)/3(2014) : 2014 | GENERAL NAVAL STANDARD - PART 0: MANAGEMENT INFORMATION, COMMON DATA AND PROCEDURES FOR USE |
| DEFSTAN 02-320/3(2009) : 2009 | REQUIREMENTS FOR THE DESIGN AND INSTALLATION OF FUEL SYSTEMS FOR GAS TURBINE ENGINES AND DIESEL ENGINES IN HM SURFACE SHIPS AND SUBMARINES |
| DEFSTAN 02-329/3(2010) : 2010 | REQUIREMENTS FOR HEAT EXCHANGERS FOR HM SURFACE SHIPS AND SUBMARINES |
| DEFSTAN 02-900(PT3)/2(2013) : 2013 | GENERAL NAVAL STANDARD - PART 3: SHIP SYSTEMS |
| DEFSTAN 02-900(PT3)/1(2013) : 2013 | GENERAL NAVAL STANDARD - PART 3: SHIP SYSTEMS |
| ISO 6929:2013 | Steel products — Vocabulary |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.