BS EN ISO 4613-2:1995
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics. Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials Preparation of test specimens and determination of properties
Hardcopy , PDF
10-05-2019
English
11-10-2004
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
1 Scope
2 Normative references
3 Preparation of test specimens
4 Conditioning of test specimens
5 Determination of properties
This part of BS EN ISO 4613 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of E/VAC moulding and extrusion materials.
| Committee |
PRI/82
|
| DevelopmentNote |
Supersedes 94/340141 DC (09/2004)
|
| DocumentType |
Standard
|
| Pages |
10
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NF EN ISO 4613-2 : 1995 AMD 1 2004 | Identical |
| NBN EN ISO 4613-2 : 1995 AMD 1 2004 | Identical |
| DIN EN ISO 4613-2:2004-12 | Identical |
| ISO 4613-2:1995 | Identical |
| I.S. EN ISO 4613-2:1996 | Identical |
| SN EN ISO 4613-2 : 1996 AMD 1 2004 | Identical |
| NEN EN ISO 4613-2 : 1995 AMD 1 2004 | Identical |
| NS EN ISO 4613-2 : 1995 AMD 1 2004 | Identical |
| UNI EN ISO 4613-2 : 2007 | Identical |
| UNE-EN ISO 4613-2:1996 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 75-1:2013 | Plastics Determination of temperature of deflection under load Part 1: General test method |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 3167:2014 | Plastics Multipurpose test specimens |
| ISO 527-4:1997 | Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| ISO 8985:1998 | Plastics Ethylene/vinyl acetate copolymer (EVAC) thermoplastics Determination of vinyl acetate content |
| ISO 4613-1:1993 | Plastics Ethylene/vinyl acetate (E/VAC) moulding and extrusion materials Part 1: Designation and specification |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| ISO 10350:1993 | Plastics Acquisition and presentation of comparable single-point data |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| ISO 1628-3:2010 | Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 3: Polyethylenes and polypropylenes |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| ISO 1183:1987 | Plastics Methods for determining the density and relative density of non-cellular plastics |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 1210:1992 | Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source |
| ISO 3146:2000 | Plastics — Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods |
| ISO 62:2008 | Plastics Determination of water absorption |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 179:1993 | Plastics Determination of Charpy impact strength |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| ISO 178:2010 | Plastics Determination of flexural properties |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.