BS EN ISO 3506-1:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Mechanical properties of corrosion-resistant stainless steel fasteners Bolts, screws and studs
Hardcopy , PDF
20-04-2020
English
31-12-2009
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Symbols
4 Designation, marking and finish
5 Chemical composition
6 Mechanical properties
7 Testing
Annex A (normative) - External thread - Calculation of
stress area
Annex B (informative) - Description of the groups and
grades of stainless steels
Annex C (informative) - Stainless steel composition
specifications
Annex D (informative) - Stainless steels for cold
heading and extruding
Annex E (informative) - Austenitic stainless steels
with particular resistance to
chloride induced stress
corrosion
Annex F (informative) - Mechanical properties at
elevated temperatures;
application at low
temperatures
Annex G (informative) - Time-temperature diagram of
intergranular corrosion in
austenitic stainless steels,
grade A2 (18/8 steels)
Annex H (informative) - Magnetic properties for
austenitic stainless steels
Bibliography
Describes the mechanical properties of bolts, screws and studs made of austenitic, martensitic and ferritic steel grades of corrosion-resistant stainless steels, when tested over an ambient temperature range of 10 degree C to 35 degree C.
| Committee |
FME/9
|
| DevelopmentNote |
Supersedes 95/710057 DC. Together with BS EN ISO 3506-2 supersedes BS 6105(1981). (10/2005) Supersedes 08/30165724 DC. (12/2009)
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| EN ISO 3506-1:2009 | Identical |
| NS EN ISO 3506-1 : 2009 | Identical |
| NBN EN ISO 3506-1 : 2010 | Identical |
| UNI EN ISO 3506-1 : 2010 | Identical |
| NF EN ISO 3506-1 : 2010 | Identical |
| UNE-EN ISO 3506-1:2010 | Identical |
| DIN EN ISO 3506-1:2010-04 | Identical |
| I.S. EN ISO 3506-1:2009 | Identical |
| SN EN ISO 3506-1 : 2010 | Identical |
| ISO 3506-1:2009 | Identical |
| NEN EN ISO 3506-1 : 2009 | Identical |
| ONORM EN ISO 3506-1 : 2010 | Identical |
| 15/30095322 DC : 0 | BS 5427 - CODE OF PRACTICE FOR THE USE OF PROFILED SHEET FOR ROOF AND WALL CLADDING ON BUILDINGS |
| DEFSTAN 02-862(PT1)/2(2007) : 2007 | FASTENERS - PART 1: GENERAL |
| BS 8561:2013 | Specification for mechanical fittings for use in the repair, connection and renovation of pressurized water supply pipelines. Requirements and test methods |
| BS 8297:2000 | Code of practice for Design and installation of non-loadbearing precast concrete cladding |
| BS 8297:2017 | Design, manufacture and installation of architectural precast concrete cladding. Code of practice |
| BS 4873:2004 | Aluminium alloy windows |
| 09/30196573 DC : 0 | BS 8530 - TRADITIONAL-STYLE HALF ROUND, BEADED HALF ROUND, VICTORIAN OGEE AND MOULDED OGEE ALUMINIUM RAINWATER SYSTEMS - SPECIFICATION |
| BS 8298-2:2010 | Code of practice for the design and installation of natural stone cladding and lining Traditional handset external cladding |
| DEFSTAN 02-862(PT3)/3(2011) : 2011 | NAVAL FASTENERS - PART 3: PROCUREMENT OF FIRST LEVEL FASTENERS |
| BS 5427(2016) : 2016 | CODE OF PRACTICE FOR THE USE OF PROFILED SHEET FOR ROOF AND WALL CLADDING ON BUILDINGS |
| 17/30342957 DC : 0 | BS 8297 - DESIGN, MANUFACTURE AND INSTALLATION OF ARCHITECTURAL PRECAST CONCRETE CLADDING - CODE OF PRACTICE |
| DEFSTAN 07-281/2(2017) : 2017 | SPECIFICATION FOR THE TYPE X RESILIENT MOUNT AND THE LEAF SPRING ASSEMBLY OF THE TYPE Y RESILIENT MOUNT |
| BS 8539:2012 | Code of practice for the selection and installation of post-installed anchors in concrete and masonry |
| 11/30237359 DC : 0 | BS 8561 - MECHANICAL FITTINGS FOR USE IN THE REPAIR, CONNECTION AND RENOVATION OF PRESSURIZED WATER SUPPLY PIPELINES - SPECIFICATION |
| 12/30270677 DC : 0 | BS 8561 - RENOVATION AND CONNECTION FITTINGS FOR USE ON WATER SUPPLY PIPES |
| 13/30102062 DC : 0 | BS 7608:2013 - GUIDE TO FATIGUE DESIGN AND ASSESSMENT OF STEEL PRODUCTS |
| BS 6779-4:1999 | Highway parapets for bridges and other structures Specification for parapets of reinforced and unreinforced masonry construction |
| 12/30215639 DC : 0 | BS 8539 - CODE OF PRACTICE FOR THE SELECTION AND INSTALLATION OF POST-INSTALLED ANCHORS IN CONCRETE AND MASONRY |
| DEFSTAN 02-862(PT2)/3(2011) : 2011 | NAVAL FASTENERS - PART 2: PROCUREMENT OF NON-FIRST LEVEL FASTENERS |
| BS 8221-2:2000 | Code of practice for cleaning and surface repair of buildings Surface repair of natural stones, brick and terracotta |
| BS 8530:2010 | Traditional-style half round, beaded half round, Victorian ogee and moulded ogee aluminium rainwater systems. Specification |
| DEFSTAN 02-862(PT1)/3(2011) : 2011 | NAVAL FASTENERS - PART 1: MATERIAL SELECTION AND USE |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| ISO 6506-1:2014 | Metallic materials Brinell hardness test Part 1: Test method |
| ISO 683-13:1974 | Heat-treated steels, alloy steels and free-cutting steels Part 13: Wrought stainless steels |
| ISO 6508-1:2016 | Metallic materials — Rockwell hardness test — Part 1: Test method |
| ISO 724:1993 | ISO general-purpose metric screw threads — Basic dimensions |
| ISO 16426:2002 | Fasteners — Quality assurance system |
| ISO 6892-1:2016 | Metallic materials Tensile testing Part 1: Method of test at room temperature |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| ISO 68-1:1998 | ISO general purpose screw threads — Basic profile — Part 1: Metric screw threads |
| ISO 3651-2:1998 | Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid |
| ISO 8044:2015 | Corrosion of metals and alloys Basic terms and definitions |
| ISO 16048:2003 | Passivation of corrosion-resistant stainless-steel fasteners |
| ISO 3651-1:1998 | Determination of resistance to intergranular corrosion of stainless steels — Part 1: Austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in nitric acid medium by measurement of loss in mass (Huey test) |
| ISO 261:1998 | ISO general purpose metric screw threads — General plan |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 4954:1993 | Steels for cold heading and cold extruding |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.