BS EN ISO 3269:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Fasteners. Acceptance inspection
Hardcopy , PDF
15-10-2019
English
15-07-2001
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and conditions
4 General principles and requirements
5 Acceptance inspection procedure for fastener
characteristics
Annex A (informative) Recommendations for acceptance-
inspection procedures (for example, for dimensional
characteristics)
Annex B (informative) Guidance and explanation
concerning the principle of this international
standard
Bibliography
Gives the procedure to be followed by the purchaser at his acceptance inspection so as to decide whether a lot of fasteners may be accepted or rejected, when another acceptance procedure has not been agreed.
| Committee |
FME/9
|
| DevelopmentNote |
Supersedes 97/713351 DC (06/2005) Reviewed and confirmed by BSI, January 2007. (12/2006)
|
| DocumentType |
Standard
|
| Pages |
30
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 3269:2000 | Identical |
| ONORM EN ISO 3269 : 2000 | Identical |
| NEN EN ISO 3269 : 2000 | Identical |
| NS EN ISO 3269 : 1ED 2000 | Identical |
| EN ISO 3269:2000 | Identical |
| NF EN ISO 3269 : 2000 | Identical |
| UNI EN ISO 3269 : 2002 | Identical |
| SN EN ISO 3269 : 2000 | Identical |
| NBN EN ISO 3269 : 2000 | Identical |
| DIN EN ISO 3269:2000-11 | Identical |
| I.S. EN ISO 3269:2000 | Identical |
| BS 4933:2010 | Specification for ISO metric black cup and countersunk head bolts and screws with hexagon nuts |
| BS 7419:2012 | Specification for holding down bolts |
| 12/30258706 DC : 0 | BS 7419 - SPECIFICATION FOR HOLDING DOWN BOLTS |
| ISO 8839:1986 | Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metals |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| ISO 10683:2014 | Fasteners Non-electrolytically applied zinc flake coatings |
| EN 26157-3:1991 | Fasteners - Surface discontinuities - Part 3: Bolts, screws and studs for special requirements (ISO 6157-3:1988) |
| ISO 4759-3:2016 | Tolerances for fasteners Part 3: Washers for bolts, screws and nuts Product grades A, C and F |
| ISO 4042:1999 | Fasteners Electroplated coatings |
| ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 1: Bolts, screws and studs |
| ISO 6157-3:1988 | Fasteners — Surface discontinuities — Part 3: Bolts, screws and studs for special requirements |
| EN ISO 4042:1999 | Fasteners - Electroplated coatings (ISO 4042:1999) |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| EN ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:2009) |
| ISO 4759-1:2000 | Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B and C |
| ISO 6157-1:1988 | Fasteners — Surface discontinuities — Part 1: Bolts, screws and studs for general requirements |
| EN 26157-1:1991 | Fasteners - Surface discontinuities - Part 1: Bolts, screws and studs for general requirements (ISO 6157-1:1988) |
| ISO 2320:2015 | Fasteners Prevailing torque steel nuts Functional properties |
| EN ISO 4759-3:2016 | Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F (ISO 4759-3:2016) |
| ISO 7085:1999 | Mechanical and performance requirements of case hardened and tempered metric thread rolling screws |
| ISO 8402:1994 | Quality management and quality assurance — Vocabulary |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| ISO 1502:1996 | ISO general-purpose metric screw threads Gauges and gauging |
| ISO 898-6:1994 | Mechanical properties of fasteners Part 6: Nuts with specified proof load values Fine pitch thread |
| ISO 898-5:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel Part 5: Set screws and similar threaded fasteners with specified hardness classes Coarse thread and fine pitch thread |
| ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 3: Set screws and similar fasteners not under tensile stress |
| EN ISO 2702:2011 | Heat-treated steel tapping screws - Mechanical properties (ISO 2702:2011) |
| ISO 3534-2:2006 | Statistics — Vocabulary and symbols — Part 2: Applied statistics |
| EN ISO 898-5:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread (ISO 898-5:2012) |
| EN ISO 2320:2015 | Fasteners - Prevailing torque steel nuts - Functional properties (ISO 2320:2015) |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| ISO 6157-2:1995 | Fasteners Surface discontinuities Part 2: Nuts |
| EN ISO 898-6:1995 | Mechanical properties of fasteners - Part 6: Nuts with specified proof load values - Fine pitch thread (ISO 898-6:1994) |
| ISO 8992:2005 | Fasteners — General requirements for bolts, screws, studs and nuts |
| ISO 2702:2011 | Heat-treated steel tapping screws — Mechanical properties |
| ISO 1478:1999 | Tapping screws thread |
| EN ISO 1478:1999 | Tapping screws thread (ISO 1478:1999) |
| ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners Part 2: Nuts |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
| EN ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.