BS EN 62282-3-2:2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Fuel cell technologies Stationary fuel cell power systems. Performance test methods
Hardcopy , PDF
31-01-2012
English
31-07-2006
Important note : All end users must be registered with an Account prior to user licenses being assigned.
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms, definitions and symbols
3.1 Terms and definitions
3.2 Symbols
4 Reference conditions
4.1 General
4.2 Temperature and pressure
4.3 Heating value base
5 Performance and classes of tests
5.1 Performance tests
5.2 Classes of tests
6 Test preparation
6.1 General
6.2 Uncertainty analysis
6.2.1 Uncertainty analysis items
6.2.2 Data acquisition plan
7 Instruments and measurement methods
7.1 General
7.2 Instruments
7.3 Measurement methods
7.3.1 Electrical power
7.3.2 Fuel consumption
7.3.3 Liquid fuel measurements
7.3.4 Recovered heat
7.3.5 Purge gas flow
7.3.6 Oxidant (air) characteristics
7.3.7 Other fluid flow
7.3.8 Exhaust gas emission measurement
7.3.9 Discharge water quality measurement
7.3.10 pH (Hydrogen ion concentration)
7.3.11 COD (Chemical Oxygen Demand)
7.3.12 BOD (Biochemical Oxygen Demand)
7.3.13 Audible noise level
7.3.14 Vibration level
7.3.15 Total harmonic distortion
7.3.16 Ambient conditions
8 Test method and computation of results
8.1 Test plan
8.1.1 General
8.1.2 Ambient conditions
8.1.3 Maximum permissible variation in steady-state
operating conditions
8.1.4 Test operating procedure
8.2 Duration of test and frequency of readings
8.3 Computation of results
8.3.1 Electrical power
8.3.2 Fuel consumption
8.3.3 Calculation of fuel energy
8.3.4 Oxidant (air) consumption
8.3.5 Calculation of oxidant (air) energy
8.3.6 Electrical efficiency
8.3.7 Heat recovery efficiency
8.3.8 Overall energy efficiency
8.3.9 Power and thermal response characteristics
8.3.10 Start-up and shutdown characteristics
8.3.11 Purge gas consumption
8.3.12 Water consumption
8.3.13 Waste heat
8.3.14 Exhaust gas emission
8.3.15 Calculation of emission production
8.3.16 Audible noise level
8.3.17 Vibration level
8.3.18 Discharge water quality
9 Test reports
9.1 General
9.2 Title page
9.3 Table of contents
9.4 Summary report
9.5 Detailed report
9.6 Full report
Annex A (normative) Guidance for uncertainty analysis
Annex B (normative) Calculation of fuel heating value
Annex C (normative) Reference gas
Annex ZA (normative) Normative references to international
publications with their corresponding European
publications
Bibliography
Specifies operational and environmental aspects of the stationary fuel cell power systems performance.
| Committee |
GEL/105
|
| DevelopmentNote |
Supersedes 02/203214 DC (08/2006)
|
| DocumentType |
Standard
|
| Pages |
82
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
Covers operational and environmental aspects of the stationary fuel cell power systems performance. The test methods apply to power output under specified operating and transient conditions; electrical and thermal efficiency under specified operating conditions; environmental characteristics under specified operating and transient conditions.
| Standards | Relationship |
| DIN EN 62282-3-2 : 2007 | Identical |
| IEC 62282-3-2:2006 | Identical |
| SN EN 62282-3-2 : 2006 | Identical |
| I.S. EN 62282-3-2:2006 | Identical |
| NBN EN 62282-3-2 : 2007 | Identical |
| UNE-EN 62282-3-2:2007 | Identical |
| EN 62282-3-2:2006 | Identical |
| EN 60688:2013 | Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals |
| IEC 61672-2:2013+AMD1:2017 CSV | Electroacoustics - Sound level meters - Part 2: Pattern evaluation tests |
| EN ISO 11541:2002 | Natural gas - Determination of water content at high pressure (ISO 11541:1997) |
| ISO 3648:1994 | Aviation fuels — Estimation of net specific energy |
| ISO 3744:2010 | Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane |
| ISO 6976:2016 | Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition |
| EN 60359:2002 | Electrical and electronic measurement equipment - Expression of performance |
| EN 61672-2:2013/A1:2017 | ELECTROACOUSTICS - SOUND LEVEL METERS - PART 2: PATTERN EVALUATION TESTS (IEC 61672-2:2013/A1:2017) |
| IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
| IEC 60688:2012 | Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals |
| EN 61000-4-7:2002/A1:2009 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-7: TESTING AND MEASUREMENT TECHNIQUES - GENERAL GUIDE ON HARMONICS AND INTERHARMONICS MEASUREMENTS AND INSTRUMENTATION, FOR POWER SUPPLY SYSTEMS AND EQUIPMENT CONNECTED THERETO (IEC 61000-4-7:2002/A1:2008) |
| ISO 6975:1997 | Natural gas — Extended analysis — Gas-chromatographic method |
| ISO 7935:1992 | Stationary source emissions — Determination of the mass concentration of sulfur dioxide — Performance characteristics of automated measuring methods |
| IEC 62052-11:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - General requirements, tests and test conditions - Part 11: Metering equipment |
| ISO 8217:2017 | Petroleum products — Fuels (class F) — Specifications of marine fuels |
| ISO 6060:1989 | Water quality — Determination of the chemical oxygen demand |
| ISO 4677-1:1985 | Atmospheres for conditioning and testing Determination of relative humidity Part 1: Aspirated psychrometer method |
| ISO 16622:2002 | Meteorology — Sonic anemometers/thermometers — Acceptance test methods for mean wind measurements |
| ISO 11042-1:1996 | Gas turbines — Exhaust gas emission — Part 1: Measurement and evaluation |
| ISO 11042-2:1996 | Gas turbines — Exhaust gas emission — Part 2: Automated emission monitoring |
| EN 61672-1:2013 | Electroacoustics - Sound level meters - Part 1: Specifications |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| ISO 8041:2005 | Human response to vibration Measuring instrumentation |
| EN ISO 10707:1997 | Water quality - Evaluation in an aqueous medium of the "ultimate" aerobic biodegradability of organic compounds - Method by analysis of biochemical oxygen demand (closed bottle test) (ISO 10707:1994) |
| ISO 11541:1997 | Natural gas Determination of water content at high pressure |
| EN ISO 6975:2005 | Natural gas - Extended analysis - Gas-chromatographic method (ISO 6975:1997) |
| IEC 61000-4-7:2002+AMD1:2008 CSV | Electromagnetic compatibility (EMC) - Part 4-7: Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto |
| IEC 62053-22:2003+AMD1:2016 CSV | Electricity metering equipment (a.c.) - Particular Requirements - Part 22: Static meters for active energy (classes 0,2 S and 0,5 S) |
| IEC 60359:2001 | Electrical and electronic measurement equipment - Expression of performance |
| ISO 10707:1994 | Water quality Evaluation in an aqueous medium of the "ultimate" aerobic biodegradability of organic compounds Method by analysis of biochemical oxygen demand (closed bottle test) |
| ISO 5348:1998 | Mechanical vibration and shock Mechanical mounting of accelerometers |
| ISO 10849:1996 | Stationary source emissions — Determination of the mass concentration of nitrogen oxides — Performance characteristics of automated measuring systems |
| ISO 10780:1994 | Stationary source emissions — Measurement of velocity and volume flowrate of gas streams in ducts |
| EN 61028:1993/A2:1997 | ELECTRICAL MEASURING INSTRUMENTS - X-Y RECORDERS |
| EN ISO 6976:2016 | Natural gas - Calculation of calorific values, density, relative density and Wobbe indices from composition (ISO 6976:2016) |
| ISO 10523:2008 | Water quality — Determination of pH |
| ISO 10396:2007 | Stationary source emissions — Sampling for the automated determination of gas emission concentrations for permanently-installed monitoring systems |
| IEC 61028:1990 | Electrical measuring instruments - X-Y recorders |
| ISO 4677-2:1985 | Atmospheres for conditioning and testing Determination of relative humidity Part 2: Whirling psychrometer method |
| EN 61000-4-13:2002/A2:2016 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-13: TESTING AND MEASUREMENT TECHNIQUES - HARMONICS AND INTERHARMONICS INCLUDING MAINS SIGNALLING AT A.C. POWER PORT, LOW FREQUENCY IMMUNITY TESTS (IEC 61000-4-13:2002/A2:2015) |
| IEC 60050-300:2001 | International Electrotechnical Vocabulary (IEV) - Part 300: Electrical and electronic measurements and measuring instruments - Part 311: General terms relating to measurements - Part 312: General terms relating to electrical measurements - Part 313: Types of electrical measuring instruments - Part 314: Specific terms according to the type of instrument |
| IEC 61000-4-13:2002+AMD1:2009+AMD2:2015 CSV | Electromagnetic compatibility (EMC) - Part 4-13: Testing and measurement techniques - Harmonics and interharmonics includingmains signalling at a.c. power port, low frequency immunity tests |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.