BS EN 60297-5-103:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Mechanical structures for electronic equipment. Dimensions of mechanical structures of the 482.6 mm (19 in) series. Subracks and associated plug-in units Electrostatic discharge protection
Hardcopy , PDF
30-05-2008
English
15-08-2001
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Introduction
Clause
1 Scope and object
2 Normative references
3 Definitions
4 Extended feature added to IEC 60297-3 and IEC 60927-4
5 General equipment arrangement
6 Provision for electrostatic discharge protection
6.1 Subrack front and/or rear interface dimensions
for electrostatic discharge protection
6.2 Plug-in unit interface dimensions for
electrostatic discharge protection
Figure 1 - General equipment arrangement - Typical 6U
subrack front and/or rear mounted plug-in units
featured with electrostatic discharge protection
Figure 2 - Subrack guide rail dimensions for the
electrostatic discharge contact position
Figure 3 - Printed board discharge strip dimensions
maintaining ESD contact during connector engagement
Figure 4 - Printed board discharge strip dimensions
breaking ESD contact before connector engagement
Annex ZA (normative) Normative references to international
publications with their corresponding European
publications
Provides the extended features of electrostatic discharge protection added to subracks and plug-in units according to IEC 60297-3, IEC 60297-4 and IEC 60297-5-107.
| Committee |
EPL/48
|
| DevelopmentNote |
Also numbered as IEC 60297-5-103. (06/2001) Supersedes 98/231540 DC. (05/2005)
|
| DocumentType |
Standard
|
| Pages |
14
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
Specifies dimensions which will ensure dimensional interchangeability of subracks and associated plug-in units using the extended function of electrostatic discharge protection added to IEC 60297-3, IEC 60297-4 and IEC 60297-5-107.
| Standards | Relationship |
| UNE-EN 60297-5-103:2001 | Identical |
| SN EN 60297-5-103 : 2001 | Identical |
| I.S. EN 60297-5-103:2001 | Identical |
| DIN EN 60297-5-103:2001-11 | Identical |
| EN 60297-5-103:2001 | Identical |
| EN 60297-5-100:2001 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-100: Subracks and associated plug-in units - Design overview |
| IEC 60297-5-107:2001 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-107: Subracks and associated plug-in units - Rear-mounted plug-in units |
| IEC 61587-1:2016 | Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation |
| IEC 60297-4:1995+AMD1:1999 CSV | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 4: Subracks and associated plug-in units - Additional dimensions |
| EN 60297-5-107:2001 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-107: Subracks and associated plug-in units - Rear mounted plug-in units |
| EN 61587-1:2017 | Mechanical structures for electronic equipment - Tests for IEC 60917 and IEC 60297 series - Part 1: Environmental requirements, test set-up and safety aspects for cabinets, racks, subracks and chassis under indoor condition use and transportation |
| IEC 60297-5-100:2001 | Mechanical structures for electronic equipment - Dimensions of mechanical structures of the 482,6 mm (19 in) series - Part 5-100: Subracks and associated plug-in units - Design overview |
| EN 60297-4:1995/A1:1999 | MECHANICAL STRUCTURES FOR ELECTRONIC EQUIPMENT - DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482.6 MM (19 IN) SERIES - SUBRACKS AND ASSOCIATED PLUG-IN UNITS - ADDITIONAL DIMENSIONS |
| HD 493.3 : 200S2 | DIMENSIONS OF MECHANICAL STRUCTURES OF THE 482.6 MM (19 IN) SERIES - SUBRACKS AND ASSOCIATED PLUG-IN UNITS |
| IEC 60917-1:1998+AMD1:2000 CSV | Modular order for the development of mechanical structures for electronic equipment practices - Part 1: Generic standard |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.