BS EN 13718-1:2014
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Medical vehicles and their equipment. Air ambulances Requirements for medical devices used in air ambulances
Available format(s)
Hardcopy , PDF
Superseded date
10-04-2020
Superseded by
Language(s)
English
Published date
30-09-2014
Publisher
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements for medical devices for air ambulances
5 Test methods
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 93/42/EEC Medical Devices
Bibliography
Describes general requirements for medical devices carried in air ambulances and used therein and outside hospitals and clinics in situations where the ambient conditions can differ from normal indoor conditions.
| Committee |
CH/239
|
| DevelopmentNote |
Supersedes 99/565439 DC (10/2002) Supersedes 06/30106983 DC. (09/2008) Supersedes 13/30276231 DC. (10/2014)
|
| DocumentType |
Standard
|
| Pages |
22
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This European Standard specifies general requirements for medical devices carried in air ambulances and used therein and outside hospitals and clinics in situations where the ambient conditions can differ from normal indoor conditions. This European Standard does not cover the requirements for approval and registration of the vehicle and the training of the staff which is the responsibility of the authority/authorities in the country where the ambulance is to be registered.
| Standards | Relationship |
| UNI EN 13718-1 : 2014 | Identical |
| NS EN 13718-1 : 2014 | Identical |
| NF EN 13718-1 : 2017 | Identical |
| SN EN 13718-1 : 2014 | Identical |
| NBN EN 13718-1 : 2014 | Identical |
| UNE-EN 13718-1:2009 | Identical |
| DIN EN 13718-1:2014-12 | Identical |
| I.S. EN 13718-1:2014 | Identical |
| NEN EN 13718-1 : 2014 | Identical |
| EN 13718-1:2014 | Identical |
| ONORM EN 13718-1 : 2014 | Identical |
| EN ISO 11197:2016 | Medical supply units (ISO 11197:2016) |
| EN ISO 407:2004 | Small medical gas cylinders - Pin-index yoke-type valve connections (ISO 407:2004) |
| MIL-STD-704 Revision F:2004 | AIRCRAFT ELECTRIC POWER CHARACTERISTICS |
| EN 1865-1:2010+A1:2015 | Patient handling equipment used in road ambulances - Part 1: General stretcher systems and patient handling equipment |
| ISO 15002:2008 | Flow-metering devices for connection to terminal units of medical gas pipeline systems |
| ISO 7637-1:2015 | Road vehicles — Electrical disturbances from conduction and coupling — Part 1: Definitions and general considerations |
| MIL-DTL-26482 Revision H:2007 | Connectors, Electrical, Circular, Miniature, Quick Disconnect, Environment Resisting, Receptacles and Plugs, General Specification for |
| MIL-STD-810 Revision G:2008 | ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS |
| IEC 60601-1:2005+AMD1:2012 CSV | Medical electrical equipment - Part 1: General requirements for basic safety and essential performance |
| EN ISO 15002:2008 | Flow-metering devices for connection to terminal units of medical gas pipeline systems (ISO 15002:2008) |
| ISO 10524-4:2008 | Pressure regulators for use with medical gases — Part 4: Low-pressure regulators |
| ISO 7637-2:2011 | Road vehicles Electrical disturbances from conduction and coupling Part 2: Electrical transient conduction along supply lines only |
| IEC 60601-1-6:2010+AMD1:2013 CSV | Medical electrical equipment - Part 1-6: General requirements for basic safety and essential performance - Collateral standard: Usability |
| EN 1005-2:2003+A1:2008 | Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery |
| EN 1865-4:2012 | Patient handling equipment used in road ambulances - Part 4: Foldable patient transfer chair |
| ISO 9170-2:2008 | Terminal units for medical gas pipeline systems — Part 2: Terminal units for anaesthetic gas scavenging systems |
| ISO 19054:2005 | Rail systems for supporting medical equipment |
| EN 60068-2-64:2008 | ENVIRONMENTAL TESTING - PART 2-64: TESTS - TEST FH: VIBRATION, BROADBAND RANDOM AND GUIDANCE |
| EN 1865-2:2010+A1:2015 | Patient handling equipment used in road ambulances - Part 2: Power assisted stretcher |
| IEC 61000-4-4:2012 RLV | Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test |
| EN 60601-1-6:2010/A1:2015 | MEDICAL ELECTRICAL EQUIPMENT - PART 1-6: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE - COLLATERAL STANDARD: USABILITY (IEC 60601-1-6:2010/A1:2013) |
| EN ISO 10524-4:2008 | Pressure regulators for use with medical gases - Part 4: Low-pressure regulators (ISO 10524-4:2008) |
| EN 61000-4-2:2009 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| RTCA DO 199 VOL II : 1988 | Potential Interference to Aircraft Electronic Equipment from Devices Carried Aboard (Vol II) |
| IEC 60068-2-31:2008 | Environmental testing - Part 2-31: Tests - Test Ec: Rough handling shocks, primarily for equipment-type specimens |
| ISO 7396-2:2007 | Medical gas pipeline systems Part 2: Anaesthetic gas scavenging disposal systems |
| IEC 60068-2-64:2008 | Environmental testing - Part 2-64: Tests - Test Fh: Vibration, broadband random and guidance |
| IEC 62366:2007+AMD1:2014 CSV | Medical devices - Application of usability engineering to medical devices |
| IEC 61000-4-6:2013 | Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields |
| EN 61000-4-3 : 2006 AMD 2 2010 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-3: TESTING AND MEASUREMENT TECHNIQUES - RADIATED, RADIO-FREQUENCY, ELECTROMAGNETIC FIELD IMMUNITY TEST |
| ISO 10297:2014 | Gas cylinders — Cylinder valves — Specification and type testing |
| ISO 5359:2014 | Anaesthetic and respiratory equipment — Low-pressure hose assemblies for use with medical gases |
| EN 1041:2008+A1:2013 | Information supplied by the manufacturer of medical devices |
| ISO 10524-3:2005 | Pressure regulators for use with medical gases Part 3: Pressure regulators integrated with cylinder valves |
| ISO 11197:2016 | Medical supply units |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| MIL-STD-461 Revision G:2015 | REQUIREMENTS FOR THE CONTROL OF ELECTROMAGNETIC INTERFERENCE CHARACTERISTICS OF SUBSYSTEMS AND EQUIPMENT |
| EN 13976-2:2011 | Rescue systems - Transportation of incubators - Part 2: System requirements |
| IEC 61000-4-2:2008 | Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test |
| IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV | Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test |
| RTCA DO 199 VOL I : 1988 | Potential Interference to Aircraft Electronic Equipment from Devices Carried Aboard (Vol I) |
| EN 62366 : 2008 AMD 1 2015 | MEDICAL DEVICES - APPLICATION OF USABILITY ENGINEERING TO MEDICAL DEVICES (IEC 62366:2007/A1:2014) |
| EN 1865-3:2012+A1:2015 | Patient handling equipment used in road ambulances - Part 3: Heavy duty stretcher |
| EN ISO 14971:2012 | Medical devices - Application of risk management to medical devices (ISO 14971:2007, Corrected version 2007-10-01) |
| EN 60068-2-29:1993 | Environmental testing - Part 2: Tests - Test Eb and guidance: Bump |
| ISO 407:2004 | Small medical gas cylinders Pin-index yoke-type valve connections |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| EN ISO 9170-2:2008 | Terminal units for medical gas pipeline systems - Part 2: Terminal units for anaesthetic gas scavenging systems (ISO 9170-2:2008) |
| EN 1789:2007+A2:2014 | Medical vehicles and their equipment - Road ambulances |
| EN 61000-4-4:2012 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST (IEC 61000-4-4:2012) |
| CISPR 11:2015 RLV | Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement |
| IEC 60068-2-29:1987 | Environmental testing. Part 2: Tests. Test Eb and guidance: Bump |
| EN ISO 7396-2:2007 | Medical gas pipeline systems - Part 2: Anaesthetic gas scavenging disposal systems (ISO 7396-2:2007) |
| EN 61000-4-6:2014/AC:2015 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS (IEC 61000-4-6:2013) |
| ISO 14971:2007 | Medical devices Application of risk management to medical devices |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| EN ISO 10524-2:2006 | Pressure regulators for use with medical gases - Part 2: Manifold and line pressure regulators (ISO 10524-2:2005) |
| EN 13976-1:2011 | Rescue systems - Transportation of incubators - Part 1: Interface conditions |
| EN ISO 10524-1:2006 | Pressure regulators for use with medical gases - Part 1: Pressure regulators and pressure regulators with flow-metering devices (ISO 10524-1:2006) |
| ISO 10524-1:2006 | Pressure regulators for use with medical gases Part 1: Pressure regulators and pressure regulators with flow-metering devices |
| IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV | Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements |
| ISO 15223-1:2016 | Medical devices Symbols to be used with medical device labels, labelling and information to be supplied Part 1: General requirements |
| EN 60309-2:1999/A2:2012 | PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 2: DIMENSIONAL INTERCHANGEABILITY REQUIREMENTS FOR PIN AND CONTACT-TUBE ACCESSORIES (IEC 60309-2:1999/A2:2012) |
| IEC 60309-2:1999+AMD1:2005+AMD2:2012 CSV | Plugs, socket-outlets and couplers for industrial purposes - Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories |
| EN 1865-5:2012 | Patient handling equipment used in road ambulances - Part 5: Stretcher support |
| ISO 10524-2:2005 | Pressure regulators for use with medical gases Part 2: Manifold and line pressure regulators |
| EN 60068-2-31:2008 | ENVIRONMENTAL TESTING - PART 2-31: TESTS - TEST EC: ROUGH HANDLING SHOCKS, PRIMARILY FOR EQUIPMENT-TYPE SPECIMENS |
| EN 60309-1:1999/A1:2007/AC:2014 | PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 1: GENERAL REQUIREMENTS (IEC 60309-1:1999/A2:2012) |
| EN 13718-2:2015 | Medical vehicles and their equipment - Air ambulances - Part 2: Operational and technical requirements for air ambulances |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.