BS EN 12415:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Safety of machine tools. Small numerically controlled turning machines and turning centres
Hardcopy , PDF
31-08-2010
English
12-11-2003
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
0 Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or measures
6 Information for use
Annex A (informative) Example of check list for safety
functions
Annex B (normative) Guards on turning machines - Impact
test method
Annex C (informative) Test equipment for impact test and
examples of materials
Annex D (normative) Noise emission measurement
Annex E (informative) Calculation of direct impact energy
Annex ZA (informative) Clauses of this European Standard
addressing essential requirements
or other provisions of EU directives
Bibliography
Specifies the requirements and/or measures to remove the hazards and limit the risks on general purpose numerically controlled turning machines and turning centers which are designed primarily to work cold metal with no access to the work-zone during machining as defined in 3.1 and 3.2 and hereafter referred to as "machines".
| Committee |
MTE/1
|
| DevelopmentNote |
Supersedes 96/706742 DC (11/2003)
|
| DocumentType |
Standard
|
| Pages |
44
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NF EN 12415 : 2001 AMD 1 2003 | Identical |
| NS EN 12415 : 2000 AMD 1 2002 | Identical |
| NBN EN 12415 : 2001 AMD 1 2003 | Identical |
| UNI EN 12415 : 2004 | Identical |
| UNE-EN 12415:2001 | Identical |
| SN EN 12415 : 2001 AMD 1 2002 | Identical |
| NEN EN 12415 : 2000 AMD 1 2002 | Identical |
| EN 12415:2000/A1:2002 | Identical |
| DIN EN 12415:2003-05 | Identical |
| I.S. EN 12415:2000 | Identical |
| DIN EN 12415:2001-03 | Identical |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| EN ISO 11204:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010) |
| EN 894-3:2000+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators |
| EN 418 : 1992 | SAFETY OF MACHINERY - EMERGENCY STOP EQUIPMENT, FUNCTIONAL ASPECTS - PRINCIPLES FOR DESIGN |
| EN 982:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics |
| EN 12840 : 2001 | SAFETY OF MACHINE-TOOLS - MANUALLY CONTROLLED TURNING MACHINES WITH OR WITHOUT AUTOMATIC CONTROL |
| EN 1037:1995+A1:2008 | Safety of machinery - Prevention of unexpected start-up |
| EN 12626 : 1997 | SAFETY OF MACHINERY - LASER PROCESSING MACHINES - SAFETY REQUIREMENTS |
| EN 547-2:1996+A1:2008 | Safety of machinery - Human body measurements - Part 2: Principles for determining the dimensions required for access openings |
| EN 60825-1:2014/AC:2017-06 | SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014) |
| EN 1088:1995+A2:2008 | Safety of machinery - Interlocking devices associated with guards - Principles for design and selection |
| EN 894-2:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays |
| EN 1837:1999+A1:2009 | Safety of machinery - Integral lighting of machines |
| EN 999:1998+A1:2008 | Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body |
| EN 349:1993+A1:2008 | Safety of machinery - Minimum gaps to avoid crushing of parts of the human body |
| EN 547-1:1996+A1:2008 | Safety of machinery - Human body measurements - Part 1: Principles for determining the dimensions required for openings for whole body access into machinery |
| ISO 1219-2:2012 | Fluid power systems and components — Graphical symbols and circuit diagrams — Part 2: Circuit diagrams |
| EN 1550:1997+A1:2008 | Machine-tools safety - Safety requirements for the design and construction of work holding chucks |
| EN 1760-1:1997+A1:2009 | Safety of machinery - Pressure sensitive protective devices - Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors |
| EN 1050 : 1996 | SAFETY OF MACHINERY - PRINCIPLES FOR RISK ASSESSMENT |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| EN 292-1 : 1991 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY |
| EN 574:1996+A1:2008 | Safety of machinery - Two-hand control devices - Functional aspects - Principles for design |
| ISO 447:1984 | Machine tools Direction of operation of controls |
| EN ISO 3746:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) |
| EN ISO 3744:2010 | Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010) |
| EN 953:1997+A1:2009 | Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards |
| EN 12478:2000/AC:2001 | SAFETY OF MACHINE TOOLS - LARGE NUMERICALLY CONTROLLED TURNING MACHINES AND TURNING CENTRES |
| EN 547-3:1996+A1:2008 | Safety of machinery - Human body measurements - Part 3: Anthropometric data |
| ISO 1219-1:2012 | Fluid power systems and components — Graphical symbols and circuit diagrams — Part 1: Graphical symbols for conventional use and data-processing applications |
| ISO 2972:1979 | Numerical control of machines — Symbols |
| ENV 26385 : 1990 | ERGONOMIC PRINCIPLES OF THE DESIGN OF WORK SYSTEMS |
| EN 983:1996+A1:2008 | Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics |
| EN 954-1 : 1996 | SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN |
| EN 292-2 : 91 AMD 1 95 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION |
| EN ISO 4871:2009 | Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) |
| PREN 1005-4 : DRAFT 1998 | SAFETY OF MACHINERY - HUMAN PHYSICAL PERFORMANCE - PART 4: EVALUATION OF WORKING POSTURES IN RELATION TO MACHINERY |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| EN ISO 11688-1:2009 | Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995) |
| EN ISO 9614-1:2009 | Acoustics - Determination of sound power levels of noise sources using sound intensity - Part 1: Measurement at discrete points (ISO 9614-1:1993) |
| EN ISO 11202:2010 | Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) |
| EN 1070 : 1998 | SAFETY OF MACHINERY - TERMINOLOGY |
| ISO 230-5:2000 | Test code for machine tools Part 5: Determination of the noise emission |
| EN 692:2005+A1:2009 | Machine tools - Mechanical presses - Safety |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
| EN 894-1:1997+A1:2008 | Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.