BS 799-3:1981
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Oil burning equipment Automatic and semi-automatic atomizing burners up to 36 litres per hour
Hardcopy , PDF
05-02-2020
English
30-04-1981
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Cooperating organizations
Foreword
Section 1 - General
1 Scope
2 References
3 Definitions
Section 2 - Operation of oil burner
4 Oil feed and cut-off
5 Preparation of oil for burning
6 Ignition
7 Air supply
8 Control system for causing burner shut-down
Section 3 - Materials and components
9 Materials
10 Oil filters
11 Oil pumps
12 Valves
13 Oil pressure gauges
14 Painting and identification
15 Electrical equipment
16 Operating instructions
17 Marking
Publications referred to
Requirements for materials from which all component parts of the oil burning equipment shall be constructed, and deals with such points of component design and plant layout as are fundamental to the proper functioning of such equipment.
| Committee |
RHE/13
|
| DevelopmentNote |
Supersedes 79/76768 DC (10/2005) Reviewed and confirmed by BSI, November 2008. (10/2008)
|
| DocumentType |
Standard
|
| Pages |
12
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
This Part of BS 799 specifies requirements for materials from which all component parts of the oil burning equipment shall be constructed, and also deals with such points of component design and plant layout as are fundamental to the proper functioning of such equipment.
The range of equipment includes:
- automatic and semi-automatic oil burners of the monobloc type as defined in Part 6 of this standard;
- dual fuel gas/oil burners when using fuel oil. NOTE See Appendix A of BS 5885:1980.
The standard is applicable to burners with firing rates up to 36 litres per hour that are suitable for either class C2 or class D fuels (see BS 2869) or both, as stated by the manufacturer.
| BS 799-2:1981 | Specification for oil burning equipment Vaporizing burners |
| BS 5410-2:2013 | Code of practice for oil firing Installations over 45 kW output capacity for space heating, hot water and steam supply services |
| BS 4256-1:1972 | Specification for oil-burning air heaters. Non-domestic, transportable, fan-assisted heaters |
| BS 1740:1965 | Specification for pipe fittings iron and steel (screwed BSP thread). |
| BS 2051-1:1973 | Tube and pipe fittings for engineering purposes Copper and copper alloys capillary and compression tube fittings for engineering purposes |
| BS 5410-3:1976 | Code of practice for oil firing Installations for furnaces, kilns, ovens and other industrial purposes |
| BS 3955:1986 | Specification for electrical controls for household and similar general purposes |
| BS 1710:1984 | Specification for identification of pipelines and services |
| BS 799-6:1979 | Specification for oil burning equipment Safety times and safety, control and monitoring devices for atomizing oil burners of the monobloc type |
| BS 66 & 99:1970 | Specification for cast copper alloy pipe fittings for use with screwed copper tubes |
| ISO 3544:1978 | Atomizing oil burners of the monobloc type — Safety times and safety control and monitoring devices |
| BS 5410-1:1977 | Code of practice for oil firing Installations up to 44 kW output capacity for space heating and hot water supply purposes |
| BS 4876:1984 | Specification for performance requirements for domestic flued oil burning appliances (including test procedures) |
| BS 2871-1:1971 | Specification for copper and copper alloys. Tubes Copper tubes for water, gas and sanitation |
| BS 3602:1962 | Specification for steel pipes and tubes for pressure purposes. Carbon steel high duties. |
| BS 4368-3:1974 | Metallic tube connectors for fluid power and general use Specification for light series couplings (metric) |
| BS 3955-3:1979 | Specification for electrical controls for household and similar general purposes. General and specific requirements |
| BS 4256-3:1972 | Specification for oil-burning air heaters Fixed, flued convector heaters |
| BS 1387:1985 | Specification for screwed and socketed steel tubes and tubulars and for plain end steel tubes suitable for welding or for screwing to BS 21 pipe threads |
| BS 5885(1980) : AMD 5019 | INDUSTRIAL GAS BURNERS, OF INPUT RATING 60 KW AND ABOVE |
| BS 1952(1964) : LATEST | COPPER ALLOY GATE VALVES FOR GENERAL PURPOSES |
| BS 2051(1953) : LATEST | TUBE AND PIPE FITTINGS FOR ENGINEERING PURPOSES |
| BS 2871-2:1972 | Specification for copper and copper alloys. Tubes Tubes for general purposes |
| BS 4256-2:1972 | Specification for oil-burning air heaters Fixed, flued, fan-assisted heaters |
| BS 3212:1991 | Specification for flexible rubber tubing, rubber hose and rubber hose assemblies for use in LPG vapour phase and LPG/air installations |
| BS 1306:1975 | Specification for copper and copper alloy pressure piping systems |
| BS 4368-1:1972 | Compression couplings for tubes Specification for heavy series couplings (metric) |
| ISO 5062:1978 | Atomizing oil burners of the monobloc type — Dimensions for pumps |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.