AWWA C516 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
LARGE-DIAMETER RUBBER-SEATED BUTTERFLY VALVES, SIZES 78 IN. (2,000 MM) AND LARGER
Hardcopy , PDF
17-08-2021
English
01-01-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Foreword
I Introduction
II Special Issues
III Use of This Standard
IV Major Revisions
V Comments
Standard
1 General
2 References
3 Definitions
4 Requirements
5 Verification
6 Delivery
Appendix
A - Installation, Operation, and
Maintenance of Large-Diameter
Butterfly Valves
Gives minimum requirements for rubber-seated butterfly valve assemblies that are 78 in. (2,000 mm) diameter and larger with flanged ends suitable for fresh and reclaimed water having a pH range from 6-12 and a temperature range from 33 DEGREES-125 DEGREES F (0.6 DEGREES-52 DEGREES C) and suitable for a maximum steady-state fluid working pressure of 250 psig (1,724 kPa [gauge]), a maximum steady-state differential pressure of 250 psi (1,724 kPa), and a maximum full-open fluid velocity of 16 ft/sec (4.9 m/sec) based on nominal valve size.
| DocumentType |
Revision
|
| ISBN |
9781625761057
|
| Pages |
44
|
| PublisherName |
American Water Works Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| BS EN 593:2017 | Industrial valves. Metallic butterfly valves for general purposes |
| AWWA M44 : 2016 | DISTRIBUTION VALVES: SELECTION, INSTALLATION, FIELD TESTING, AND MAINTENANCE |
| I.S. EN 593:2017 | INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| AWWA M49 : 2017 | BUTTERFLY VALVES: TORQUE, HEAD LOSS, AND CAVITATION ANALYSIS |
| 16/30339483 DC : 0 | BS EN 593 - INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| PREN 593 : DRAFT 2016 | INDUSTRIAL VALVES - METALLIC BUTTERFLY VALVES FOR GENERAL PURPOSES |
| EN 593:2017 | Industrial valves - Metallic butterfly valves for general purposes |
| AWWA M49 : 2012 | BUTTERFLY VALVES: TORQUE, HEAD LOSS, AND CAVITATION ANALYSIS |
| AWWA C541 : 2016 | HYDRAULIC AND PNEUMATIC CYLINDER AND VANE-TYPE ACTUATORS FOR VALVES AND SLIDE GATES |
| NSF 61 : 2016 | DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS |
| AWWA C207 : 2013 | STEEL PIPE FLANGES FOR WATERWORKS SERVICE, SIZES 4 IN. THROUGH 144 IN. (100 MM THROUGH 3,600 MM) |
| ASTM B 154 : 2016 : REDLINE | Standard Test Method for Mercurous Nitrate Test for Copper Alloys |
| AWWA C550 : 2017 | PROTECTIVE INTERIOR COATINGS FOR VALVES AND HYDRANTS |
| AWS A5.4 : 92(R2000) | STAINLESS STEEL ELECTRODES FOR SHIELDED METAL ARC WELDING, SPECIFICATION FOR |
| ASTM D 1141 : 1998 : EDT 1 | Standard Practice for the Preparation of Substitute Ocean Water |
| ASTM D 1149 : 2016-02 | TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT |
| ASTM A 516/A516M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service |
| AWS A5.5 : 1996 | SPECIFICATION FOR LOW ALLOY STEEL ELECTRODES FOR SHIELDED METAL ARC WELDING |
| AWS A5.1 : 91(R1999) | SPECIFICATION FOR CARBON STEEL ELECTRODES FOR SHIELDED METAL ARC WELDING |
| AWWA C542 : 2016 | ELECTRIC MOTOR ACTUATORS FOR VALVES AND SLIDE GATES |
| ASME B16.1 : 2015 | Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 |
| ASTM B 438 : 2017 : REDLINE | Standard Specification for Bronze-Base Powder Metallurgy (PM) Bearings (Oil-Impregnated) |
| AWS A5.11 : 1990 | NICKEL AND NICKEL ALLOY WELDING ELECTRODES FOR SHIELDED METAL ARC WELDING |
| ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
| AWS D1.1 : 2000 | STRUCTURAL WELDING CODE - STEEL |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| NSF 372 : 2016 | DRINKING WATER SYSTEM COMPONENTS - LEAD CONTENT |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.