ASTM F 714 : 2024
Current
The latest, up-to-date edition.
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
Hardcopy , PDF
English
12-02-2024
Committee |
F 17
|
DocumentType |
Standard
|
Pages |
12
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This specification covers polyethylene (PE) pipe made in three standard outside diameter sizing systems, based on outside diameters of DIPS 3, IPS 4, Metric 90 mm and larger. For smaller sizes refer to Specification D3035. See 5.2.5 for guidelines on special sizes.
1.2The piping is intended for new construction and insertion renewal of old piping systems used for the transport of water, municipal sewage, domestic sewage, industrial process liquids, effluents, slurries, etc., in both pressure and nonpressure systems.
Note 1:The user should consult the manufacturer to ensure that any mechanical or chemical effects to the polyethylene pipe caused by the material being transported will not affect the service life beyond limits acceptable to the user. See PPI TR-19 Chemical Resistance of Thermoplastic Piping Materials for guidance on chemical effects, www.plasticpipe.org
1.3All pipes produced under this specification are pressure-rated. See Appendix X5 for information on pressure rating.
Note 2:References and material descriptions for PE2406, PE3408 and materials having a HDB of 1450 psi have been removed from Specification F714 due to changes in Specification D3350 and PPI TR-3. For removed designations, refer to previous editions of Specification F714, Specification D3350, PPI TR-3 and PPI TR-4. The removal of these materials does not affect pipelines that are in service. See Note 4 and Note 9.
1.4This specification includes criteria for choice of raw material, together with performance requirements and test methods for determining conformance with the requirements.
1.5Quality-control measures are to be taken by manufacturers. See Appendix X4 for general information on quality control.
1.6Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.7The following safety hazards caveat pertains only to the test methods portion, Section 6, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F 2880 : 2021 | Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes <fraction><num>3</num><den>4</den></fraction > in. to 65 in. |
ASTM F 1901 : 2022 | Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems |
ASTM F 3123 : 2022 | Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN) |
ASTM F 3565 : 2023 | Standard Practice for Electrofusion Joining Polyethylene (PE) Pipe and Fittings for Pressure Pipe Service |
ASTM F 3536 : 2022 | Standard Specification for PE and PP Mechanical Fittings for use on NPS 3 or Smaller Cold-water Service Polyethylene (PE) or Crosslinked Polyethylene (PEX) Pipe or Tubing |
ASTM F 2620 : 2020 : REV A : EDT 2 | Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings |
ASTM D 3035 : 2022 | Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter |
ASTM F 2021 : 2017 : R2022 | Standard Guide for Design and Installation of Plastic Siphonic Roof Drainage Systems |
ASTM F 2206 : 2019 | Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE) |
ASTM F 1055 : 2016 : REV A : R2022 | Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and Crosslinked Polyethylene (PEX) Pipe and Tubing |
ASTM F 2649 : 2014 : R2023 | Standard Specification for Corrugated High Density Polyethylene (HDPE) Grease Interceptor Tanks |
ASTM F 1962 : 2022 | Standard Guide for Use of Maxi-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings |
ASTM F 3533/F3533M : 2023 | Standard Guide for Inspection and Acceptance of Installed Thermoplastic Storm and Sanitary Sewer Pipe |
ASTM F 2737 : 2011 : R2021 | Standard Specification for Corrugated High Density Polyethylene (HDPE) Water Quality Units |
ASTM F 412 : 2023 | Standard Terminology Relating to Plastic Piping Systems |
ASTM F 1545 : 2015 : REV A : R2021 | Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges |
ASTM F 1759 : 1997 : R2018 | Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications |
ASTM F 645 : 2018 : REV B | Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems |
ASTM F 2165 : 2019 | Standard Specification for Flexible Pre-Insulated Plastic Piping |
ASTM F 3508 : 2021 : REV A | Standard Guide for In-Situ Pipeline Renovation As Dual-Wall Composite Pipeline by Push/Pull Installation of Compressed-Fit Shape-Memory-Polymer Tubular (SMPT) |
ASTM F 412 : 2024 | Standard Terminology Relating to Plastic Piping Systems |
ASTM D 3350 : 2024 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM F 412 : 2024 : REV A | Standard Terminology Relating to Plastic Piping Systems |
ASTM D 3350 : 2021 | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
ASTM D 1599 : 2018 : R2024 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 1599 : 2018 | Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings |
ASTM D 2837 : 2022 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
ASTM D 2837 : 2024 | Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.