ASTM F 36 : 2015 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Compressibility and Recovery of Gasket Materials
15-02-2015
English
01-01-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 09.02, 2015 Defines determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
| Committee |
F 03
|
| DocumentType |
Redline
|
| Pages |
4
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
1.1This test method covers determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets. It is not intended as a test for compressibility under prolonged stress application, generally referred to as “creep,” or for recovery following such prolonged stress application, the inverse of which is generally referred to as “compression set.” Also, it is not intended for tests at other than room temperature. A resiliency characteristic (the amount recovered expressed as a percentage of the compressed thickness) may also be calculated from the test data where desired.
1.2The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| MIL-DTL-24696 Revision C:2008 | GASKET, SHEET, NON-ASBESTOS |
| 14/30304657 DC : 0 | BS ISO 4708 - COMPOSITION CORK - GASKET MATERIAL - TEST METHODS |
| BS ISO 4708:2017 | Composition cork. Gasket material. Test methods |
| BS EN 14772:2005 | Flanges and their joints. Quality assurance inspection and testing of gaskets in accordance with the series of standards EN 1514 and EN 12560 |
| DIN 65221:1989-11 | AEROSPACE; SHEETS FROM RUBBER-CORK; TECHNICAL SPECIFICATION |
| MIL G 16356 : D | GAGE, BOILER WATER, DIRECT READING |
| I.S. EN 14772:2005 | FLANGES AND THEIR JOINTS - QUALITY ASSURANCE INSPECTION AND TESTING OF GASKETS IN ACCORDANCE WITH THE SERIES OF STANDARDS EN 1514 AND EN 12560 |
| EN 14772:2005 | Flanges and their joints - Quality assurance inspection and testing of gaskets in accordance with the series of standards EN 1514 and EN 12560 |
| DIN 3535-5:1993-12 | SEALANTS FOR GAS SUPPLY; SEALING MATERIALS OF RUBBER, CORK AND SYNTHETIC FIBRES FOR GAS ARMATURES AND GAS APPLIANCES; SAFETY REQUIREMENTS, TESTS |
| 03/114555 DC : DRAFT SEP 2003 | EN 14772 - FLANGES AND THEIR JOINTS - QUALITY ASSURANCE INSPECTION AND TESTING OF GASKETS IN ACCORDANCE WITH THE SERIES OF STANDARDS EN 1514 AND EN 12560 |
| MIL-G-24717 Base Document:1989 | GASKET, SHEET, REFRIGERATION, NON-ASBESTOS |
| MIL G 24696 : B | GASKET, SHEET, NON-ASBESTOS |
| ASTM F 146 : 2012 : REDLINE | TEST METHODS FOR FLUID RESISTANCE OF GASKET MATERIALS |
| ISO 4708:2017 | Composition cork — Gasket material — Test methods |
| BS 1832:1991 | Specification for compressed asbestos fibre jointing |
| MIL-G-12803 Revision C:1989 | GASKET MATERIAL, NON-METALLIC |
| HH-M-351 Revision E:1976 | MILLBOARD, ASBESTOS |
| HH-P-46 Revision E:1975 | PACKING; ASBESTOS, SHEET, COMPRESSED |
| SAE AMS 3250 : 2014 | SYNTHETIC RUBBER AND CORK COMPOSITION, GENERAL PURPOSE, SOFT |
| SAE AMS 3251 : 2014 | SYNTHETIC RUBBER AND CORK COMPOSITION, GENERAL PURPOSE, MEDIUM |
| SAE AMS 3843 : 2014 | POLYTETRAFLUOROETHYLENE SHEET, ASBESTOS FIBER REINFORCED, HIGH COMPRESSIBILITY, LOW DENSITY |
| 12/30257022 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - GENERAL REQUIREMENTS |
| MS53063 Revision B:2011 | INDICATOR, AIR CLEANER, INTAKE, RESTRICTION MECHANICAL TYPE |
| DIN 3754-1:1984-05 | GASKET MATERIALS - COMPRESSED ASBESTOS FIBRE SHEETS - DIMENSIONS, REQUIREMENTS, TESTING |
| MIL-A-7021 Revision C:1974 | ASBESTOS SHEET, COMPRESSED, FOR FUEL, LUBRICANT, COOLANT, WATER AND HIGH TEMPERATURE RESISTANT GASKETS |
| MIL G 18498 : C | GLASS SET, WATER GAGE, FLAT, PLAIN. HIGH PRESSURE STEAM (GLASS, MICA SHIELD, SPACERS, & GASKETS) |
| ASTM F 104 : 2011 : REDLINE | Standard Classification System for Nonmetallic Gasket Materials |
| DIN EN 14772:2005-04 | Flanges and their joints - Quality assurance inspection and testing of gaskets in accordance with the series of standards EN 1514 and EN 12560 |
| ASTM D 3297 : 1993 | Practice for Molding and Machining Tolerances for PTFE Resin Parts (Withdrawn 1997) |
| ASTM F 104 : 2011 : REDLINE | Standard Classification System for Nonmetallic Gasket Materials |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.