ASTM F 2818:2010
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Specification for Crosslinked Polyethylene (PEX) Material Gas Pressure Pipe and Tubing
Hardcopy , PDF
11-11-2014
English
01-03-2010
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 08.04, 2017 Defines requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and impact resistance of PEX pipe and tubing for use in fuel gas mains and services for direct burial applications.
| Committee |
F 17
|
| DocumentType |
Standard
|
| Pages |
7
|
| ProductNote |
Reconfirmed 2010
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This specification covers requirements and test methods for material dimensions and tolerances, hydrostatic burst strength, chemical resistance, and impact resistance of PEX pipe and tubing for use in fuel gas mains and services for direct burial applications.
1.2 The text of this specification references notes and footnotes provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM F 412 : 2019 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 543 : 2014 : REDLINE | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
| ASME B31.8 : 2016 | Gas Transmission and Distribution Piping Systems |
| PPI TR 3 : 2017 | POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE |
| ASTM D 792 : 2013 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement |
| ASTM D 2513 : 2017-01 | SPECIFICATION FOR POLYETHYLENE (PE) GAS PRESSURE PIPE, TUBING, AND FITTINGS |
| ASTM D 2765 : 2016 : REDLINE | Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics |
| ASTM D 2122 : 2016 : REDLINE | Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings |
| ASTM D 2290 : 2016-12 | TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE |
| ASTM D 3350 : 2014 : REDLINE | Standard Specification for Polyethylene Plastics Pipe and Fittings Materials |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.