ASTM F 1836M : 2015 : R2019
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Stuffing Tubes, Nylon, and Packing Assemblies (Metric)
Hardcopy , PDF
29-12-2023
English
10-06-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.This specification covers the general requirements for nylon stuffing tubes and packing assemblies.
| Committee |
F 25
|
| DocumentType |
Standard
|
| Pages |
6
|
| ProductNote |
THIS STANDARD ALSO REFERS -IEC Standard 68-2-6
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the general requirements for nylon stuffing tubes and packing assemblies. Nylon stuffing tubes are intended for making electric cable penetrations in marine shipboard enclosures for electrical equipment. The following types are suitable for both thin-wall enclosures up to 5 mm (3/16in.) thick and thick-wall enclosures, bulkheads, and decks of 5 to 19 mm (3/16to 3/4in.) thick.
1.2This specification does not cover metal stuffing tubes.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 2000 : 2003 : REV A : EDT 1 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2001 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 4066 : 2000 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 4066 : 2001 : REV A : R2008 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) (Withdrawn 2012) |
| ASTM D 2000 : 2000 : EDT 1 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2003 : REV A | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 4066 : 2001 : REV A | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 4066 : 2013 : R2019 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 4066 : 2001 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 2000 : 2008 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2006 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2006 : REV A | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 4066 : 1994 : REV B | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 2000 : 2005 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 2000 : 2018 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2006 : REV A : EDT 1 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2012 : R2017 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 4066 : 2000 : REV A | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 2000 : 2004 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 4066 : 1996 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 2000 : 2012 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2003 | Standard Classification System for Rubber Products in Automotive Applications |
| ASTM D 2000 : 2000 | Standard Classification System for Rubber Products in Automotive Applications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.