ASTM F 1314 : 2018
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Wrought Nitrogen Strengthened 22 Chromium–13 Nickel–5 Manganese–2.5 Molybdenum Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S20910)
Hardcopy , PDF
20-05-2024
English
07-03-2018
Important note : All end users must be registered with an Account prior to user licenses being assigned.1.1 This specification covers the chemical, mechanical, and metallurgical requirements for wrought nitrogen strengthened 22 chromium – 13 nickel – 5 manganese – 2.5 molybdenum stainless steel alloy bar and wire for surgical implants.
| Committee |
F 04
|
| DocumentType |
Standard
|
| Pages |
5
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This specification covers the chemical, mechanical, and metallurgical requirements for wrought nitrogen strengthened 22 chromium – 13 nickel – 5 manganese – 2.5 molybdenum stainless steel alloy bar and wire for surgical implants.
1.2The SI units in this standard are the primary units. The values stated in either primary SI units or secondary inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of each other. Combining values form the two systems may result in non-conformance with the standard.
1.3This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM F 2229 : 2012 | Standard Specification for Wrought, Nitrogen Strengthened 23Manganese-21Chromium-1Molybdenum Low-Nickel Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S29108) |
| ASTM F 621 : 2012 : R2017 | Standard Specification for Stainless Steel Forgings for Surgical Implants |
| ASTM F 2581 : 2012 : R2017 | Standard Specification for Wrought Nitrogen Strengthened 11Manganese-17Chromium-3Molybdenum Low-Nickel Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S29225) |
| ASTM F 2180 : 2017 | Standard Specification for Metallic Implantable Strands and Cables |
| ASTM F 2181 : 2014 | Standard Specification for Wrought Seamless Stainless Steel Tubing for Surgical Implants |
| ASTM F 384 : 2017 | Standard Specifications and Test Methods for Metallic Angled Orthopedic Fracture Fixation Devices |
| ASTM F 543 : 2017 | Standard Specification and Test Methods for Metallic Medical Bone Screws |
| ASTM F 2193 : 2018 : REV A | Standard Specifications and Test Methods for Components Used in the Surgical Fixation of the Spinal Skeletal System |
| ASTM F 543 : 2023 | Standard Specification and Test Methods for Metallic Medical Bone Screws |
| ASTM F 2229 : 2021 | Standard Specification for Wrought, Nitrogen Strengthened 23Manganese-21Chromium-1Molybdenum Low-Nickel Stainless Steel Alloy Bar and Wire for Surgical Implants (UNS S29108) |
| ASTM F 2181 : 2020 | Standard Specification for Wrought Seamless Stainless Steel Tubing for Surgical Implants |
| ASTM F 2193 : 2020 | Standard Specifications and Test Methods for Components Used in the Surgical Fixation of the Spinal Skeletal System |
| ASTM F 621 : 2012 : R2021 : EDT 1 | Standard Specification for Stainless Steel Forgings for Surgical Implants |
| ASTM F 746 : 2004 : R2014 | Standard Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials |
| ASTM E 18 : 2024 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM A 555/A555M : 2020 | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
| ASTM E 8/E8M : 2024 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 8/E8M : 2016 : REV A : EDT 1 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM E 29 : 2013 : R2019 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM A 484/A484M : 2023 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
| ASTM E 8/E8M : 2021 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM A 555/A555M : 2021 | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
| ASTM E 18 : 2022 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM E 10 : 2023 | Standard Test Method for Brinell Hardness of Metallic Materials |
| ASTM E 29 : 2002 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
| ASTM E 45 : 1997 : EDT 2 | Standard Test Methods for Determining the Inclusion Content of Steel |
| ASTM E 10 : 2001 | Standard Test Method for Brinell Hardness of Metallic Materials |
| ASTM E 45 : 2018 : REV A | Standard Test Methods for Determining the Inclusion Content of Steel |
| ASTM A 484/A484M : 2021 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
| ASTM E 354 : 2021 | Standard Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys |
| ASTM A 262 : 2001 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| ASTM E 18 : 2020 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM A 555/A555M : 2022 | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
| ASTM A 751 : 2021 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
| ASTM A 555/A555M : 2023 | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
| ASTM E 8/E8M : 2022 | Standard Test Methods for Tension Testing of Metallic Materials |
| ASTM A 262 : 1998 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| ASTM E 45 : 2018 : REV A : R2023 | Standard Test Methods for Determining the Inclusion Content of Steel |
| ASTM E 354 : 2021 : EDT 1 | Standard Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys |
| ASTM A 484/A484M : 2022 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
| ASTM F 746 : 2004 : R2021 | Standard Test Method for Pitting or Crevice Corrosion of Metallic Surgical Implant Materials |
| ASTM A 262 : 2015 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| ASTM A 751 : 2020 | Standard Test Methods and Practices for Chemical Analysis of Steel Products |
| ASTM A 484/A484M : 2024 | Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings |
| ASTM E 18 : 2019 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM E 354 : 2014 | Standard Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys |
| ASTM E 112 : 2013 : R2021 | Standard Test Methods for Determining Average Grain Size |
| ASTM E 112 : 2013 | Standard Test Methods for Determining Average Grain Size |
| ASTM A 484/A484M : 2023 : REV A | Standard Specification for General Requirements for Stainless Steel Bars, Billets, Shapes, and Forgings |
| ASTM E 407 : 2007 : R2015 : EDT 1 | Standard Practice for Microetching Metals and Alloys |
| ASTM A 484/A484M : 2020 : REV B | Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings |
| ASTM E 407 : 2023 | Standard Practice for Microetching Metals and Alloys |
| ASTM E 10 : 2018 | Standard Test Method for Brinell Hardness of Metallic Materials |
| ASTM A 262 : 2015 : R2021 | Standard Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels |
| ASTM E 29 : 2022 | Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.