ASTM F 1201 : 1988 : R1998
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Specification for Fluid Conditioner Fittings in Piping Applications Above 0°F
Hardcopy , PDF
11-11-2014
English
31-12-2010
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 01.07, 2017 Describes the minimum requirements for pressure-retaining components of fluid conditioner fittings.
| Committee |
F 25
|
| DocumentType |
Standard
|
| Pages |
4
|
| ProductNote |
Reconfirmed 1998
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1 This specification provides the minimum requirements for pressure-retaining components of fluid conditioner fittings. It addresses the pressure-retaining component design, fabrication, rating, marking, and testing.
1.2 This specification is not intended to override any of the present fluid conditioner fitting specifications specific to devices such as strainers, filters, and traps but should be used for devices for which a specific specification does not apply.
1.3 This specification provides sufficient requirements to allow a fluid conditioner fitting to be used in the marine environment.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASME PV CODE 8 DIV 2 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 2- ALTERNATIVE RULES |
| ASME B31.1 : 2016 | POWER PIPING |
| ASME PV CODE 9 : 2017 | BOILER AND PRESSURE VESSEL CODE - WELDING, BRAZING, AND FUSING QUALIFICATIONS - QUALIFICATION STANDARD FOR WELDING, BRAZING, AND FUSING PROCEDURES; WELDERS; BRAZERS; AND WELDING, BRAZING, AND FUSING OPERATORS |
| ASME PV CODE 8 DIV 1 : 2017 | BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS DIVISION 1 |
| ASME B16.11 : 2016 | FORGED FITTINGS, SOCKET-WELDING AND THREADED |
| MSS SP 67 : 2017 | BUTTERFLY VALVES |
| ASME PV CODE 8 DIV 3 : 2017 | BPVC Section VIII-BOILER AND PRESSURE VESSEL CODE - RULES FOR CONSTRUCTION OF PRESSURE VESSELS - ALTERNATIVE RULES FOR CONSTRUCTION OF HIGH PRESSURE VESSELS |
| ASME B16.15 : 2013 | CAST COPPER ALLOY THREADED FITTINGS: CLASSES 125 AND 250 |
| ASME B16.1 : 2015 | Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 |
| MSS SP 51 : 2012 | CLASS 150LW CORROSION RESISTANT FLANGES AND CAST FLANGED FITTINGS |
| ANSI B2.1 : LATEST | PIPE THREADS (EXCEPT DRYSEAL) |
| ASTM D 93 : 2016-07 | TEST METHODS FOR FLASH POINT BY PENSKY-MARTENS CLOSED CUP TESTER |
| MSS SP 61 : 2013 | PRESSURE TESTING OF VALVES |
| MSS SP 44 : 2016 | STEEL PIPELINE FLANGES |
| ASME B16.5 : 2017 | PIPE FLANGES AND FLANGED FITTINGS: NPS 1/2 THROUGH NPS 24 METRIC/INCH STANDARD |
| ASME B16.4 : 2016 | GRAY IRON THREADED FITTINGS: CLASSES 125 AND 250 |
| ASME B16.25 : 2012 | BUTTWELDING ENDS |
| ASME B16.3 : 2016 | MALLEABLE IRON THREADED FITTINGS: CLASSES 150 AND 300 |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.