ASTM E 670 : 2009 : R2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Testing Side Force Friction on Paved Surfaces Using the Mu-Meter
Hardcopy , PDF
12-11-2024
English
15-06-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.03, 2015 Describes the measurement of the side force friction of paved surfaces utilizing a device commonly called a Mu-Meter.
| Committee |
E 17
|
| DocumentType |
Test Method
|
| Pages |
12
|
| ProductNote |
Reconfirmed 2015
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers the measurement of the side force friction of paved surfaces utilizing a device commonly called a Mu-Meter.2
1.2This test method utilizes a measurement obtained by pulling the Mu-Meter, containing two freely rotating test wheels angled to the direction of motion, over a pavement surface at a constant speed while the test wheels are under a constant static load. This method provides data of the side force friction (and other data) along the whole length of the test surface being tested which is applied to a variety of computerized algorithms enabling the production of results including (but not limited to) rolling averages, numeric and graphical representations, friction mapping and reports formatted in the layout approved by a wide variety of national airport regulators.
1.3The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See also Section 6.
| ASTM D 2240 : 2000 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 3182 : 2015 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 297 : 2015 : REDLINE | Standard Test Methods for Rubber Products—Chemical Analysis |
| ASTM D 1765 : 2005 : REV A : EDT 1 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 1054 : 2002 : EDT 1 | Standard Test Method for Rubber Property-Resilience Using a Goodyear-Healey Rebound Pendulum |
| ASTM D 1765 : 2003 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 3182 : 2007 : R2012 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 1054 : 2002 : R2007 | Standard Test Method for Rubber Property-Resilience Using a Goodyear-Healey Rebound Pendulum (Withdrawn 2010) |
| ASTM D 1765 : 2004 : EDT 1 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM E 1551 : 2008 | Standard Specification for Special Purpose, Smooth<span class='unicode'>–</span>Tread Tire, Operated on Fixed Braking Slip Continuous Friction Measuring Equipment |
| ASTM D 1765 : 2017 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM E 1551 : 2016 : REDLINE | Standard Specification for a Size 4.00-8 Smooth Tread Friction Test Tire |
| ASTM D 1765 : 2014 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 3182 : 1989 : R2006 | Standard Practice for Rubber-Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 1765 : 2000 : REV A | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 2240 : 2004 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1765 : 2018 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 3182 : 1989 : R2001 : EDT 1 | Standard Practice for Rubber-Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 1765 : 2001 : EDT 1 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM E 1551 : 2016 | Standard Specification for a Size 4.00-8 Smooth Tread Friction Test Tire |
| ASTM D 1765 : 2019 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 1765 : 2004 : REV A | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 2240 : 2004 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1765 : 2001 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 1765 : 2016 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 1054 : 2002 | Test Method for Rubber Property-Resilience Using a Goodyear-Healey Rebound Pendulum |
| ASTM D 1765 : 2005 : REV A | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 1765 : 2013 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 1765 : 2006 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM E 1551 : 2006 | Standard Specification for Special Purpose, Smooth-Tread Tire, Operated on Fixed Braking Slip Continuous Friction Measuring Equipment |
| ASTM D 3182 : 2007 | Standard Practice for Rubber-Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 3182 : 2016 : REDLINE | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 1054 : 1991 : R2000 | Standard Test Method for Rubber Property-Resilience Using a Rebound Pendulum |
| ASTM D 2240 : 2002 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2240 : 2015 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2240 : 2003 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2240 : 2002 : REV B | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1765 : 2010 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM E 1551 : 2008 : R2015 | Standard Specification for Special Purpose, Smooth–Tread Tire, Operated on Fixed Braking Slip Continuous Friction Measuring Equipment |
| ASTM D 3182 : 1989 : R2001 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 1765 : 2004 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 2240 : 2015 : EDT 1 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 2240 : 2005 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 3182 : 1989 : R1994 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM E 1551 : 1993 : REV A : R1998 | Standard Specification for Special Purpose, Smooth-Tread Tire, Operated on Fixed Braking Slip Continuous Friction Measuring Equipment |
| ASTM D 2240 : 2005 : R2010 | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 3182 : 2016 | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
| ASTM D 2240 : 2002 : REV A | Standard Test Method for Rubber Property—Durometer Hardness |
| ASTM D 1765 : 2005 | Standard Classification System for Carbon Blacks Used in Rubber Products |
| ASTM D 3182 : 2015 : REV A | Standard Practice for Rubber—Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.