ASTM E 2925 : 2019 : REV A
Current
The latest, up-to-date edition.
Standard Specification for Manufactured Polymeric Drainage and Ventilation Materials Used to Provide a Rainscreen Function
Hardcopy , PDF
English
01-08-2019
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
E 06
|
| DocumentType |
Standard
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| Supersedes |
1.1This specification is applicable to manufactured polymeric materials used to provide a rainscreen function, a means for the drainage of liquid moisture and the ventilation of vapor moisture that enters an above-grade exterior wall assembly. Rainscreen materials that comply with this specification are intended to be used behind exterior cladding products and intended to cover one hundred percent (100 %) of the wall area that is designed to provide a rainscreen function to resist water infiltration.
1.2This specification addresses the following types of rainscreen materials:
1.2.1Type A—entangled mesh materials.
1.2.2Type B—formed/textured sheet material.
1.2.3Type C—formed battens.
1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM E 84 : 2023 : REV D | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM E 84 : 2023 : REV C | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 6108 : 2019 | Standard Test Method for Compressive Properties of Plastic Lumber and Shapes |
| ASTM G 154 : 2016 | Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials |
| ASTM E 84 : 2023 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM E 283/E283M : 2019 | Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Skylights, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen |
| ASTM G 154 : 2023 | Standard Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Materials |
| ASTM E 84 : 2021 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM C 578 : 2019 | Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation |
| ASTM E 84 : 2022 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 3045 : 2018 | Standard Practice for Heat Aging of Plastics Without Load |
| ASTM C 1338 : 2019 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM E 84 : 2024 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM C 1338 : 2019 : R2022 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM E 631 : 2015 : R2024 | Standard Terminology of Building Constructions |
| ASTM E 84 : 2020 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM E 84 : 2021 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM C 578 : 2022 | Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation |
| ASTM D 5322 : 2023 | Standard Practice for Laboratory Immersion Procedures for Evaluating the Chemical Resistance of Geosynthetics to Liquids |
| ASTM E 631 : 2015 | Standard Terminology of Building Constructions |
| ASTM E 84 : 2023 : REV B | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM C 578 : 2023 | Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation |
| ASTM D 5322 : 2017 | Standard Practice for Laboratory Immersion Procedures for Evaluating the Chemical Resistance of Geosynthetics to Liquids |
| ASTM E 84 : 2023 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM D 6108 : 2024 | Standard Test Method for Compressive Properties of Plastic Lumber and Shapes |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.