ASTM E 2206 : 2011 : R2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Force Calibration of Thermomechanical Analyzers
Hardcopy , PDF
17-04-2021
English
14-10-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method describes the calibration or performance confirmation of the electronically applied force signal for thermomechanical analyzers over the range of 0 to 1 N.
| Committee |
E 37
|
| DocumentType |
Test Method
|
| Pages |
3
|
| ProductNote |
Reconfirmed 2015
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method describes the calibration or performance confirmation of the electronically applied force signal for thermomechanical analyzers over the range of 0 to 1 N.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3There is no ISO method equivalent to this standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM E 2092 : 2018 : REV A | Standard Test Method for Distortion Temperature in Three-Point Bending by Thermomechanical Analysis |
| ASTM E 2769 : 2018 | Standard Test Method for Elastic Modulus by Thermomechanical Analysis Using Three-Point Bending and Controlled Rate of Loading |
| ASTM E 2347 : 2016 | Standard Test Method for Indentation Softening Temperature by Thermomechanical Analysis |
| ASTM E 1363 : 1997 : EDT 1 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 2161 : 2015 : R2019 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 2011 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2012 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2161 : 2015 | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 1142 : 1997 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2021 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 2161 : 2013 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 1142 : 2013 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2113 : 2000 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
| ASTM E 1142 : 2004 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2161 : 2015 : REDLINE | Standard Terminology Relating to Performance Validation in Thermal Analysis and Rheology |
| ASTM E 2113 : 2002 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
| ASTM E 1142 : 2006 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 473 : 2018 | Standard Terminology Relating to Thermal Analysis and Rheology |
| ASTM E 1142 : 2015 : R2020 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1363 : 2016 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 2113 : 2009 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
| ASTM E 2161 : 2001 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 2161 : 2006 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 1363 : 2008 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 2161 : 2008 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 1142 : 2007 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2015 : REDLINE | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2113 : 2018 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
| ASTM E 1142 : 2014 : REV A | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1363 : 2018 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 1363 : 2003 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 1142 : 2014 : REV B | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1363 : 2013 | Standard Test Method for Temperature Calibration of Thermomechanical Analyzers |
| ASTM E 1142 : 2005 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 1142 : 2015 | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2113 : 2013 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
| ASTM E 2161:2006 | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 473 : 2016-05 | TERMINOLOGY RELATING TO THERMAL ANALYSIS AND RHEOLOGY |
| ASTM E 1142 : 2011 : REV B | Standard Terminology Relating to Thermophysical Properties |
| ASTM E 2161 : 2007 : REV A | Standard Terminology Relating to Performance Validation in Thermal Analysis |
| ASTM E 2113 : 2004 | Standard Test Method for Length Change Calibration of Thermomechanical Analyzers |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.