ASTM D 8291 : 2021 : REV A : EDT 1
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine
Hardcopy , PDF
08-11-2023
English
27-06-2022
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
57
|
| ProductNote |
ε1NOTE—Editorially updated TMC governance information in June 2022.
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This laboratory engine test evaluates the ability of an automotive engine to mitigate preignition in the combustion chambers in gasoline, turbocharged, direct-injection (GTDI) engines under low-speed and high-load operating conditions. This test method is commonly known as the Ford low-speed, preignition (LSPI) test.
1.1.1In vehicles, equipped with relatively small GTDI spark-ignition engines, preignition has occasionally occurred when the vehicles are operated under low-speed and high-load conditions. Uncontrolled, preignition may cause destructive engine damage.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1Exceptions—Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing size, wire gauge, or specified single source equipment.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 8279 : 2023 | Standard Test Method for Determination of Timing-Chain Wear in a Turbocharged, Direct-Injection, Spark-Ignition, Four-Cylinder Engine |
| ASTM D 4485 : 2020 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 8047 : 2023 | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
| ASTM D 8047 : 2019 : EDT 1 | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
| ASTM D 86 : 2023 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 1319 : 2018 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 86 : 2020 : REV A | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 1298 : 2012 : REV B : R2017 : EDT 1 | Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
| ASTM D 2699 : 2022 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 86 : 2018 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 1298 : 2012 : REV B : R2017 | Standard Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method |
| ASTM D 445 : 2021 : EDT 2 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 2700 : 2022 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2699 : 2023 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 445 : 2017 : REV A | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 86 : 2019 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 2709 : 2016 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM D 2700 : 2022 : REV B | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 86 : 2012 | Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure |
| ASTM D 4485 : 2020 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 2699 : 2022 : REV A | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2699 : 2019 : EDT 1 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 86 : 2020 : REV B | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 86 : 2016 : REV A | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 445 : 2019 : REV A | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 5453 : 2016 : EDT 1 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 445 : 2019 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 381 : 2019 | Standard Test Method for Gum Content in Fuels by Jet Evaporation |
| ASTM D 2709 : 2022 | Standard Test Method for Water and Sediment in Middle Distillate Fuels by Centrifuge |
| ASTM D 130 : 2018 | Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test |
| ASTM D 381 : 2022 | Standard Test Method for Gum Content in Fuels by Jet Evaporation |
| ASTM D 2699 : 2021 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 2622 : 2021 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
| ASTM D 445 : 2021 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 381 : 2012 : R2017 | Standard Test Method for Gum Content in Fuels by Jet Evaporation |
| ASTM D 86 : 2020 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 2700 : 2022 : REV A | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 4485 : 2022 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 3237 : 2017 | Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy |
| ASTM D 5453 : 2019 | Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Spark Ignition Engine Fuel, Diesel Engine Fuel, and Engine Oil by Ultraviolet Fluorescence |
| ASTM D 445 : 2018 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 86 : 2015 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 445 : 2021 : EDT 1 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 3237 : 2022 | Standard Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy |
| ASTM D 86 : 2017 | Standard Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure |
| ASTM D 2700 : 2023 | Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 1319 : 2019 | Standard Test Method for Hydrocarbon Types in Liquid Petroleum Products by Fluorescent Indicator Adsorption |
| ASTM D 525 : 2012 : REV A | Standard Test Method for Oxidation Stability of Gasoline (Induction Period Method) |
| ASTM D 2699 : 2019 | Standard Test Method for Research Octane Number of Spark-Ignition Engine Fuel |
| ASTM D 130 : 2012 | Standard Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test |
| ASTM D 4485 : 2022 : EDT 1 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 2622 : 2016 | Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.