ASTM D 8279 : 2021
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determination of Timing-Chain Wear in a Turbocharged, Direct-Injection, Spark-Ignition, Four-Cylinder Engine
Hardcopy , PDF
30-06-2022
English
12-01-2021
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
66
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1Undesirable timing-chain wear has been observed with gasoline, turbocharged, direct-injection (GTDI) engines in field service, and data from correlating laboratory engine tests have shown that chain wear can be affected by appropriately formulated engine lubricating. A laboratory engine test has been developed to provide a means for screening lubricating oils for that specific purpose. The laboratory engine test is 216 h in length, conducted under varying conditions, and the increase in timing-chain length determined at the end of test is the primary result. This test method is commonly known as the Sequence X, Chain Wear (CW) Test.
1.2The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.2.1Exception—Where there is no direct SI equivalent such as screw threads, national pipe threads/diameters, tubing size, or specified single source equipment.
1.3Table of Contents:
| Section | |
| Scope | 1 |
| Referenced Documents | 2 |
| Terminology | 3 |
| Summary of Test Method | 4 |
| Significance and Use | 5 |
| Apparatus | 6 |
| Test Engine | 6.1 |
| Reagents and Materials | 7 |
| Preparation of Apparatus | 8 |
| Timing-chain Preparation, Installation, and Measurement | 8.20 |
| Test Stand Installation | 8.21 |
| Electronic Throttle Controller | 8.21.17 |
| Temperature Measurement | 8.23 |
| Pressure Measurement | 8.24 |
| Flowrate Measurement | 8.25 |
| Blowby Flowrate | 8.26 |
| Stand Calibration | 9 |
| Test Procedure | 10 |
| Pre-Test Procedure and Engine Break-In | 10.1 |
| Engine Start-up Procedures | 10.2 |
| Test Sequence | 10.3 |
| Engine Shutdown Procedures | 10.4 |
| Blowby Flowrate Measurement | 10.5 |
| Parameter Logging | 10.6 |
| Oil Consumption Calculation | 10.7 |
| General Maintenance | 10.8 |
| Special Maintenance Procedures | 10.9 |
| Blowby Flowrate Adjustment | 10.10 |
| Diagnostic Data Review | 11 |
| Test Results | 12 |
| Report | 13 |
| Precision and Bias | 14 |
| Keywords | 15 |
| ANNEXES | |
| ASTM TMC Organization | Annex A1 |
| ASTM TMC: Calibration Procedures | Annex A2 |
| ASTM TMC: Maintenance Activities | Annex A3 |
| ASTM TMC: Related Information | Annex A4 |
| Engine and Stand Parts | Annex A5 |
| Safety Precautions | Annex A6 |
| Engine Rebuild Templates | Annex A7 |
| Engine Build Records | Annex A8 |
| Cylinder Head Build | A8.1 |
| Cylinder Bore Measurement | A8.2 |
| Bearing Journal Measurements | A8.3 |
| Engine Part Photographs, Schematics and Figures | Annex A9 |
| Control and Data Acquisition Requirements | Annex A10 |
| Dipstick Oil Level to Charge Conversions | Annex A11 |
| Sequence X Report Forms and Data Acquisition | Annex A12 |
| APPENDIXES | |
| Sources of Materials and Information | Appendix X1 |
| Suggested Designs for Engine Fixing Brackets | Appendix X2 |
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 4485 : 2020 | Standard Specification for Performance of Active API Service Category Engine Oils |
| ASTM D 5967 : 2019 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 4175 : 2020 : REV B | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 5967 : 2021 | Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine |
| ASTM D 8047 : 2019 : EDT 1 | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
| ASTM D 8291 : 2021 : REV A | Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine |
| ASTM D 6304 : 2004 : REV A : EDT 1 | Standard Test Method for Determination of Water in Petroleum Products, Lubricating Oils, and Additives by Coulometric Karl Fisher Titration |
| ASTM D 4175 : 2022 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 235 : 2022 | Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) |
| ASTM D 4175 : 2001 : EDT 1 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 4175 : 2020 : REV B : EDT 1 | Standard Terminology Relating to Petroleum Products, Liquid Fuels, and Lubricants |
| ASTM D 8047 : 2019 | Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine |
| ASTM D 4175 : 2002 | Standard Terminology Relating to Petroleum, Petroleum Products, and Lubricants |
| ASTM D 445 : 1988 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and the Calculation of Dynamic Viscosity) |
| ASTM D 4739 : 1996 | Standard Test Method for Base Number Determination by Potentiometric Titration |
| ASTM D 8291 : 2020 : REV A | Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine |
| ASTM D 664 : 1995 | Standard Test Method for Acid Number of Petroleum Products by Potentiometric Titration |
| ASTM D 445 : 2019 : REV A | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 6593 : 2018 : EDT 1 | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
| ASTM D 235 : 2002 : R2012 | Standard Specification for Mineral Spirits (Petroleum Spirits) (Hydrocarbon Dry Cleaning Solvent) (Withdrawn 2021) |
| ASTM D 6593 : 2001 | Standard Test Method for Evaluation of Automotive Engine Oils for Inhibition of Deposit Formation in a Spark-Ignition Internal Combustion Engine Fueled with Gasoline and Operated Under Low-Temperature, Light-Duty Conditions |
| ASTM D 445 : 2001 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (the Calculation of Dynamic Viscosity) |
| ASTM D 445 : 2021 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 445 : 2021 : EDT 1 | Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity) |
| ASTM D 8291 : 2021 | Standard Test Method for Evaluation of Performance of Automotive Engine Oils in the Mitigation of Low-Speed, Preignition in the Sequence IX Gasoline Turbocharged Direct-Injection, Spark-Ignition Engine |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.