ASTM D 7992/D7992M : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Elevated Temperature and Moisture Conditioning of Pultruded Fiber Reinforced Polymer (FRP) Composites Used in Structural Designs
Hardcopy , PDF
17-01-2024
English
13-10-2015
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 08.03, 2016 Specifies procedures for elevated temperature and moisture conditioning of pultruded FRP composites intended for use in structural design applications.
| Committee |
D 20
|
| DocumentType |
Standard Practice
|
| Pages |
3
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
1.1In general, it is feasible that the mechanical properties of FRP composites will be affected by environmental conditions such as exposure to moisture at elevated temperatures. In order to make reliable comparisons between different materials under elevated temperature and moisture environmental conditions, it is necessary to standardize the elevated temperature and moisture conditions to which specimens of these materials are subjected prior to and during testing. This practice defines procedures for elevated temperature and moisture conditioning of pultruded FRP composites intended for use in structural design applications. The conditioning medium representing elevated temperature and moisture exposure described in this standard practice is distilled water maintained at 37.8 ± 1.5°C (100 ± 3°F) for 1000 hours.
1.2Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 7290 : 2006 : R2017 | Standard Practice for Evaluating Material Property Characteristic Values for Polymeric Composites for Civil Engineering Structural Applications |
| ASTM D 618 : 2013 : REDLINE | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 3918 : 2011 : REDLINE | Standard Terminology Relating to Reinforced Plastic Pultruded Products |
| ASTM D 7290 : 2006 : R2011 | Standard Practice for Evaluating Material Property Characteristic Values for Polymeric Composites for Civil Engineering Structural Applications |
| ASTM D 7745 : 2011 | Standard Practice for Testing Pultruded Composites |
| ASTM D 7290 : 2006 : R2022 | Standard Practice for Evaluating Material Property Characteristic Values for Polymeric Composites for Civil Engineering Structural Applications |
| ASTM D 6641/D6641M : 2023 | Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture |
| ASTM D 6641/D6641M : 2016 : EDT 2 | Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture |
| ASTM D 3918 : 1996 | Standard Terminology Relating to Reinforced Plastic Pultruded Products |
| ASTM D 618 : 2013 | Standard Practice for Conditioning Plastics for Testing |
| ASTM D 3918 : 2011 | Standard Terminology Relating to Reinforced Plastic Pultruded Products (Withdrawn 2020) |
| ASTM D 6641/D6641M : 2016 : EDT 1 | Standard Test Method for Compressive Properties of Polymer Matrix Composite Materials Using a Combined Loading Compression (CLC) Test Fixture |
| ASTM D 7290 : 2006 | Standard Practice for Evaluating Material Property Characteristic Values for Polymeric Composites for Civil Engineering Structural Applications |
| ASTM D 7745 : 2019 | Standard Practice for Testing Pultruded Composites |
| ASTM D 618 : 2021 | Standard Practice for Conditioning Plastics for Testing |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.