ASTM D 75/D75M : 2014 : REDLINE
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Practice for Sampling Aggregates
01-02-2020
English
19-06-2014
Important note : All end users must be registered with an Account prior to user licenses being assigned.CONTAINED IN VOL. 04.03, 2015 Defines sampling of coarse and fine aggregates for the following purposes: 1) Preliminary investigation of the potential source of supply, 2) Control of the product at the source of supply, 3) Control of the operations at the site of use, and 4) Acceptance or rejection of the materials.
| Committee |
D 04
|
| DevelopmentNote |
Supersedes ASTM D 75. (06/2009) Also numbered as AASHTO T 2. (12/2013)
|
| DocumentType |
Redline
|
| Pages |
9
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This practice covers sampling of coarse and fine aggregates for the following purposes:
1.1.1Preliminary investigation of the potential source of supply,
1.1.2Control of the product at the source of supply,
1.1.3Control of the operations at the site of use, and
1.1.4Acceptance or rejection of the materials.
1.2The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| ASTM D 5284 : 2009 | Standard Test Method for Sequential Batch Extraction of Waste with Acidic Extraction Fluid |
| ASTM D 4793 : 2009 | Standard Test Method for Sequential Batch Extraction of Waste with Water |
| ASTM C 1797 : 2017 : REDLINE | Standard Specification for Ground Calcium Carbonate and Aggregate Mineral Fillers for use in Hydraulic Cement Concrete |
| ASTM D 8140 : 2018 | Standard Guide for the Use of Foundry Sand in Asphalt Mixtures |
| ASTM D 7655/D7655M : 2012 : R2017 | Standard Classification for Size of Aggregate Used as Ballast for Membrane Roof Systems |
| ASTM D 5233 : 1992 : R2009 | Standard Test Method for Single Batch Extraction Method for Wastes |
| ASTM C 641 : 2017 : REDLINE | Standard Test Method for Iron Staining Materials in Lightweight Concrete Aggregates |
| ASTM D 1865/D1865M : 2009 | Standard Test Method for Hardness of Mineral Aggregate Used on Built-Up Roofs |
| ASTM D 1864/D1864M : 1989 : R2017 | Standard Test Method for Moisture in Mineral Aggregate Used on Built-Up Roofs |
| AASHTO T 346 : 2013 | METHOD OF TEST FOR GLASS BEADS USED IN PAVEMENT MARKINGS |
| ASTM D 5233 : 1992 : R1999 | Standard Test Method for Single Batch Extraction Method for Wastes |
| ANSI/AWWA B100 : 2016 | GRANULAR FILTER MATERIAL |
| ASTM C 332 : 2017 : REDLINE | Standard Specification for Lightweight Aggregates for Insulating Concrete |
| ASTM D 420 : 2018 | Standard Guide for Site Characterization for Engineering Design and Construction Purposes |
| ASTM E 1109 : 1986 : R1996 | Standard Test Method for Determining the Bulk Density of Solid Waste Fractions |
| ASTM E 1109 : 1986 : R2004 | Standard Test Method for Determining the Bulk Density of Solid Waste Fractions |
| ASTM E 1109 : 1986 : R2009 | Standard Test Method for Determining the Bulk Density of Solid Waste Fractions |
| ASTM D 5233 : 1992 : R2017 | Standard Test Method for Single Batch Extraction Method for Wastes |
| ASTM E 2788/E2788M : 2018 | Standard Specification for Use of Expanded Shale, Clay and Slate (ESCS) as a Mineral Component in the Growing Media and the Drainage Layer for Vegetative (Green) Roof Systems |
| ASTM C 535 : 2016 : REDLINE | Standard Test Method for Resistance to Degradation of Large-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine |
| ASTM F 2980 : 2013 | Standard Test Method for Analysis of Heavy Metals in Glass by Field Portable X-Ray Fluorescence (XRF) |
| AWWA A100 : 2015 | WATER WELLS |
| ACI 533R : 2011 | GUIDE FOR PRECAST CONCRETE WALL PANELS |
| ASTM C 494/C494M : 2017 : REDLINE | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 1761/C1761M : 2017 : REDLINE | Standard Specification for Lightweight Aggregate for Internal Curing of Concrete |
| AWWA C104/A21.4 : 2016 | CEMENT - MORTAR LINING FOR DUCTILE-IRON PIPE AND FITTINGS EFFECTIVE |
| AASHTO T 157 : 2012(R2016) | Standard Method of Test for Air-Entraining Admixtures for Concrete<br> |
| ASTM C 87/C87M : 2017 : REDLINE | Standard Test Method for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar |
| ASTM C 1077 : 2017 : REDLINE | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
| ASTM F 2980 : 2013 : R2017 | Standard Test Method for Analysis of Heavy Metals in Glass by Field Portable X-Ray Fluorescence (XRF) |
| ASTM D 7655/D7655M : 2012 | Standard Classification for Size of Aggregate Used as Ballast for Membrane Roof Systems |
| ASTM D 4793 : 2009 : R2017 | Standard Test Method for Sequential Batch Extraction of Waste with Water |
| ASTM D 1864/D1864M : 1989 : R2009 : EDT 1 | Standard Test Method for Moisture in Mineral Aggregate Used on Built-Up Roofs |
| ACI 207.5R : 2011 | REPORT ON ROLLER-COMPACTED MASS CONCRETE |
| ASTM D 5233 : 1992 : R2004 | Standard Test Method for Single Batch Extraction Method for Wastes |
| ASTM C 1451 : 2018 : REDLINE | Standard Practice for Determining Variability of Concrete-Making Materials From a Single Source |
| ASTM C 1797M : 2016 | Standard Specification for Ground Calcium Carbonate and Aggregate Mineral Fillers for use in Hydraulic Cement Concrete |
| ASTM D 1865/D1865M : 2009 : R2017 | Standard Test Method for Hardness of Mineral Aggregate Used on Built-Up Roofs |
| ASTM D 8155 : 2017 | Standard Practice for Shake Extraction of Solid Mining and Metallurgical Processing Waste with Water |
| ASTM D 5284 : 2009 : R2017 | Standard Test Method for Sequential Batch Extraction of Waste with Acidic Extraction Fluid |
| ASTM E 122 : 2017 : REDLINE | Standard Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process |
| ASTM D 3666 : 2016 : REDLINE | Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials |
| ASTM E 105 : 2016 : REDLINE | Standard Practice for Probability Sampling of Materials |
| ASTM C 702 : 1998 | Standard Practice for Reducing Samples of Aggregate to Testing Size |
| ASTM D 2234/D2234M : 2017 : REDLINE | Standard Practice for Collection of a Gross Sample of Coal |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.