ASTM D 7319 : 2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Determination of Existent and Potential Sulfate and Inorganic Chloride in Fuel Ethanol and Butanol by Direct Injection Suppressed Ion Chromatography
Available format(s)
Hardcopy , PDF
Superseded date
18-10-2022
Superseded by
Language(s)
English
Published date
06-10-2017
Important note : All end users must be registered with an Account prior to user licenses being assigned.This test method covers a direct injection ion chromatographic procedure for determining existent and potential inorganic sulfate and total inorganic chloride content in hydrous and anhydrous denatured ethanol and butanol to be used in motor fuel applications.
| Committee |
D 02
|
| DocumentType |
Test Method
|
| Pages |
10
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers a direct injection ion chromatographic procedure for determining existent and potential inorganic sulfate and total inorganic chloride content in hydrous and anhydrous denatured ethanol and butanol to be used in motor fuel applications. It is intended for the analysis of ethanol and butanol samples containing between 1.0 mg/kg to 20 mg/kg of existent or potential inorganic sulfate and 1.0 mg/kg to 50 mg/kg of inorganic chloride.
Note 1:Tertiary butanol is not included in this test method. 1-butanol, 2-butanol, and isobutanol are included in the testing and research report for this test method.
1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.
1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM D 7578 : 2018 | Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants |
| ASTM D 8149 : 2017 | Standard Practice for Optimization, Calibration, and Validation of Ion Chromatographic Determination of Heteroatoms and Anions in Petroleum Products and Lubricants |
| ASTM D 7328 : 2017 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
| ASTM D 4806 : 2019 | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
| ASTM D 7455 : 2019 | Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis |
| ASTM D 7328 : 2023 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
| ASTM D 4806 : 2021 : REV A | Standard Specification for Denatured Fuel Ethanol for Blending with Gasolines for Use as Automotive Spark-Ignition Engine Fuel |
| ASTM D 8149 : 2020 | Standard Practice for Optimization, Calibration, and Validation of Ion Chromatographic Determination of Heteroatoms and Anions in Petroleum Products and Lubricants |
| ASTM D 7862 : 2021 | Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel |
| ASTM D 7794 : 2021 | Standard Practice for Blending Mid-Level Ethanol Fuel Blends for Flexible-Fuel Vehicles with Automotive Spark-Ignition Engines |
| ASTM D 5798 : 2021 | Standard Specification for Ethanol Fuel Blends for Flexible-Fuel Automotive Spark-Ignition Engines |
| ASTM D 7578 : 2020 | Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants |
| ASTM D 8076 : 2021 : REV B | Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines |
| ASTM D 7862 : 2019 | Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel |
| ASTM D 7794 : 2018 : REV A | Standard Practice for Blending Mid-Level Ethanol Fuel Blends for Flexible-Fuel Vehicles with Automotive Spark-Ignition Engines |
| ASTM D 8076 : 2018 | Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines |
| ASTM D 4057 : 2019 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6792 : 2021 : REV A | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| ASTM D 4057 : 1995 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2010 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2013 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4177 : 2016 : EDT 1 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2017 : REV A | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2017 : REV B | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4052 : 1996 : R2002 : EDT 1 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
| ASTM D 6299 : 2009 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4177 : 1995 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 7318 : 2019 : EDT 1 | Standard Test Method for Existent Inorganic Sulfate in Ethanol by Potentiometric Titration |
| ASTM D 4057 : 2012 : R2018 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 4052 : 2018 : REV A | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 6299 : 2013 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6792 : 2006 | Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 6299 : 2021 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6792 : 2004 | Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 1193 : 1977 : R1983 : EDT 1 | Standard Specification for Reagent Water |
| ASTM D 7318 : 2011 | Standard Test Method for Existent Inorganic Sulfate in Ethanol by Potentiometric Titration |
| ASTM D 6299 : 2010 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 7318 : 2007 | Standard Test Method for Total Inorganic Sulfate in Ethanol by Potentiometric Titration |
| ASTM D 4052 : 2009 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 4057 : 1981 : EDT 2 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6792 : 2021 : REV B | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| ASTM D 6792 : 2004 : REV A | Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 7318 : 2013 | Standard Test Method for Existent Inorganic Sulfate in Ethanol by Potentiometric Titration |
| ASTM D 7328 : 2013 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
| ASTM D 6792 : 2005 | Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 5827 : 2009 : EDT 1 | Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography |
| ASTM D 6299 : 2000 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2010 : EDT 2 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6299 : 2016 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4057 : 2006 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 1193 : 2006 : R2011 | Standard Specification for Reagent Water |
| ASTM D 5827 : 2022 | Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography |
| ASTM D 4177 : 2015 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6792 : 2020 | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| ASTM D 4052 : 2011 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 6299 : 2019 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6792 : 2021 | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| ASTM D 4052 : 2016 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 4057 : 2012 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2000 : REV A | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6792 : 2013 | Standard Practice for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 6792 : 2017 | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| ASTM D 7328 : 2016 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
| ASTM D 7318 : 2019 | Standard Test Method for Existent Inorganic Sulfate in Ethanol by Potentiometric Titration |
| ASTM D 6792 : 2007 | Standard Practice for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 4177 : 2022 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 1193 : 1991 | Standard Specification for Reagent Water |
| ASTM D 6792 : 2021 : REV C | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| ASTM D 6299 : 2020 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4177 : 1995 : R2010 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2008 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4177 : 1995 : R2000 | Standard Practice for Automatic Sampling of Peroleum and Petroleum Products |
| ASTM D 6299 : 2002 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4052 : 1996 | Standard Test Method for Density and Relative Density of Liquids by Digital Density Meter |
| ASTM D 5827 : 1995 | Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography |
| ASTM D 6299 : 2022 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 6792 : 2022 | Standard Practice for Quality Management Systems in Petroleum Products, Liquid Fuels, and Lubricants Testing Laboratories |
| ASTM D 7328 : 2007 | Standard Test Method for Determination of Total and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
| ASTM D 4057 : 2022 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 7328 : 2011 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
| ASTM D 7328 : 2017 | Standard Test Method for Determination of Existent and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
| ASTM D 4177 : 2016 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4052 : 2022 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 1193 : 1970 | Standard Specification For Reagent Water |
| ASTM D 6792 : 2003 | Standard Guide for Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 4177 : 2020 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4177 : 1995 : R2005 | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 1193 : 2006 | Standard Specification for Reagent Water |
| ASTM D 7318 : 2018 | Standard Test Method for Existent Inorganic Sulfate in Ethanol by Potentiometric Titration |
| ASTM D 5827 : 2009 : R2015 | Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography |
| ASTM D 1193 : 1999 | Standard Specification for Reagent Water |
| ASTM D 6792 : 2002 | Standard Guide for A Quality System in Petroleum Products and Lubricants Testing Laboratories |
| ASTM D 6299 : 2007 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4052 : 2015 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 6299 : 2007 : EDT 1 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 4057 : 1995 : R2000 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 6299 : 2020 : REV A | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 5827 : 2009 | Standard Test Method for Analysis of Engine Coolant for Chloride and Other Anions by Ion Chromatography |
| ASTM D 6299 : 2017 | Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance |
| ASTM D 1193 : 2006 : R2018 | Standard Specification for Reagent Water |
| ASTM D 4177 : 2015 : REV A | Standard Practice for Automatic Sampling of Petroleum and Petroleum Products |
| ASTM D 4057 : 2006 : R2011 | Standard Practice for Manual Sampling of Petroleum and Petroleum Products |
| ASTM D 7328 : 2007 : EDT 1 | Standard Test Method for Determination of Total and Potential Inorganic Sulfate and Total Inorganic Chloride in Fuel Ethanol by Ion Chromatography Using Aqueous Sample Injection |
| ASTM D 4052 : 2018 | Standard Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter |
| ASTM D 6299 : 2002 | Standard Practice for Applying Statistical Quality Assurance Techniques to Evaluate Analytical Measurement System Performance |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.