ASTM D 7277 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Performance Testing of Articulating Concrete Block (ACB) Revetment Systems for Hydraulic Stability in Open Channel Flow
Hardcopy , PDF
12-08-2023
English
18-04-2016
Important note : All end users must be registered with an Account prior to user licenses being assigned.| Committee |
D 18
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1The purpose of this test method is to provide specifications for the hydraulic testing of full-scale articulating concrete block (ACB) revetment systems under controlled laboratory conditions for purposes of identifying stability performance in steep slope, high-velocity flows. The testing protocols, including system installation, test procedures, measurement techniques, analysis techniques, and reporting requirements are described in this test method.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in brackets are mathematical conversions to SI units that are provided for information only and are not considered standard. Reporting or use of units other than inch-pound shall not be considered non-conformance as long as the selected parameters described regarding flume construction by the inch-pound system used in this method are met as a minimum.
1.2.1The gravitational system of inch-pound units is used when dealing with inch-pound units. In this system, the pound (lbf) represents a unit of force (weight), while the unit for mass is slugs. The rationalized slug unit is not given, unless dynamic (F = ma) calculations are involved.
1.3All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026.
1.3.1The procedures used to specify how data are collected, recorded and calculated in this Guide are regarded as the industry standard. In addition they are representative of the significant digits that generally be retained. The procedures used do not consider material variation, purpose of obtaining the data, special purpose studies or any considerations for the user’s objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1:The quality of the result produced by this standard is dependent on the competence of the personnel performing it and the suitability of the equipment and facilities used. Agencies that meet criteria of Practice D3740 are generally considered capable of competent and objective testing. Users of this standard are cautioned that compliance with Practice D3740 does not in itself assure reliable results. Reliable results depend on many factors and Practice D3740 provides a means of evaluating some of these factors.
| ASTM D 7276 : 2016 | Standard Guide for Analysis and Interpretation of Test Data for Articulating Concrete Block (ACB) Revetment Systems in Open Channel Flow |
| ASTM D 2216 : 2005 | Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
| ASTM D 2487 : 2017 : EDT 1 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 5195 : 2008 | Standard Test Method for Density of Soil and Rock In-Place at Depths Below Surface by Nuclear Methods |
| ASTM D 653 : 2007 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 2216 : 2010 | Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
| ASTM D 3740 : 2012 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 4318 : 2005 | Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils |
| ASTM D 698 : 2000 | Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft<sup>3</sup> (600 kN-m/m<sup>3</sup>)) |
| ASTM D 422 : 1963 : R2007 : EDT 1 | Standard Test Method for Particle-Size Analysis of Soils |
| ASTM D 1556 : 2007 | Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method |
| ASTM D 3740 : 2019 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2004 : REV A : EDT 1 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 1556 : 2000 | Standard Test Method for Density and Unit Weight of Soil in Place by the Sand-Cone Method |
| ASTM D 3740 : 2008 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 6026 : 2013 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 698 : 2012 : R2021 | Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lbf/ft<sup>3</sup> (600 kN-m/m<sup>3</sup>)) |
| ASTM D 5195 : 1991 : R1996 | Standard Test Method for Density of Soil and Rock In-Place at Depths Below the Surface by Nuclear Methods |
| ASTM D 6026 : 2006 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 4318 : 2010 | Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils |
| ASTM D 5195 : 2021 | Standard Test Method for Density of Soil and Rock In-Place at Depths Below Surface by Nuclear Methods |
| ASTM D 3740 : 1999 : REV C | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 4318 : 2000 | Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils |
| ASTM D 653 : 2022 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 653 : 2020 : EDT 1 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 6026 : 1999 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2011 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 6026 : 2001 : EDT 1 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2010 | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 653 : 2021 : REV A | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 2216 : 2019 | Standard Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
| ASTM D 4318 : 2017 : EDT 1 | Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils |
| ASTM D 6026 : 1996 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2004 : REV A | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 3740 : 2001 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 2487 : 2006 : EDT 1 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 653 : 2021 | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 653 : 2021 : REV B | Standard Terminology Relating to Soil, Rock, and Contained Fluids |
| ASTM D 4318 : 2010 : EDT 1 | Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils |
| ASTM D 6026 : 1996 : EDT 1 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 3740 : 2012 : REV A | Standard Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 4318 : 2017 | Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils |
| ASTM D 3740 : 2003 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 2487 : 2010 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 2216 : 1998 | Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass |
| ASTM D 2487 : 2000 | Standard Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 2487 : 2006 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 6026 : 2021 | Standard Practice for Using Significant Digits and Data Records in Geotechnical Data |
| ASTM D 2216 : 1971 | Standard Method of Laboratory Determination Of Moisture Content Of Soil |
| ASTM D 5195 : 2014 | Standard Test Method for Density of Soil and Rock In-Place at Depths Below Surface by Nuclear Methods |
| ASTM D 6026 : 2001 | Standard Practice for Using Significant Digits in Geotechnical Data |
| ASTM D 2487 : 2011 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 2487 : 2017 | Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) |
| ASTM D 5195 : 2014 : EDT 1 | Standard Test Method for Density of Soil and Rock In-Place at Depths Below Surface by Nuclear Methods |
| ASTM D 3740 : 2004 | Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction |
| ASTM D 2487 : 1969 : R1975 | Standard Test Method for Classification Of Soils For Engineering Purposes |
| ASTM D 5195 : 2002 | Standard Test Method for Density of Soil and Rock In-Place at Depths Below the Surface by Nuclear Methods |
| ASTM D 698 : 2012 : EDT 2 | Standard Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12 400 ft-lbf/ft<sup>3</sup> (600 kN-m/m<sup>3</sup>)) |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.